Nuvico Xcel NCT-6M-FE User manual

■Please read these instructions carefully and preserve it for further reference.

■All the examples and pictures used here are for reference only.

■There may be several technically incorrect places or printing errors in this

manual. The update information will be added into the new version of this manual.

The contents of this manual are subject to change without notice.

NCT-6M-FE Fisheye Camera

Quick Start Guide

1Warning and Caution

■If the product does not work properly, please contact your dealer or

the nearest service center. Never attempt to disassemble the camera

yourself. (We shall not be responsible for any problems caused by

unauthorized repair or maintenance.)

■Do not allow water or liquid intrusion into the camera.

■In the use of the product, you must be in strict compliance with the

electrical safety regulations of the nation and region. When the product is

mounted on wall or ceiling, the camera shall be firmly fixed.

■Do not use camera beyond specific voltage range.

■Do not drop the camera or subject it to physical shock.

■Avoid touching the camera lens.

■If cleaning is necessary, please use clean cloth to wipe it gently.

■Do not aim the camera at the sun or extra bright place.

■Do not place the camera in extremely hot, cold (the operating

temperature shall be -22˚F~144˚F), dusty or damp locations, and do not

expose it to high electromagnetic radiation.

■To avoid heat accumulation, good ventilation is required for operating

environment.

■A few parts of the device shall be replaced regularly according to their

average enduring time. Regular checking is recommended for all users.

Overview

21 Ethernet Connector

2 MIC IN

3 HP Audio Output

4 Video Output

5 Alarm Input/Output

6 RS485

7 DC12V Power Supply

8 SD Card Slot

9 Reset

Package

Camera Quick start guide

CD Plastic plug × 3

Drill template Screwdriver

Tapping screws ×3

ALM-COM

ALM-OPEN

ALM-INA

ALM-GND

RS485T+

RS485T-

DC12V

*If a PoE switch is used to power the camera, DC12V power supply is not required.

●

Alarm Input: Join the grounding ends of the sensor and the camera

and then connect the signal cable of the sensor to the alarm input

port (ALM-INA) of the camera.

Alarm Output: Loosen the screws in the alarm output port. Then

insert the signal wires of the alarm output devices into the port of

COM and OPEN separately. Finally tighten the screws. Some of the

external alarm output devices need the power supply.

Connecting Network Cable

Alarm Connection

●

Install SD Card

Please install and use the camera in a dry environment. Install the back

cover in less than 4 hours after removing it.

Gap

Fixed Ring

Installation

①Remove the fixed ring from the gap of the camera.

②Loosen the screws of the cover of the SD card and then insert the

SD card. After that, install the cover back.

①Loosen the nut from the main element.

②Run the network cable (without RJ 45 connector) through both

elements. Then crimp the cable with RJ 45 connector.

③Connect the cable to the hermetic connector. Then tighten the

nut and the main cover.

●

∅5 .12 in

∅3 .54 in

∅ 3/16 in

3.3 in

3.82 in

Before installation, please make sure that the wall is strong enough to

withstand 3 times the weight of the camera.

①Remove the fixed ring from the gap of the camera (see Install

SD Card ① ).

②Drill the screw holes and cut the cable hole (A) in the ceiling

according to the drill template.

③

④Fix the camera to the wall with screws as shown below.

Route and connect the cables.

Hole A: f or cabl e route d throu gh the ce iling

Install Camera

●

⑤Install the fixed ring back to the camera.

①Remove the fixed ring from the gap of the camera (see Install SD

Card ① ).

②Install the junction box onto the wall.

③Route the cables through the cable hole (for example take side conduit

cabling) and connect the cables. Then fix the camera onto the junction box

with screws.

Install Camera with Junction Box

●

④Install the fixed ring back to finish the installation.

Here we take accessing the device via LAN for example. In LAN,

there are two ways to access. 1. Access through Xcel IP Utility;

2. Direct Access through Web Browser

Network Connection

Rubber plug

IPC

Network Cable Network Cable

Switch

Router Computer

•Access through Xcel IP Utility

①Make sure that the camera and the PC are connected via LAN.

②Find the Xcel IP Utility from the CD and then install it in the

computer. After that, run the Xcel IP Utility as shown below.

You may use the above default settings when you log in the camera

for the first time.

Device Network Search

Immediate Refresh

name

IPC

unknown

192.168.226.201

192.168.1.2

192.168.1.3

9008

255.255.

Modify Network Parameter

Mac Address

IP Address

Modify

CE :98 :23 :75 :35 :22

192 .168 . 226 . 201

255 . 255 . 255 . 0

192 .168 . 226 . 1

Tip: Enter the administrator password, and

then modify the network parameters.

Total Device: 3

Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6

Device Name Device Type IP Address Http Port Data Port Subnet

Product Model

About

Subnet Mask

Gateway

Restore IPC Default Configuration

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP:80

Subnet Mask: 255.255.255.0 Data Port:9008

Gateway: 192.168.226.1

Mac Address

IP Address

Modify Network Parameter

Modify

CE :98 :23 :75 :35 :22

192 .168 . 1 . 201

255 . 255 . 255 . 0

192 .168 . 1 . 1

Subnet Mask

Gateway

③MModify the IP address. The default IP address of this device is

192.168.226.201. Click the information of the camera listed in the

above table to show the network information on the right hand. Modify

the IP address and gateway of the camera and make sure the network

address is in the same local network segment as the computer. Please

modify the IP address of your camera according to the practical

situation.

For example, the IP address of your computer is 192.168.1.4. So the

IP address of the camera shall be changed to 192.168.1.X. After

modification, please enter the password of the administrator and

click “Modify” button to modify the setting.

The default password of the administrator is “123456”.

④Double-click the IP address and then the system will pop up the web

browser to connect the IP camera. Follow directions to download the plug-in

in the computer. Then enter the user name and password in the login

interface.

Table of contents

Other Nuvico Security Camera manuals

Nuvico

Nuvico Xcel NCT-8ML-E21AF User manual

Nuvico

Nuvico SD-Z35N User manual

Nuvico

Nuvico NC-2M-MPOV12 User manual

Nuvico

Nuvico MP-OV22N User manual

Nuvico

Nuvico SD-Z18 User manual

Nuvico

Nuvico ZoomMatic CI-Z22N-L User manual

Nuvico

Nuvico Xcel NCT-4M-B31AF User manual

Nuvico

Nuvico CD-ST21N User manual

Nuvico

Nuvico Easy Trak SC-S36 User manual

Nuvico

Nuvico Xcel NCT-8ML2-E21AF User manual

Nuvico

Nuvico EasyView Lite CD-H21N User manual

Nuvico

Nuvico Xcel NCT-5ML-E2 User manual

Nuvico

Nuvico Xcel NCT-8ML2-OV2 User manual

Nuvico

Nuvico NC-5M-D21 User manual

Nuvico

Nuvico SD-Z18N-PHW User manual

Nuvico

Nuvico EasyTrak SC-P36N User manual

Nuvico

Nuvico Xcel NCT-5ML-B2 User manual

Nuvico

Nuvico Xcel NTCT-3M-IRPTZ20 User manual

Nuvico

Nuvico EasyView CD-S266 User manual

Nuvico

Nuvico Zoom Matic User manual

Nuvico

Nuvico NCT-4M-MV2A User manual

Nuvico

Nuvico CB-HD21N-L User manual

Nuvico

Nuvico CF-ST1N User manual

Nuvico

Nuvico Easy View 2 CD Series User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications