Oce Fx2081 User manual

DA7-92360-60

The steps to setup the machine

Step 1 : Pick an installation spot.............................................1

Step 2 : Unpack the machine..................................................2

Step 3 : Setup the machine ....................................................3

Step 4 : Install the cartridges ..................................................5

Step 5 : Loading paper ...........................................................7

Step 6 : Connect the cables..................................................10

Step 7 : Turn the power on....................................................12

Step 8 : Turn off the transport mode .....................................13

Step 9 : Initial setup ..............................................................14

Step 10 : Set the paper size .................................................16

Step 11 : Assigning an IP Address .......................................17

Step 12 : Browser-based setup ............................................21

Step 13 : Setup e-mail server ...............................................22

Step 14 : Installing drivers and OfﬁceDirector utilities ..........22

Step 15 : Driver installation for local printing and scanning ..22

1Installation Manual

Step 1 : Pick an installation spot

Space requirement:

33.6 inches (853 mm)

29.6 inches (753 mm)

2 inches

(50 mm) 2 inches

(50 mm)

30.4 inches

(772 mm)

34.3 inches

(872 mm)

4 inches

(100 mm)

28.1 inches

(713 mm)

32.0 inches

(813 mm)

4 inches

(100 mm)

The location should be:

• Clean / Dust free — Dust build-up can damage your machine. (However, do not

use a dust cover!)

• In the open — Allow for adequate space around your machine. Be sure that you

never cover the machine. Its vents must be able to “breathe.”

• Away from direct sunlight — This helps avoid overheating.

• Dry — Avoid any location where splatters or sprays (such as from a water foun-

tain) could reach your machine.

• Level, and vibration free

• Near a phone jack — Your machine uses a standard (modular) telephone jack.

• Near an AC power outlet — The AC power cord is about 6.5 feet (2.0 meter) long

when stretched to its limit. The power cord should never be stretched to its limit.

2Installation Manual

Step 2 : Unpack the machine

Remove all items from the box.

Check that all the following items have been included.

Main unit with 500-sheet paper cassette

AC power cord

Océ fx2081

OfficeDirector

Document tray

Telephone line cable

Ferrite core

Drum cartridge Toner cartridge

Océ sx1481/fx2081

PCL Print Driver

(6)

(8)

(4)

(1) (2) (3) (5)

Documentation & labels

(1) MFP user’s guide

(2) PC user’s guide

(3) Quick reference guide

(4) Installation guide (this book)

(5) Safety information

(6) Paper size label

(7) Mirror carriage caution sheet

(8) Service/Supplies call label

(7)

NOTE

Save the carton and packing material in case there’s a need for reshipment.

3Installation Manual

Step 3 : Setup the machine

Remove all the shipping materials

Open the ADF cover,

then remove the protective sheet

from the ADF.

Remove the protective sheet

between the platen cover and

document glass.

Remove the protective sheet

covering the touch panel.

Open the cassette and remove

the spacer in the paper cassette.

Attach the document tray

Attach the document tray by inserting it into the appropriate holes, as shown

below.

4Installation Manual

Unlock the scanner

IMPORTANT

In order to avoid damaging the unit, the machines scanner is locked prior to

shipping.

If you need to relocate the machine, lock the scanner prior to moving it.

To lock the scanner, please use the reverse process of the instructions below.

1Slide the scanner locking knob to the back until it clicks in the unlocking

position.

2Turn off the transport mode (see Step 8 “Turn off the transport mode,” page

13).

5Installation Manual

Step 4 : Install the cartridges

1Pull the release lever to open the side cover.

2Open the front cover.

3Turn the toner cartridge locking lever to the left (unlock position).

4Unpack the drum cartridge from its carton and slide it into the machine

ﬁrmly until it locks into place.

NOTE

DO NOT touch the photoconductor drum on the drum cartridge.

6Installation Manual

5Unpack the starter toner cartridge, hold it with both hands and gently

shake it to distribute the toner evenly inside the cartridge.

NOTE

Do not touch the roller of the toner cartridge.

6Slide the toner cartridge into the machine ﬁrmly until it locks into place.

Then turn the cartridge locking lever to the right until it locks into place.

7Close the front and side covers.

7Installation Manual

Step 5 : Loading paper

Your machine comes with one standard paper cassette and a bypass tray (one

optional 500 sheet paper cassette is also available separately) that combine

for a total capacity of 550 or 1050 sheets.

Acceptable paper

• Paper cassette

Paper type Paper size Capacity

Plain paper

(Paper weight: 20 to 24 lbs.

(60 to 90 g/m2))

Letter, Legal, Half-letter 500 sheets

(Paper weight: 20 lbs.

(60 g/m2))

• Bypass tray

Paper type Paper size Capacity

Plain paper

(Paper weight: 20 to 24 lbs.

(60 to 90 g/m2))

Letter, Legal, Half-letter , Executive

A4, A5, A5 , A6, F4,

50 sheets

(Paper weight: 20 lbs.

(60 g/m2))

Custom sizes

• Width: 3.8 to 8.5 in. (97 to 216 mm)

• Length: 5.5 to 14 in. (140 to 356 mm)

1 sheet

Envelopes DL: 4.33 × 8.66 in. (110 × 220 mm)

Com#10: 4.125 × 9.5 in. (105 × 241 mm)

Monarch: 3.875 × 7.5 in. (98.4 × 190.5 mm)

1 envelope

Postcard 3.94 × 5.83 in. (100 × 148 mm) 20 sheets

Transparency Letter 20 sheets

NOTE

• Custom-sized paper can be used for PC printing only.

• Do not use envelopes with double ﬂaps or pressure seals since these do not

feed properly.

• If using a transparency (OHP) ﬁlm, be sure that the ﬁlm does not have a

paper backing and/or leading strip. If it does, remove the paper backing and/

or strip before loading. Only the ﬁlm should go in, ﬁlm with paper backing or

a leading strip should not be fed.

Loading paper into the paper cassette

1Pull the handle toward you to open the paper cassette.

8Installation Manual

2Press the paper lifting plate down until it locks into position.

3Adjust the rear paper guide to the desired paper length.

4Load the paper into the cassette.

• Make sure you properly stack the paper prior to setting it in the cassette.

The leading edge and sides should be even.

• Do not stack the paper over the limit mark inside the cassette.

Other manuals for fx2081

Table of contents

Popular All In One Printer manuals by other brands

Triumph Adler

Triumph Adler DC 2016 Instruction handbook

Epson

Epson WorkForce WF-2510 Basic guide

Epson

Epson Stylus Scan 2000 Product information guide

Epson

Epson PictureMate Snap PM 240 Start here

Konica Minolta

Konica Minolta bizhub C35 user guide

Brother

Brother MFC-J430w user guide

Konica Minolta

Konica Minolta BIZHUB 558 Quick reference guide

Lexmark

Lexmark MX710 Series setup sheet

Brother

Brother MFC-9760 owner's manual

Lexmark

Lexmark XC8155 user guide

Lexmark

Lexmark X642E Service manual

Sharp

Sharp MX-2310U Start guide

Aficio

Aficio 200 manual

Canon

Canon ImageCLASS 2300 setup sheet

Ricoh

Ricoh Pro C900 Brochure & specs

Lexmark

Lexmark X925 Installation

Brother

Brother Business Smart MFC-J4510dw manual

Epson

Epson Stylus CX8400 Series Brochure & specs

Oce fx2081 User manual

Popular All In One Printer manuals by other brands