PEERLESS SF 24D Guide
Installation and Assembly:
Dedicated Flat Wall Mount for Flat Panel Screens
Model: SF 24D
Max. Load Capacity: 200 lb (90.7 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
Features:
•Ultra-slim design holds the screen flat against the wall
•Integratedsecurityfeaturesprovideeffectivetheftdeterrence
2 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Wood Stud Wall .............................................................................................................................................4
Installation to Solid Concrete and Cinder Block Wall ............................................................................................................5
Installing Interface Bracket to PLP Adapter Plate .................................................................................................................6
InstallingInterfaceBracket to LCAdapterPlate....................................................................................................................7
Attaching Flat Panel Screen to Wall Mount ..........................................................................................................................8
For customer care call (800) 729-0307 or (708) 865-8870.
Accessories
•Metal Stud Fastener Kit (ACC 415)
Tools Needed for Assembly
•studfinder ("edge to edge" stud finder is recommended)
•drill
•1/4" bit for concrete and cinder block wall
•1/2" bit for metal stud wall
•5/32" bit for metal or wood stud wall
•3/8"socket wrench (socket with extended driver recommended)
•level
•6mm allen wrench
• Donot begin to install your Peerless product until you have read and understoodthe instructionsand warnings
containedin this Installation Sheet. If you have any questionsregarding anyof the instructions or warnings, please
callPeerlesscustomer care at1-800-729-0307.
• Thisproduct should onlybe installed by a qualifiedprofessional.
• Makesure thatthe supporting surface will safely support the combined load of the equipment and all attached hard-
wareandcomponents.
• Neverexceed the MaximumLoad Capacity of 200 lb(90.7 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" stud finder ishighly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, but donot overtighten. Overtighteningcan damage theitems, greatly reducingtheir holding
power.
WARNING
3 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
AA CC
DD EE
Description Qty Part
AA wall plate 1 200-1796
BB interface plate 1 200-0860
CC #14 x 2.5" wood screw 4 5S1-015-C03
DD Alligator® anchor 4 590-0097
EE M10 x 1.5 x 15 mm socket head screw 4 520-9262
FF 4 mm security allen wrench 1 560-1146
Parts List
FF
BB
4 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
Installation to Wood Stud Wall
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into
the center of the stud. The use of an "edge to edge"
stud finder is highly recommended.
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
CC
AA
CS = center of screen
CL = stud centerline
fig 1.3
Using a stud finder, locate the edges of the wood studs used in mounting this product. Use of an edge-to-edge stud
finder is highly recommended. Based on its edges and using a level, draw a vertical line down the center of each
stud. Mark a point (point 1) on the right stud centerline 4-5/8" above the center of screen as shown in figure 1.1.
Hold wall plate (AA) over point 1. Using a level to ensure plate is horizontal, mark three more points (points 2,3,
and 4) as shown in figure 1.2.
Drill 5/32" diameter holes 2-1/2" deep through studs at the four points.
Loosely fasten wall plate (AA) to wall using four #14 x 2-1/2" wood screws (CC) as shown in figure 1.3.
Note: For ease of installation, start with the top right wood screw first and work counterclockwise.
Level, hold, and then tighten all screws.
Skip to step 2 on page 6.
fig 1.1
1
4-5/8"
(117 mm)
CL
POINT 1 POINT 1
POINT 2
POINT 3 POINT 4
CL CL CL
fig 1.2
CS CS
5 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
Installation to Solid Concrete and Cinder Block Wall
1
CUTAWAY VIEW
INCORRECT
concrete
plaster/
drywall
AA
CORRECT
concrete
plaster/
drywall
AA
Position wall plate (AA) on wall so that upper slots are 4-5/8"
above desired center of screen. Use wall plate (AA), making
sure that it is level, as a template to mark holes. Drill four 1/4"
(6 mm) dia. holes to a minimum depth of 2-1/2" (64 mm).
Concrete must be 2000 psi density minimum. Insert anchors
(DD) in holes flush with wall as shown in figure 1.4. Place wall
plate (AA) over anchors and secure with #14 x 2-1/2" (6 mm
x 65 mm) wood screws (CC) as shown in figure 1.5. Make
sure wall plate is level and tighten all fasteners.
concrete
wall
Drill holes and insert anchors (DD)
Place wall plate (AA) over anchors and secure with
screws (CC)
Tighten all fasteners
CC
AA
1
3
2
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly
reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
DD
DD
CC
fig 1.4
fig 1.5
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
orother finishing material asshown below.Ifmounting
toconcrete wall coveredwith plaster/drywall is
unavoidable,plaster/drywall (up to5/8" thick) must be
counterboredas shown below.Be sure concrete
anchorsdo not pullaway from concretewhen tighten-
ing screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
WARNING
AA
DD
6 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down.Attach the interface bracket (BB) to the PLPadapter plate (sold separately) using four M10 x
15 mm socket head screws (EE) as shown in figures 2.1 (portrait) or 2.2 (landscape).
2
Installing Interface Bracket
• Tightenscrews so adapterbrackets are firmly attached. Donot tighten with excessive force.Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
WARNING
fig. 2.1
(portrait)
EE
BB
GENERICPLP
ADAPTERPLATE
fig. 2.2
(landscape)
EE
GENERICPLP
ADAPTERPLATE
BB
7 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down.Attach the interface bracket (BB) to the LC adapter plate (sold separately) using four M5
screwsprovided with plateas shown infigures 2.3 (portrait)or 2.4 (landscape).
2
Installing Interface Bracket to LC Adapter Plate
• Tightenscrews so adapterbrackets are firmly attached. Donot tighten with excessive force.Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
WARNING
fig. 2.3
(portrait)
BB
GENERICLC
ADAPTERPLATE
fig. 2.4
(landscape)
GENERICLC
ADAPTERPLATE
BB
M5SCREWS M5SCREWS
8 of 8 ISSUED: 10-31-05 SHEET #: 202-9011-2 01-29-07
©2005PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkandSmartmountisatrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Mounting and Removing Flat Panel Screen
Note:Security screw may need to be loosened to avoid interference with wall plate.
Hook interface bracket (BB) onto wall plate (AA). Then slowly swing screen in as shown. Turn security screw,using
security allen wrench (FF), clockwise at least six times to prevent screen from being removed as shown in detail 1.
Screen can be adjusted horizontally if desired.
Note: To lock the screen down, tighten security screw to wall plate using security allen wrench as shown in detail 1.
Toremove screen from mount, loosen security screw,swingscreenawayfrommount,andliftscreen offofmount.
3
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING
DETAIL 1
SECURITY
SCREW
BB
BB
AA
Table of contents
Other PEERLESS Rack & Stand manuals
PEERLESS
PEERLESS PLC Guide
PEERLESS
PEERLESS DS-VW760 and assembly Guide
PEERLESS
PEERLESS HDS-S Guide
PEERLESS
PEERLESS PWS211 Guide
PEERLESS
PEERLESS PED 410 Guide
PEERLESS
PEERLESS CMJ 470W Guide
PEERLESS
PEERLESS SmartMount SF650 Guide
PEERLESS
PEERLESS Vision Point LCFS 100 Guide
PEERLESS
PEERLESS FPZ-600 Guide
PEERLESS
PEERLESS Paramount PC930A Guide
PEERLESS
PEERLESS WSP700 Instruction Manual
PEERLESS
PEERLESS WBK100-W Guide
PEERLESS
PEERLESS SR1G Guide
PEERLESS
PEERLESS Paramount PP730 and assembly Guide
PEERLESS
PEERLESS LCC 18-C Guide
PEERLESS
PEERLESS PANA-85WM Guide
PEERLESS
PEERLESS WMJ 018 Guide
PEERLESS
PEERLESS PLA 50-UNL Guide
PEERLESS
PEERLESS MOD-FPSKIT150 Instruction Manual
PEERLESS
PEERLESS MIS 213 Guide
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
