Peerless-AV B-MIS38426 User manual

12019-08-26 #:090-9217-1

ENG

60 lb

(27 kg)

MAX

B-MIS38426

For Samsung Super Ultra Wide Curved Monitor

43": LC43J890DKNXZA

49": C49HG90DMN

49": LC49J890DKNXZA

22019-08-26 #:090-9217-1

Symbols

ENG

WARNING

ENG #

Skip to step.

ENG x3

Screws must get at least three

full turns and t snug.

ENG

Display center.

ENG

Do not overtighten screws.

ENG

Tools Needed for Assembly.

ENG

3/8"

(10mm)

ENG To properly tighten screws: Tighten until screw

head makes contact, then tighten another 1/2

turn. Do not overtighten screws.

+1/2

ENG - Before installing make sure the supporting surface will support the combined load of the equipment and

hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.

Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift

and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please

call customer care at 1-800-865-2112.

WARNING

Listen

ENG

17/64" 5/8", 7/16"

3/32" 2"-3"

32019-08-26 #:090-9217-1

A (1)

E (1)

desktop swivel base

support tube

Parts (Before beginning, make sure you have all parts shown below).

ENG

Parts List

Part #Description Qty

Adesktop swivel base 1 090-1821

Badaptor bracket 2 091-1211

Cright adaptor bracket 2 091-1217

Dleft adaptor bracket 2 091-1218

Esupport tube 1 091-1221

FM6 x 6mm hex set screw 2 510-9150

GM4 x 10mm socket pin screw 8 520-1060

Hslope nut 3 530-0035

I1/4-20 x 3/4" washer head screw 4 520-1321

J1/4" x 1/2" x .068 split washer 4 540-9402

K4mm allen wrench 1 560-9646

L48" foam strip 1 570-1170

M1/4-20 lock nut 4 530-1021

Nfender washer 4 540-1008

O1/4-20 x 3" threaded rod 4 520-2585

Pbase plate 1 090-1544

Qthrust washer 1 590-1287

R1/4-20 x 1.5" threaded rod 4 520-2250

S3mm allen wrench 1 560-0194

T10-32 x 1/2" set screw 2 520-1614

D (2)

C (2)

B (2)

adaptor bracket right adaptor bracket left adaptor bracket

L (1)

48" foam strip

K (1)

4mm allen wrench

J (4)

1/4" x 1/2" x .068 split washer

I (4)

1/4-20 x 3/4" washer

head screw

G (8)

M4 x 10mm socket pin

screw

F (2)

M6 x 6mm hex set

screw

S (1)

3mm allen wrench

42019-08-26 #:090-9217-1

Q (1)

thrust washer

H (3)

slope nut

P (1)

base plate

O (4)

1/4-20 x 3" threaded rod

N (4)

fender washer

M (4)

1/4-20 lock nut

R (4)

1/4-20 x 1.5" threaded rod

T (2)

10 x 32mm x 1/2"

hex set screw

52019-08-26 #:090-9217-1

ENG - Wooden mounting surface requires a minumum of 3/4" thickness to hold screen securely.

WARNING

Use base plate as a

template to mark location

of holes. Drill four holes in

square formation, aligned

to front of desk.

Threaded rods

must fasten a

minimum of three

turns.

ENG

22-1

O (4)

Drill 2" to 3" cord

managment hole in the

center of the square

formation.

1-1

Turn base

upside down.

ENG

ENG ENG

17/64"

OR R (4)

Front of desk

ENG Front of desk

ENG

2"-3"

62019-08-26 #:090-9217-1

60°

0°

120°

180°

210°

240°

30°

60°

0°

120°

180°

40°

240

240°

40°

210°

240°

40°

Swivel restriction: refer to detail 1 through 4. Fasten two set screws

where indicated below to the outside of desired angle in steel base.

Note: set screws must be bottomed out into base.

ENG

Front

ENG

3/32"

Detail 1

Detail 2

Detail 3

Detail 4

72019-08-26 #:090-9217-1

4-1

ENG - Make sure that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

WARNING

ENG - Installations to desktops that have a gap between two supporting boards are not acceptable mounting

surfaces for the desktop swivel mount.

CAUTION

M (4)

N (4)

Align plate with threaded rods.

Note: Washer must be centered.

ENG

Align base assembly with

supporting surface and base

pattern facing the front as

shown. Tighten four fender

washers with four lock nuts

in the sequenced pattern

at minimum ush with the

bottom of the threaded rods.

ENG

Front

ENG Front

ENG

7/16"

(11mm)

82019-08-26 #:090-9217-1

Bottom of desk

ENG

5-2

Bottom of desk

ENG Bottom of desk

ENG

Leave space

between

slope nuts.

ENG

Tightening

slope nut

ENG

Optional: for added security replace two of the

washers and locknuts with slope nuts. Hand

tighten slope nuts onto two of the threaded rods

until snug against bottom of desk as shown.

ENG

Insert an open end wrench

between both slope nuts and tighten as shown.

After top slope nut is secure remove bottom slope

nut as shown.

ENG

5-1

5-3

After slope nut is

secure, remove bottom

slope nut as shown.

ENG

5/8"

Thread another slope nut upside-down,

about two turns from rst slope nut as

shown. Avoid jamming both slope nuts

together, doing so may make it di󰀩cult

to remove slope nut used for tightening.

ENG

92019-08-26 #:090-9217-1

66-1

6-2

B (2)

J (4)

F(2)

3/8"

(10mm)

I (4)

10 2019-08-26 #:090-9217-1

Note orientation of tab

ENG

Bottom display

ENG

Top display

ENG

Note orientation of tab

ENG

7-1

Samsung Super Ultra Wide Curved Monitor

43" (LC43J890DKNXZA), 49" (C49HG90DMN), 49" (LC49J890DKNXZA)

sold separately

ENG

Table of contents

Other peerless-AV Rack & Stand manuals

peerless-AV

peerless-AV EWL-49XE4F User manual

peerless-AV

peerless-AV 0735029275640 User manual

peerless-AV

peerless-AV ACC-SPARK55 User manual

peerless-AV

peerless-AV MOD-WP2 User manual

peerless-AV

peerless-AV SmartMount SF640-HUB2 User manual

peerless-AV

peerless-AV MOD-FPSKIT User manual

peerless-AV

peerless-AV SMARTMOUNT XT SFX645P User manual

peerless-AV

peerless-AV DST995 Instruction manual

peerless-AV

peerless-AV PLP-V2X2 Guide

peerless-AV

peerless-AV DS-LEDFLAAF-3X3 User manual

peerless-AV

peerless-AV SMARTMOUNT ST660 User manual

peerless-AV

peerless-AV MOD-FPS2KIT150 User manual

peerless-AV

peerless-AV SUA737 Guide

peerless-AV

peerless-AV IM760P User manual

peerless-AV

peerless-AV SUA746PU User manual

peerless-AV

peerless-AV DS-VW795-QR Guide

peerless-AV

peerless-AV PRSS-1 User manual

peerless-AV

peerless-AV DS-VW765-LAND User manual

peerless-AV

peerless-AV PPA User manual

peerless-AV

peerless-AV SUA751PU User manual

peerless-AV

peerless-AV FPZ-670 Guide

peerless-AV

peerless-AV DCS400 User manual

peerless-AV

peerless-AV PR560M User manual

peerless-AV

peerless-AV SMART MOUNT LT SAL746 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

peerless-AV B-MIS38426 User manual

Popular Rack & Stand manuals by other brands