Onkyo TX-RZ710 Installation guide
Basic Manual
Hookup
Step1: Choose your Speaker Layout .......................................3
Step2: Connect the Speakers ..................................................9
Step3: Connect the TV ..........................................................11
Step4: Connect the AV Components .....................................13
Step5: Multi-zone Connection ...............................................16
Step6: Connect Other Cables ................................................19
Setup
Step7: Power On & Initial Setup ............................................20
HDMI Setup ...........................................................................21
Playback
Basic Playback ......................................................................22
Network Functions .................................................................23
Others ....................................................................................25
Part Names
Front Panel ............................................................................27
Rear Panel ............................................................................28
Remote Controller .................................................................29
Display ...................................................................................29
This manual includes information needed when starting up and also
instructions for frequently used operations. The "Advanced Manual" is
available on the internet with details about the playback features/
listening modes/settings details, specifications, and troubleshooting.
The Advanced Manual is created in a format that makes it easy to read
on a PC or Smartphone.
http://www.onkyo.com/manual/txrz710/adv/en.html
Advanced Manual found here
AV RECEIVER
TX-RZ710
> Before start > Hookup > Setup > Playback > Part Names
SN29402172_TX-RZ710_BAS_En.book 1 ページ ２０１６年２月１７日 水曜日 午後７時２５分
2
> Before start > Hookup > Setup > Playback > Part Names
What's in the box
1. Main unit 2. Remote controller (RC-911R)
×1, Batteries (AAA/R03) ×2
3. Indoor FM antenna ×1 4. AM loop antenna ×1 5. Speaker setup microphone ×1
6. Power cord ×1
Main features
This unit is connected between your TV and your AV components. To play, select the source with the input
selector. You can connect 7.1ch of speakers to this unit, with 7ch at 180 W (6 ohms, 1 kHz, 0.9%THD) (North
American models) / 175 W (6 ohms, 1 kHz, 1%THD) (European, Australian and Asian models) per channel plus
pre out jack for powered subwoofer.
$Conforms to the THX Select2 Plus specification: THX is a series of specifications for the accurate reproduction
of movies propounded by the film director George Lucas. This unit is equipped with a variety of THX technology
to faithfully reproduce according to the sound design envisaged by the movie producer, including surround
modes that take account of factors such as the size and number of speakers, and the differences in
environments between home theaters and movie theaters.
$Supports playback in Dolby Atmos format which provides 360e sound placement
$The HDMI jack supports 4K video input and output. Jacks IN1 to 3 and OUT MAIN/SUB support HDCP2.2
$HDMI CEC functionality: Control features such as linking input switching with the input selector and players
conforming to the CEC standard, switching audio output and volume using the remote controller of a CEC-
compliant TV, and automatically switching this unit to standby when the TV is turned off
$
HDMI Standby Through: Video and audio signals from AV components can be transmitted to the TV even if this unit is in standby
$ARC: Connection with an ARC-compatible TV is complete with one HDMI cable
$Easy Initial Setup using onscreen guidance and On-Screen Display (OSD) showing operations on the TV
$Internet radio and AirPlay via wired LAN or Wi-Fi (wireless LAN) and network features such as Music Server
that enables PC music file playback, USB playback, plus other playback features such as AM/FM radio and
BLUETOOTH
®
play
$Playback formats supported by Music Server and USB include WAV, FLAC and DSD high-res source
$Multi-zone Connection which allows you to play in the main room and listen in a separate room (ZONE 2)
$Equipped with RS232 port, IR IN jack, and 12V TRIGGER OUT jack
$We plan to provide support for the DTS:X audio format through a firmware update for this unit. Refer to our
website for more information.
CAUTION:
Connect speakers with 6 Ω to 16 Ω impedance. When connecting speakers to both ZONE 2A and
ZONE 2B (North American models) (
P18), both sets of speakers connected in ZONE 2 should have 8 Ω to
16 Ω impedance. The power cord must be connected only after all other cable connections are completed.
0We will not accept responsibility for damage arising from the connection of equipment manufactured by
other companies.
1
2
56
34
(For North American,
European and Asian
models)
SN29402172_TX-RZ710_BAS_En.book 2 ページ ２０１６年２月１７日 水曜日 午後７時２５分
3
> Before start > Hookup >Setup >Playback >PartNames
Step1: Choose your Speaker Layout
12
Front Speakers
3
Center Speaker
45
Surround Speakers
6
Powered Subwoofer
For 5.1-Channel System
This is a 5.1-channel system that is the basic surround
system. Front speakers output front stereo sound and a
center speaker outputs center sound such as dialogs and
vocals. Surround speakers create back sound field.
Powered subwoofer reproduces bass sounds and creates
rich sound field. The front speakers should be positioned
at ear height, while the surround speakers should be
positioned just above ear height. Center speaker should
be set up facing the listening position. Place the powered
subwoofer towards the front. Placing it between the center
speaker and a front speaker gives you a natural sound
even when playing music.
0The front speakers, center speaker, and surround
speakers are counted as 5 channels, and the powered
subwoofer is counted as 0.1 of a channel, giving us the
name 5.1ch system.
＊1: 22e to 30e, ＊2: 120e
Go To "Hookup" (
P9)
＊1
＊2
SN29402172_TX-RZ710_BAS_En.book 3 ページ ２０１６年２月１７日 水曜日 午後７時２５分
4
> Before start > Hookup >Setup >Playback >PartNames
16
(
P3)
78
Surround Back Speakers
For 7.1-Channel System (with
Surround Back Speakers)
This is a system with surround back speakers added to
the basic 5.1-channel system. The connection of surround
back speakers improves the sense of envelopment and
connectivity of sound created by the back sound field and
provides a more real sound field. You can select the Dolby
Atmos listening mode, which realizes the most up-to-date
3D surround sound, when the input format is Dolby
Atmos. With formats other than Dolby Atmos, you can still
create a sound field by outputting sound from the
surround back speakers when you select the Dolby
Surround listening mode. The optimal positioning is for
surround back speakers to be at ear height. Place the
surround speakers in a more slightly forward position than
you would in a 5.1-channel system.
0If you are including surround back speakers in the
setup, surround speakers are required.
＊1: 22e to 30e, ＊2: 90e to 110e, ＊3: 135e to 150e
Go To "Hookup" (
P9)
＊2
＊3
＊1
SN29402172_TX-RZ710_BAS_En.book 4 ページ ２０１６年２月１７日 水曜日 午後７時２５分
5
> Before start > Hookup >Setup >Playback >PartNames
3´ (0.9 m)
or more
16
(
P3)
78
Height Speakers
Choose one of the following:
$
$
Front High Speakers
Rear High Speakers
For 7.1-Channel System
(with Height Speakers-A)
Front High or Rear High speakers
This is a basic 5.1-channel system with the addition of
height speakers, either as front high speakers or rear high
speakers. Select which speakers to setup according to
the environment of the room. You can select the Dolby
Atmos listening mode (5.1.2 channel playback), which
realizes the most up-to-date 3D surround sound including
overhead sounds, when the input format is Dolby Atmos.
With formats other than Dolby Atmos, you can still create
a sound field by outputting sound from the height
speakers when you select the Dolby Surround listening
mode. Front high speakers or rear high speakers should
be situated at least 0.9 m higher than the front speakers.
Front high speakers should be situated directly above the
front speakers and the distance between the rear high
speakers should match the distance between the front
speakers. Both should be set up facing the listening
position.
＊1: 22e to 30e, ＊2: 120e
Go To "Hookup" (
P9)
＊1
＊2
SN29402172_TX-RZ710_BAS_En.book 5 ページ ２０１６年２月１７日 水曜日 午後７時２５分
6
> Before start > Hookup >Setup >Playback >PartNames
16
(
P3)
78
Height Speakers
Choose one of the following:
$
$
$
Top Front Speakers
Top Middle Speakers
Top Rear Speakers
For 7.1-Channel System
(with Height Speakers-B)
Ceiling speakers
This is a basic 5.1-channel system using ceiling speakers,
for example, with the addition of height speakers, either
as top front speakers, top middle speakers, or top rear
speakers. Select which speakers to setup according to
the environment of the room. You can select the Dolby
Atmos listening mode (5.1.2 channel playback), which
realizes the most up-to-date 3D surround sound including
overhead sounds, when the input format is Dolby Atmos.
With formats other than Dolby Atmos, you can still create
a sound field by outputting sound from the height
speakers when you select the Dolby Surround listening
mode. Fit top front speakers on the ceiling forward of the
seating position, top middle speakers on the ceiling
directly above the seating position, and top rear speakers
on the ceiling behind the seating position. The distance
between each pair should match the distance between
the two front speakers.
0Dolby Laboratories recommends placing this type of
height speakers to obtain the best Dolby Atmos effect.
＊1: 30e to 55e, ＊2: 65e to 100e, ＊3: 125e to 150e
Go To "Hookup" (
P9)
＊1
＊2
＊3
SN29402172_TX-RZ710_BAS_En.book 6 ページ ２０１６年２月１７日 水曜日 午後７時２５分
7
> Before start > Hookup >Setup >Playback >PartNames
16
(
P3)
78
Height Speakers
Choose one of the following:
$
$
Dolby Enabled Speakers (Front)
Dolby Enabled Speakers (Surround)
For 7.1-Channel System
(with Height Speakers-C)
Dolby enabled speakers
This is a basic 5.1-channel system using Dolby enabled
speakers, with the addition of height speakers, either as
Dolby enabled speakers (front) or Dolby enabled
speakers (surround). Select which speakers to setup
according to the environment of the room.
Dolby enabled speakers are special speakers designed to
face the ceiling so that sound is heard after bouncing off
the ceiling so that sound appears to be coming from
overhead. You can select the Dolby Atmos listening mode
(5.1.2 channel playback), which realizes the most up-to-
date 3D surround sound including overhead sounds,
when the input format is Dolby Atmos. With formats other
than Dolby Atmos, you can still create a sound field by
outputting sound from the height speakers when you
select the Dolby Surround listening mode. Place them
either above the front speakers or above the surround
speakers.
＊1: 22e to 30e, ＊2: 120e
Go To "Hookup" (
P9)
＊1
＊2
SN29402172_TX-RZ710_BAS_En.book 7 ページ ２０１６年２月１７日 水曜日 午後７時２５分
8
> Before start > Hookup >Setup >Playback >PartNames
12
Front Speakers (Bi-Amping)
3
Center Speaker
45
Surround Speakers
6
Powered Subwoofer
For Bi-Amping the
Speakers
It is possible to connect front speakers supporting Bi-
Amping to improve quality of the bass and treble. The
maximum number of channels available with this
connection is 5.1 because Bi-Amping speakers require
one amplifier for the tweeter jacks and one amplifier for
the woofer jacks. The effects and placements for
speakers are the same as the 5.1-channel plan that
doesn't use Bi-Amping speakers.
0You cannot output to ZONE 2 SPEAKER (
P18) if the
speakers have been connected for Bi-Amping.
＊1: 22e to 30e, ＊2: 120e
Go To "Hookup" (
P10)
＊1
＊2
SN29402172_TX-RZ710_BAS_En.book 8 ページ ２０１６年２月１７日 水曜日 午後７時２５分
9
> Before start > Hookup >Setup >Playback >PartNames
Step2: Connect the Speakers
2
1
1/2˝
(12 mm)
1 Speaker cable, 2 Subwoofer cable
in case of:
Pages 3 to 7
Connect 123456 for a 5.1-channel system. For a
7.1-channel system, select either surround back speakers
or height speakers, and connect 78. Up to two powered
subwoofers can be connected. The same signal is output
from each of the SUBWOOFER jacks.
Make sure the exposed wires of the speakers do not stick out of
the speaker terminals when connecting. If the exposed wires of
the speakers touch the rear panel or the + and – wires touch each
other, the protection circuit will be activated.
Setup
0The speaker configuration is set to
12345678 audio output by default. If there
are speakers you won't be connecting, you need to
change the settings in Initial Setup, "1. AccuEQ
Room Calibration" (
P20) so that the audio from
those speakers you are not connecting is sent to
other speakers. Note that if you are using height
speakers, set "Speaker Channels" to "5.1.2 ch" in
the setting screen.
SN29402172_TX-RZ710_BAS_En.book 9 ページ ２０１６年２月１７日 水曜日 午後７時２５分
10
> Before start > Hookup >Setup >Playback >PartNames
1
2
1/2˝
(12 mm)
For high-
frequency
For low-
frequency
1 Speaker cable, 2 Subwoofer cable
in case of:
Page 8
Connect front speakers compatible with Bi-Amping
connection to the FRONT jacks and the SURROUND
BACK or HEIGHT jacks. Make sure you remove the
jumper bar fitted between the woofer jacks and tweeter
jacks of the front speakers. In case of Bi-Amping
connection, refer to the instruction manual of your
speakers. Up to two powered subwoofers can be
connected. The same signal is output from each of the
SUBWOOFER jacks.
Make sure the exposed wires of the speakers do not stick out of
the speaker terminals when connecting. If the exposed wires of
the speakers touch the rear panel or the + and – wires touch each
other, the protection circuit will be activated.
Setup
0Bi-Amping connection requires you to change
some settings. Select "Yes" in "Bi-Amp" in "1.
AccuEQ Room Calibration" (
P20) in the Initial
Setup.
SN29402172_TX-RZ710_BAS_En.book 10 ページ ２０１６年２月１７日 水曜日 午後７時２５分
This manual suits for next models
1
Table of contents
Other Onkyo Receiver manuals
Onkyo
Onkyo TX-SR805 Administrator guide
Onkyo
Onkyo HT-RC560 Parts list manual
Onkyo
Onkyo TX-8050 Mounting instructions
Onkyo
Onkyo HT-RC360 User manual
Onkyo
Onkyo TX-SV343 User manual
Onkyo
Onkyo HT-R430 User manual
Onkyo
Onkyo HT-R758 User manual
Onkyo
Onkyo TX-SR573 User manual
Onkyo
Onkyo HT-R640 Manual
Onkyo
Onkyo TX-DS484 User manual
Onkyo
Onkyo TX-SR307 User manual
Onkyo
Onkyo TX-DS575X User manual
Onkyo
Onkyo TX-SR577 Specification sheet
Onkyo
Onkyo TX-SR506 Quick start guide
Onkyo
Onkyo HT-RC360 User manual
Onkyo
Onkyo TX-SR501E User manual
Onkyo
Onkyo TX-SR703 User manual
Onkyo
Onkyo TX-NR727 Mounting instructions
Onkyo
Onkyo HT-S3400 User manual
Onkyo
Onkyo TX-RZ3100 User manual
