Peerless-AV SmartMount ST16D Guide

Max Load Capacity: 200 lb (91 kg)

Installation and Assembly:

Dedicated Tilt Wall Mount

Model: ST16D

ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

2 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Note: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 5/16" bit for concrete and cinder block wall

• 5/32" bit for wood stud wall

• level

• 6 mm allen wrench

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

call Peerless customer care at 1-800-865-2112.

• This product should only be installed by a qualiﬁed professional.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity of 200 lb (91 kg).

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

WARNING

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Single Stud Wall ...............................................................................................................................................4

Installation to Double Wood Stud Wall ...................................................................................................................................5

Installation to Solid Concrete or Cinder Block ........................................................................................................................6

Attaching PLP Adapter Plate to Tilt Bracket Assembly ...........................................................................................................7

Attaching LC Adapter Plate to Tilt Bracket Assembly .............................................................................................................8

Mounting and Removing Flat Panel Screen...........................................................................................................................9

Adjusting the Tilt Angle of the Flat Panel Screen................................................................................................................. 10

Accessories

•Metal Stud Fastener Kit (ACC 415)

3 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Description Qty Part #

tilt bracket assemby 1 200-0936

Bwall plate 1 200-1797

C#14 x 2.5" wood screw 4 5S1-015-C03

Dconcrete anchor 4 590-0320

EM10 x 15 mm socket head screw 4 520-9262

F4 mm security allen wrench 1 560-1146

Parts List

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

4 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Installation to Single Wood Stud Wall

Use a stud ﬁnder to locate the edges of the stud. Use of an edge-to-edge stud ﬁnder is highly recommended.

Based on its edges, draw a vertical line down the stud’s center. Place wall plate (B) on wall as a template, making

sure that the three mounting holes are over the stud centerline. The top mounting hole should be 2.5" above the

desired screen center as shown in ﬁgure 1.1. Level plate, and mark the center of the three holes. Drill three 5/32"

(4 mm) dia. holes 2-1/2" (64 mm) deep. Make sure that the wall plate is level, secure it using three #14 x 2.5" wood

screws (C) as shown in ﬁgure 1.2.

Skip to step 2 on page 7.

ﬁg. 1.1

ﬁg. 1.2

2.5"

(64 mm)

CS = center of screen

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

5 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Installation to Double Wood Stud Wall

Wall plate (B) can be mounted to two studs that are 16" apart. Use a stud ﬁnder to locate the edges of the studs.

Use of an edge-to-edge stud ﬁnder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired

screen center as shown in ﬁgure 1.3. Level plate, and mark the center of the four mounting holes. Make sure that

the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (64 mm) deep. Make sure

that the wall plate is level, secure it using four #14 x 2.5" wood screws (C) as shown in ﬁgure 1.4.

Skip to step 2 on page 7.

ﬁg. 1.4

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

ﬁg. 1.3

2.5"

(64 mm)

CS = center of screen

6 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Make sure that wall plate (B) is level, use it as a

template to mark four mounting holes. The top

mounting hole should be 2.5" above the desired

screen center as shown in ﬁgure 1.1 on page 4. Drill

four 5/16" (8 mm) dia. holes to a minimum depth of

2.5" (64 mm). Insert anchors (D) in holes ﬂush with

wall as shown (right). Place wall plate over anchors

and secure with #14 x 2.5" screws (C). Level, then

tighten all fasteners.

Installation to Solid Concrete or Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

Drill holes and insert anchors (D).

Place plate (B) over anchors (C) and secure with screws (D).

Tighten all fasteners.

concrete

surface

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable,

the ﬁnishing surface must be counterbored as

shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16 mm), custom

fasteners must be supplied by installer.

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

solid concrete cinder block

7 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Attach adapter bracket to interface bracket of tilt bracket assembly (A) using four M10 screws (E).

Note: Full tilt bracket assembly not shown for clarity.

Skip to step 3.

Attaching PLP Adapter Plate to Tilt Bracket Assembly

Note: Refer to accompanying instruction sheet for attachment of adapter plate to screen before proceeding with step 2.

ADAPTER PLATE

(NOTE: INTERFACE

BRACKET SHOWN

WITHOUT FULL TILT

BRACKET ASSEMBLY

FOR CLARITY)

8 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen.

Place screen face side down. Attach the interface bracket of tilt bracket assembly (A) to the LC adapter plate (sold

separately) using four M5 screws provided with plate as shown.

Attaching LC Adapter Plate to Tilt Bracket Assembly

GENERIC LC ADAPTER PLATE

M5 SCREWS

Note: Refer to accompanying instruction sheet for attachment of adapter plate to screen before proceeding with step 2.

• Tighten screws so interface bracket is ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

WARNING

(NOTE: INTERFACE

BRACKET SHOWN

WITHOUT FULL TILT

BRACKET ASSEMBLY

FOR CLARITY)

9 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Mounting and Removing Flat Panel Screen

Hook tilt bracket assembly (A) onto wall plate (B). Then slowly swing screen in as shown. To lock the screen down,

tighten security screw to wall plate using security allen wrench (F) as shown in detail 1.

If mount is attached to double wood stud, solid concrete, or cinder block wall, screen can be adjusted horizontally if

desired. If mount is attached to single wood stud wall, screen must be centered on wall plate (B).

To remove screen from mount, loosen security screws, swing screen away from mount, and lift screen off of mount.

DETAIL 1

SECURITY

SCREWS

• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.

WARNING

10 of 11 ISSUED: 09-15-05 SHEET #: 202-9031-3 08-18-11

Adjust tension knob on right side of mount shown in

detail 2 to desired tension to balance your screen

size and weight.

Push or pull from top or bottom of screen to adjust

tilt as shown in ﬁgure 4.1. The tilt can be adjusted to

a maximum of 15° forward or 5° backward.

Note: To lock the screen into the desired tilt

position, tighten tension screws on both sides of

mount shown in ﬁgure 4.2 and detail 3 using wrench

(F).

ﬁg 4.1

DETAIL 2

Adjusting the Tilt Angle of the Flat Panel Screen

All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

2300 White Oak Circle

Aurora, Il 60502

www.peerlessmounts.com

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

• Be careful not to pinch ﬁngers when pushing screen

from the bottom.

CAUTION

TENSION

KNOB

TENSION

SCREW

ﬁg 4.2

DETAIL 3

Table of contents

Other peerless-AV Rack & Stand manuals

peerless-AV

peerless-AV ACC-CSH2 User manual

peerless-AV

peerless-AV IRTO49-200 User manual

peerless-AV

peerless-AV SMARTMOUNT SF650 User manual

peerless-AV

peerless-AV SR598E User manual

peerless-AV

peerless-AV SR598ML3T User manual

peerless-AV

peerless-AV KIP540B-3 User manual

peerless-AV

peerless-AV KIP542B User manual

peerless-AV

peerless-AV EWL-OH75F User manual

peerless-AV

peerless-AV PLAV 70-UNL Guide

peerless-AV

peerless-AV KIL540 User manual

peerless-AV

peerless-AV SR860 User manual

peerless-AV

peerless-AV ACC-MB08 User manual

peerless-AV

peerless-AV ACC310 Guide

peerless-AV

peerless-AV SR555E User manual

peerless-AV

peerless-AV HT642-003 Guide

peerless-AV

peerless-AV MOD-CPI User manual

peerless-AV

peerless-AV PRG Series User manual

peerless-AV

peerless-AV SR575M User manual

peerless-AV

peerless-AV HLG440-LG(-Q10) User manual

peerless-AV

peerless-AV MOD-CPI User manual

peerless-AV

peerless-AV PLA 60-UNL-S Guide

peerless-AV

peerless-AV MOD-WP2 User manual

peerless-AV

peerless-AV DS-LEDIF Series User manual

peerless-AV

peerless-AV PA762 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

peerless-AV SmartMount ST16D Guide

Popular Rack & Stand manuals by other brands