Parker AC890PX Series User manual

User Mounting and Assembly Instructions

HM501225U001 Issue 3

Page 2 - 30

Parts List:

Chassis Assembly

LA501088UXXX

CS Module Control Cable

CM471462U002

STO PCB

AH471776U001

CP to CS Control Cable

CM471686U003

AC890PX Control Module

890CM

Blanking plates

LA501357U001

BA501301U002

BA501301U003

AC890 CS Module

LA471171UXXX

(optional)

Bracket x 2

BA501090

AC890 CD Module

LA471160UXXX x 3

Housing Bracket

BA501111

BA501112

AC890 CP module

LA471175UXXX

(optional)

Air duct

BA501114

BA501113

STO Feedback Cable

CM472271U002

Roof Vent

LA501358

STO Supply Cable

CM501215U001

Mounting Bracket

BA501092 x 2

STO connection Cable

LA501221

Mounting Bracket

BA501093

Module Control Cables

CM471297U002

CM471297U003

CM471297U004

Upper & Lower

Setting Plates

BA501120

Earth Wire Assembly

CM467679U001

TS8 Adaptor

BA501091 x 2

Module Power Cables

CM501601U100

CM501601U500

Also Included:

Grommets, screws, p clips, gasket strip, etc.

CM501600U200

CM501600U300

CM501600U400

Right & Left Side Panels

LA501220U001

LA501220U002

See page 23

(drawing no.

LA501088U000)

Page 3 - 30

Before starting assembly you must read the Safety Instructions at the

beginning of Product Manual HA501299U001 available from

www.parker.com/ssd.

1. Assemble cubicle ready for mounting AC890PX Frame M.

Notes:

The minimum required backpanel width is 600mm.

This product is intended to be mounted in an appropriate electrical enclosure in a vertical

position where it is not subject to excessive heat or vibration.

These instructions use a Rittal TS8 cubical. If the product is not to be mounted in a Rittal

cubical then refer to HG501237U001.

These instruction need to be used in conjunction with assembly drawing LA501088U000.

Co-ordinates for a Rittal TS8 or PS8 series 600mm back panel HG501140.

Punch or drill the required mounting holes into the cubicle backplate this drawing assumes

the use of M8 inserts.

The back panel must be mounted in the rear most position.

Page 4 - 30

2. Fit STO PCB Assembly AH471776U001 to retaining posts on the chassis.

This equipment contains electrostatic discharge (ESD) sensitive parts. Observe

static control precautions when handling, installing and servicing this product.

3. Mount the chassis into the cubicle.

Partially insert a M8 bolt (no washer) in the centre top

mounting hole.

Hang the chassis assembly from the single bolt by passing the bolt head through the large

central hole on the rear panel of the chassis. Chassis is 38kg thus lifting procedures must

be adhered to.

Fix to back panel in all 4 positions with M8

bolts and remove original hanging bolt.

Page 5 - 30

4. Install the module mounting rails. Use the top dowels to align and fit left (LA501220U001)

and right (LA501220U002) rail assembles, fix using M5 SEMs FY047651 (item 642), quantity

8 (torque setting 2.7Nm).

5. Fit lower left mounting bracket BA501092 (item 252) with M6 SEMs FY385692 (item 643),

quantity 4 (torque setting 4.5Nm).

Fixings

BA501092

Fixings

Page 6 - 30

6. Loosely fit TS8 adaptor bracket BA501090 (item 250) to lower left mounting bracket

BA501092 (item 252) with M6 SEMs FY385692 (item 643), quantity 2. Loosely fit to cubicle

frame using TORX self tap screws FY501218 (item 645), quantity 2 (use upper hole positions)

(torque setting 4.5Nm).

7. Fit lower right mounting bracket BA501093 (item 253) with M6 SEMs FY385692 (item 643),

quantity 4 (torque setting 4.5Nm).

BA501090

BA501093

Fixings

Page 7 - 30

8. Loosely fit TS8 adaptor bracket BA501091 (item 251) to lower right mounting bracket

BA501093 (item 253) with M6 SEMs FY385692 (torque setting 4.5Nm) (item 643), quantity 3.

Loosely fit to cubicle frame using TORX self tap screws FY501218 (torque setting 2.7Nm)

(item 645), quantity 2 (use upper hole positions).

9. Fit lower setting plate BA501120 (item258) with self tap screws FY501150 (item 640),

quantity 6.

Tighten screws on TS8 adaptor bracket BA501091 (item 251) and TS8 adaptor bracket

BA501090 (item 250), on right and left sides, quantity 5. Tighten TORX self tap screws

FY501218 (item 645) slots towards the back, on both left and right sides, quantity 6.

Slots

Fixings

Page 8 - 30

10. Fit upper left mounting bracket BA501092 (item 252) with M6 SEMs FY385692 (torque

setting 4.5Nm) (item 643), quantity 4. Fix earth wire assembly CM467679U001 (item 285)

with front top screw, as shown.

Fit control housing bracket BA501111 (item 259) to left mounting bracket BA501092 (item

252) with M4 SEMs FY385968 (item 644), quantity 2.

Add grommet DF044535 (item 431) to mounting bracket BA501092 (item 252), this grommet

only has wires passing through it when it is configured as a parallel stack.

11. Loosely fit TS8 adaptor bracket BA501090 (item 250) to upper left mounting bracket

BA501092 (item 252) with M6 SEMs FY385692 (item 643), quantity 2. Loosely fit to cubicle

frame using TORX self tap screws FY501218 (item 645), quantity 2 (use lower hole

positions).

CM4674679U001

BA501090

Page 9 - 30

12. Fit upper right mounting bracket BA501093 (item 253) with M6 SEMs FY385692 (item

643), quantity 4. Fit control housing bracket BA501112 (item 260) to upper right mounting

bracket BA501093 (item 253) with M4 SEMs FY385968 (torque setting 1.3Nm) (item 643),

quantity 2.

13. Loosely fit TS8 adaptor bracket BA501091 (item 251) to upper right mounting bracket

BA501093 (item 253) with M6 SEMs FY385692 (item 643), quantity 3. Loosely fit to cubicle

frame using TORX self tap screws FY501218 (item 645), quantity 2 (use lower hole

positions).

BA501092

BA501091

Page 10 - 30

14. Fit upper setting plate BA501120 (item 258) with self tap screws FY501150 (item 640),

quantity 6 (slots to the rear).

Tighten screws on TS8 adaptor bracket BA501091 (item 251) and TS8 adaptor bracket

BA501090 (item 250), quantity 5. Tighten TORX self tap screws FY501218 (torque setting

2.7Nm) (item 645) on both sides, quantity 4.

BA501120

Other manuals for AC890PX Series

Table of contents

Other Parker Controllers manuals

Parker

Parker 650V series User manual

Parker

Parker GEM6K Series Manual

Parker

Parker Lucifer EPP4 Series User instructions

Parker

Parker Hauser COMPAX-S Series User manual

Parker

Parker 514C-04 User manual

Parker

Parker X-Flow Quick start guide

Parker

Parker Gemini GV6K Series User manual

Parker

Parker 690+ series User manual

Parker

Parker Lucifer EPP4 P4BG4 Series User instructions

Parker

Parker 598P Instructions for use

Parker

Parker ACR Series Manual

Parker

Parker XLT Series Datasheet

Parker

Parker ADAPTOMODE A4A Series Guide

Parker

Parker PAC120 Series User manual

Parker

Parker TQ10X User manual

Parker

Parker 6250 User manual

Parker

Parker AC890PX Series User manual

Parker

Parker Aries AR-04CE User manual

Parker

Parker Sporlan Kelvin II Series User manual

Parker

Parker 700-00027-0 User manual

Parker

Parker A4AP-DN Manual

Parker

Parker Sporlan S3C User manual

Parker

Parker LevelController SCLSD User manual

Parker

Parker Compax3 Fluid T40 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual