Pioneer VSX-330 User manual

Service

Manual

PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.

PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium

PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

ⓒOnkyo & Pioneer Corporation 2015

AV Receiver

VSX-330

ORDER NO.

ARP4002

O-4555

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

Model Type Power Requirement Remarks

VSX-330-K

WMP

AC 220 V to 240 V

VSX-330-K

WMA

AC 220 V to 240 V

VSX-330-K

WMB

AC 220 V to 230 V

VSX-330-K

WMR

AC 220 V to 230 V

5 4 3

1 6

5 4 3

1 6

How to read suffix code of this model Note for Suffix Code

VSX-330

The following is explanation for the suffix code of these models.

V S X – 3 3 0 – K W M P

Model No.

D 120V AC

G 220～230V

H 220～230／240V

J 100V AC

M 220～240V AC

P 230V AC

U 100～240V AC

V 110～240V

W 120V／220～240V

Speaker System (without AMP.) :

0 Passive Subwoofer

F Front Speaker

C Center Speaker

R Rear Speaker

B Back Speaker

A Australia

B United Kingdom

C North American

D USA

F Taiwan

J Japan

K Korea

L Russia

P Europe

Q Hong Kong

R China

S Brazil

T Thai

U Worldwide

Speaker System (without AMP.) :

L Left channel

R Right channel

0 Center channel

Voltage Destination

The suffix code of each model is mentioned in serial

number label as per below.

M Malaysia

C China

U Japan

W Others

Production factory

Panel

5 4 3

1 6

5 4 3

1 6

VSX-330

Front Panel

Rear Panel

Remote Control Unit

Furnished Parts

Dimensions . . . . . 435 mm (W) x 168 mm (H) x 326.5 mm (D)

Weight (without package). . . . . . . . . . . . . . . . . . . . . . . . . 7.3 kg

Remote control . . . . . . . . .. . . . . . . . . . . . . . . . . 1

Dry cell batteries (AAA size IEC R03) . . . . . . . . 2

AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . 1

FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . 1

Quick start guide

Safety Brochure

Reset

5 4 3

1 6

5 4 3

1 6

VSX-330

Resetting the Main Unit

Use this procedure to reset all the receiver‘s settings to the factory default. Use the front panel

controls to do this.

1. Switch the receiver into standby.

2. While holding down [BAND], press and hold [STANDBY/ON] for about two seconds.

3. When you see RESET? appear in the display, press [AUTO SURROUND/STREAM

DIRECT]. OK? shows in the display.

4. Press [ALC/STANDARD SURR] to confirm.

How to Reset the Unit

Firmware

5432

VSX-330

Check to the software virsion of MAIN, HDMI & CEC (SUB) microcomputers

1. Make sure that the main unit is in STANDBY mode.

Press and hold about 3 seconds the both of " ENTER " and " STANDBY/ON " keys as same time,

Then it is appeared firmware version number.

At this time, When you press the " ENTER "key to display each UCOM version, Each time the " ENTER "key is

pressed, then indications on the FL display change as follows:

2. Turn the unit off.

MAIN Ucom "ENTER"

MAIN Xx.xx "ENTER" "ENTER" "ENTER"

SUB Ucom

SUB

zzz.zz

CEC

Vy,yy DSP

firmware All segments

lit.

"ENTER"

Firmware

543

5432

VSX-330

[Necessary Tools and Connections]

1MAIN microcomputer

• PC with a serial port

• RS-232C cable (9-pin to 9-pin, straight cable) (Marketing product)

•UPDATE jig: GGF1689 (with 10P to 10P FFC)

•Firmware

•Firmware Writer Application for PC

(Flash Programmer M16C Flash Starter M3A-0806 Software)

http://am.renesas.com/products/tools/flash_prom_programming/flash_programmers/m3a_080

6/downloads.jsp

Connect as shown in the below figure and follow the procedure as below

1. Install the software for updating on the PC

2. Unplug the AC Cord of the main unit

3. Insert the FFC with its contact surface facing the " mark.

2HDMI & CEC (SUB) microcomputer

• PC with a USB port

•USB cable (Marketing product)

•UPDATE jig: GGF1689 (with 10P to 10P FFC)

•Firmware

•Firmware Writer Application for PC

(Cypress/Spansion FLASH MCU Programmer for FM0+/FM3/FM4)

http://www.spansion.com/support/microcontrollers/developmentenvironment/Pages/mcu-

download.aspx

Connect as shown in the below figure and follow the procedure as below

1. Install the software for updating on the PC.

2. Unplug the power cord of the main unit.

Connect the FFC of the updating jig for updating to the main unit.

(Orient the FFC so that the conductive surface of

the connector faces the triangular a symbol.)

Preparation of Update

3. Start the software for updating on the PC.

No Necessary connect Main and HDMI&CEC at the same

time When you update Main, you connect Main only.

When you update HDMI&CEC, you connect HDMI&CEC only.

Straight Cable Adapter JIG's side

10P

RS-232C

Straight cable

PC (MAIN

microcomputer)

Rear side

10P to 10P FFC

UPDATE jig

GGF1689

Firmware

543

5432

How to Update (Main MCU) 1/5

VSX-330

Microcomputers update

[Procedures]

for MAIN microcomputer

1. Unplug the AC cord.

Connect the FFC cable. ( MAIN microcomputer )

Start up application "FlashSta" on the PC.

2. Plug the AC cord. (STANDBY mode)

For updating of the MAIN microcomputer, proceed with

the following steps in STANDBY mode.

Select for COM port.

[ if the following messages are displayed ]

Please push the cancel button and press the JIG's

RESET button.

And confirm a connection of FFC.

Please return to procedure 1.

3. Press the OK button.

3 Press OK button

to go to next step.

2. Enter ID.

Enter "ff" in all field.

1 Selection of upgrade file

Press the OK

2 Enter ID.

Press the OK button.

4. Select the update file and enter ID.

Note:

You need COM port number on Windows system

“My computer”, “Right Click”, “Properties”, “Device manager”

Click COM port properaties and Make sure COM port number.

Firmware

543

5432

How to Update (Main MCU) 2/5

5. Set speed update and update the MCU.

1 Set speed of update.

Press the OK button.

1 Set speed of update. Set

Baud rate to 38400.

2 Update the MCU.

E.P.R=>Erase+Program+Read

2 Update the MCU

Press the E.P.R … button

Click on "Open" 3 to open the File Selection window.

Select Intel Hex files (*.hex) in File Type.

If the following messages are displayed, shut the

update program down, and start the update again

from step 1.

Select the 9600 of the Board rate

then press the OK button

Press the OK button. Press the Exit button.

Please wait for until this window

disappears.

6. Update Finished MAIN microcomputer. 7. Unplug the AC cord.

Disconnect the FFC cable.

Push the JIG’s RESET button during 1

sec.

Press the OK button.

VSX-330

Firmware

543

5432

How to Update (HDMI Sub MCU) 3/5

VSX-330

for HDMI & CEC (SUB) microcomputer

[Procedures]

To perform updating, proceed as follows:

1. Set the values for Target MCU and Crystal Frequency, as

follows:

Target MCU: MB9AF156M/N/R 1

Crystal Frequency: 4MHz 2

2. Specify the software file to be updated.

Click on "Open" 3 to open the File Selection window.

Select Intel Hex files (*.hex) in File Type

3. Specify the COM PORT.

Click on "Set Environment" 4 to open the Environment Setting window.

Assign the COM PORT number 5, according to the environment.

Click on "OK" 6to close the Environment Setting window.

Click on "Full Operation (D+E+B+P)"7.

5. After the window shown below is displayed, turn the main unit on.

6. Press the Reset button of the updating jig for updating.

7. When it is appeared below window, Then power turn on unit (ON)

8. Click on "OK" 8.

Firmware

543

5432

How to Update (HDMI Sub MCU) 4/5

VSX-330

9. The indications in the window change, as indicated

below:

10. Updating has been successfully completed if

"Full Operation OK!" is displayed.

Note:

If an error message like the one shown below is displayed, after checking the

connection of the updating jig for updating and the COM PORT setting, start

updating again from Step 1.

11. Turn the main unit off then disconnect the updating jig for updating.

12. Perform Factory Reset on the main unit.

Or You have to make sure that It is necessary to turn on the unit at procedure 7

This manual suits for next models

Table of contents

Other Pioneer Receiver manuals

Pioneer

Pioneer VSX-42 ELITE User manual

Pioneer

Pioneer DEH-S31BT Use and care manual

Pioneer

Pioneer SPH-DA120 Operating manual

Pioneer

Pioneer VSX-820-K User manual

Pioneer

Pioneer XV-HTD520 User manual

Pioneer

Pioneer VSX-D908TX User manual

Pioneer

Pioneer VSX-518-K User manual

Pioneer

Pioneer MVH-X365BT User manual

Pioneer

Pioneer VSX-1020-K User manual

Pioneer

Pioneer VSX01TXH - Elite AV Receiver User manual

Pioneer

Pioneer VSX-521-K User manual

Pioneer

Pioneer DEH-2450UB User manual

Pioneer

Pioneer XV-DV535 User instructions

Pioneer

Pioneer XV-HTD540 User manual

Pioneer

Pioneer AVH-X8800BT User manual

Pioneer

Pioneer AVH-X8890BT User manual

Pioneer

Pioneer VSX-D412K User manual

Pioneer

Pioneer X-HM32VD-K User manual

Pioneer

Pioneer PDK-1014 User manual

Pioneer

Pioneer VSX-1017TXV-K - iPod Ready, XM Satellite User manual

Pioneer

Pioneer Elite SC-25 User manual

Pioneer

Pioneer MVH-AV285BT User manual

Pioneer

Pioneer X-HM31DAB-k User manual

Pioneer

Pioneer VSX-815-S/-K User manual

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual