Oki OKIPAGE 8z Specification sheet

Other manuals for OKIPAGE 8z

4

Table of contents

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide

Quick

Setup

3

2

1Check Contents

Remove the Protective Sheet

Tilt up the image drum and lift it out. Do not

touch image drum’s green surface.

Install the Paper Feed Tray

Before you can use your printer:

q

Steps 1 to 5 - Setup your printer.

q

Step 6 - Install the correct Interface cable for your system—USB or Parallel.

q

Step 7 - Determine your computer’s Operating System—Windows®95, 98, 2000, NT®4.0 or

Macintosh®(OS 8.1 or higher), then install the correct printer software for your computer’s

Operating System and Interface.

q

See the on-line User’s Guide for more information about your printer.

Press down firmly until drum snaps into place.

Ê

Printer

Ë

Paper Feed Tray

Ì

Toner

Í

Power Cord

Î

CD

Ï

Light-Shield Bag (to protect image

drum from light when it is removed

from printer)

➐Quick Setup Instructions

!Interface cable is not included. For

information on cable requirements, see

“Supplies” in the on-line User’s Guide.

Pull out sheet ➊, and remove tape ➋.

If transparent film is attached, remove

film with sheet.

58341901

Lift the cover.

Replace the image drum, tilting it down

to slide under the guides ➊.

➊

➊

➊

➋

Press to lock tray in place.

Align tabs on bottom of paper tray

into slots on back of printer.

Swing tray up and align tabs

and slots at top.

©2000 Oki Data Americas, Inc.

➊

➋

➌

➍

➎

➏

➐

6

4

5

Push lock lever down towards rear.

Insert Paper

Adjust left guide for paper size. Insert a stack of paper. (max. 100 sheets, 20 lb.) Adjust the right guide gently against the paper. Make sure power is off.

Install Toner

Connect to Your Computer

Connecting to a USB Port

For Windows 98/2000 and Macintosh Computers with a USB

port. Requires USB cable.

1Connect the USB cable to the computer’s USB port.

2Connect the other end of the USB cable to the printer’s USB

port.

3Go to Step 7, Install the Printer Software.

Connecting to a Parallel Port

Requires IEEE 1284-compliant bi-directional parallel cable.

1Make sure the computer and printer are turned off.

2Connect the parallel cable to the computer’s parallel port.

Secure the screws.

3Connect the other end of the cable to the printer’s parallel

port. Secure it with the wire clips.

4Go to Step 7, Install the Printer Software.

Plug the power cord into the printer and into a

grounded electrical outlet.

With label up, place left side

under tab ➊, lower into the

toner well. Close the cover.

Unwrap toner cartridge. Shake

side to side to distribute toner.

Lift out toner well cover and discard.

➊

Pulling firmly, remove

tape from bottom.