Polaroid Mint User manual
Pocket Printer
USER GUIDE
3
Thank you for purchasing the Polaroid Mint Pocket Printer. This User Guide is
intended to provide you with guidelines to ensure that operation of this product
is safe and does not pose risk to the user. Any use that does not conform to the
guidelines described in this User Guide may void the limited warranty.
Please read all directions before using the product and retain this guide for
reference. This product is intended for household use only.
This product is covered by a limited one-year warranty. Coverage is subject to limits
and exclusions. See warranty for details.
4 5
BE SAFE WITH POLAROID MINT
• Never leave your printer or the ZINK®
paper in an area that might become
extremely hot or where it will be
exposed to direct sunlight for a long
time. This can cause your printer to
overheat or suffer other problems.
• Don’t get it wet! If you need to clean
your printer, use a soft cloth that’s
been slightly dampened with water or
rubbing alcohol, and gently wipe away
any dirty spots. Don’t submerge the
whole thing in water, ever.
• Be careful with your printer. Try not to
drop it, or shake it violently. The inside
of the printer has a lot of very small
parts that could break if they are jostled
around too much.
• Always use the charging cable that
comes in your box to charge your
printer, and be careful that it doesn’t
get too hot while charging. If you
feel the printer overheating while it
charges, immediately disconnect it
from the power source and let it cool
down before turning it back on.
• The Polaroid Mint Pocket Printer
absolutely will not work without
downloading the Android™or iOS
application. If you do not have an
Android™phone or an iPhone®,
unfortunately, this printer will not work
for you.
6 7
WHAT COMES IN THE BOX? GET TO KNOW YOUR PRINTER
1. Power Button
2.Micro USB Charging Port
3.Charging Indicator Light
4.Photo Print Slot
Polaroid ZINK®Paper
Starter Pack
User Guide &
Warranty
Micro USB
Charging Cable
Polaroid Mint Pocket Printer
1
2
4
3
8 9
GETTING READY
1. Charge it first: Before you start using
your new Polaroid Mint printer, plug it
into your computer or any USB charging
block with an output of one amp (1A) or
higher. The charging indicator will stay
red while the printer charges. Once it
turns green, it’s fully charged and ready
to use. The full charging process usually
takes approximately two (2) hours.
2. Load your ZINK®paper into the printer:
Follow the steps below to quickly and
easily get your new printer loaded with
ZINK®sticky-back paper so you can start
printing photos!
a. Open the paper tray in the back by
pressing down on the latch and
pulling it toward you.
b. Load the blue calibration sheet in
with the barcode facing down and the
ZINK®logo in the bottom right corner.
Place the other plain sheets on top
with the glossy side facing you.
Try to avoid touching the glossy side
so you don’t get fingerprints on it.
(You can load the whole stack as-is
from the packet, but sometimes it’s
easier to load the calibration sheet
first to make sure it’s seated correctly
in the tray.)
c. If the printer is off, the calibration
sheet will be slowly ejected from the
photo slot after a few seconds once
you turn the printer on. If the printer
10 11
is on, the calibration sheet will be
ejected from the photo print slot
when you print your first photo.
NOTE: Please make sure not to push
the paper in too far or else the paper
could jam or cause misprinting issues.
3. Download the Polaroid Mint application
from the Google Play™or Apple®App
Store®. You will need the app installed
on your phone for the printer to work.
START USING POLAROID MINT!
1. Turn the printer on by pressing the power
button on the side for two (2) seconds.
2. Pair the printer to your phone via
Bluetooth®:
a. Access your phone’s Bluetooth®
settings, usually found under the
general Settings menu.
b. Make sure the printer is on first, and
then allow your phone to scan for
new devices.
c. You will see “Polaroid Mint” appear
in the Bluetooth®list. Tap on it to start
pairing.
d. After a couple of seconds, your phone
12 13
should say “paired”.
3. Open up the Polaroid Mint application
from your phone, and start using your
new Polaroid Mint Pocket Printer!
SPECIFICATIONS
• Dimensions: 4.5" L x 3" W x 0.7" D
(116 x 77 x 18mm)
• Weight: 5.7 oz (162g)
• Colors Available: Black, White, Red,
Blue, Yellow
• Battery Capacity: 900mAh
• Battery Type: Lithium-polymer
• Prints Per Charge: ~50
• Supported Photo Paper: Polaroid ZINK®
2x3" sticky-back photo paper
14
Questions? Concerns? Get in Touch!
1-800-226-6534
Polaroid Mint Mobile Printer POLMP02
Table of contents
Other Polaroid Printer manuals
Polaroid
Polaroid Zip User manual
Polaroid
Polaroid Lab User manual
Polaroid
Polaroid P3500S User manual
Polaroid
Polaroid P100 Series User manual
Polaroid
Polaroid ColorShot Printer User manual
Polaroid
Polaroid P3500S User manual
Polaroid
Polaroid P-500 - Color User manual
Polaroid
Polaroid PoGo CZA-1001B User manual
Polaroid
Polaroid Lab User manual
Polaroid
Polaroid DIGITAL PHOTO PRINTER User manual
Polaroid
Polaroid P5000E User manual
Polaroid
Polaroid Polaprinter 8 x 10 3580 User manual
Polaroid
Polaroid Zip User manual
Polaroid
Polaroid Lab User manual
Polaroid
Polaroid PoGo CZA-1001B User manual
Polaroid
Polaroid P3000 User manual
Polaroid
Polaroid P100I User manual
Polaroid
Polaroid Zip User manual
Polaroid
Polaroid P751 User manual
Polaroid
Polaroid MD100I User manual
