Moxa Technologies EtherDevice EDS-G205A-4PoE Manual

P/N: 1802002051020

EDS-G205A-4PoE

Hardware Installation Guide

Moxa EtherDevice Switch

First Edition, October 2011

- 2 -

Overview

The EDS-G205A-4PoE series industrial Ethernet switches are rugged

entry-level industrial 5-port gigabit PoE switches that support IEEE 802.3,

IEEE 802.3u, IEEE 802.3x with 10/100/1000M, full/half-duplex,

MDI/MDIX auto-sensing, and IEEE 802.3af/IEEE 802.3at PoE standards.

The EDS-G205A-4PoE series provides 24/48 VDC redundant power inputs

that can be connected simultaneously to a live DC power source. The

switches are available with a standard operating temperature range from

0 to 60°C, or with a wide operating temperature range from -40 to 75°C,

and their IP30 metal housing makes them rugged enough for any harsh

industrial environment.

To provide greater versatility for use with applications from different

industries, the EDS-G205A-4PoE switches also allow users to enable or

disable broadcast storm protection with DIP switches on the outer panel.

The EDS-G205A-4PoE switches can be easily installed on a DIN-Rail or in

distribution boxes. The DIN-Rail mounting capability and IP30 metal

housing with LED indicators make the plug-and-play EDS-G205A-4PoE

switches reliable and easy to use.

NOTE

Throughout this Hardware Installation Guide, we use EDS as an

abbr

eviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

Package Checklist

Your EDS is shipped with the following items. If any of these items is

missing or damaged, please contact your customer service

representative for assistance.

•Moxa EtherDevice™ Switch

•Hardware Installation Guide

•Moxa Product Warranty booklet

Features

High-watt Power-over-Ethernet

•Up to 30 watts output per PoE port (IEEE 802.3at)

•Short circuit and over current protection

•Auto detection for IEEE 802.3af and IEEE 802.3at

High Performance Network Switching Technology

•10/100Base-T(X), 1000Base-T and 1000Base-X (SFP)

•10/100/1000M, Full/Half-Duplex, MDI/MDIX auto-sensing

•IEEE 802.3/802.3u/802.3x

•Store and Forward switching process type,8K MAC address entries

•9.6K jumbo frame

Rugged Design

•Redundant dual 24/48 VDC power inputs

•Operating temperature range from 0 to 60°C, or extended operating

temperature of -40 to 75°C for (T) models.

•IP30 metal housing

•DIN-rail or panel mounting ability

- 3 -

EDS-G205A-4PoE (Standard) Panel Layouts

1. Terminal blocks for

P1/P2 power inputs

2. Power input P1 LED

3. Power input P2 LED

4. PoE status LED

5. 10/100/1000Base-T(X)

PoE ports (port 2/3/4/5)

6. TP port speed LED

7. 10/100/1000Base-T(X)

port (port 1)

8. 10/100/1000Base-X SFP

slot

9. Model name

10. Grounding screw

11. P1 power input terminal

block

12. P2 power input terminal

block

13. DIP switches

14. Screw holes for panel

mounting kit

15. DIN-Rail mounting kit

- 4 -

Mounting Dimensions (unit = mm)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the EDS when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate, make sure the stiff metal spring

is situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN-Rail into

the slot just below the stiff metal

spring.

STEP 2:

The DIN-Rail attachment unit will

snap into place as shown below.

- 5 -

To remove the EDS from the DIN-Rail, simply reverse Steps 1 and 2

above.

Wall Mounting (optional)

For some applications, you will find it convenient to mount the

EDS-G205A-4PoE on the wall, as shown in the following figures.

STEP 1: Remove the

aluminum DIN-Rail

attachment plate from the

EDS-G205A-4PoE’s rear

panel, and then attach the

wall mount plates

as shown

in the diagram at the right.

STEP 2:

Mounting the EDS-G205A-

4PoE on the wall requires 4

screws. Use the switch, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be

less than 3.5 mm in diameter, as shown in the figure

at the right.

NOTE

efore tightening the screws into the wall, make sure

the screw

head and shank size

are suitable

by inserting the screw into one

of the

keyhole-shaped apertures of the wall mounting plates.

Do not screw the screws in completely

—leave about 2 mm to

allow room for sliding the wall mount panel between the wall and

the screws

STEP 3:

Once the screws are fixed on the wall, insert the four screw heads through

the large parts of the keyhole-shaped apertures, and then slide the

EDS

downwards, as indicated. Tighten the four screws for added stability.

- 6 -

Wiring Requirements

WARNING

Safety First

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure that you are using

the correct voltage. Do NOT use a voltage greater than what is

specified on the product label

Calculate the maximum possible current in each power wire and

common wire. Observe all electrica

l codes dictating the

aximum current allowable for each wire size.

If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

You should also pay attention to the following points:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

Grounding the EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be

mounted to a well-grounded

mounting surface such as a metal panel.

Wiring the Redundant Power Inputs

The two 2-contact terminal block connectors on the EDS's top panel are

used for the EDS's two DC power inputs. Top and front views of the

terminal block connectors are shown here.

- 7 -

STEP 1

: Insert the negative/positive DC wires into the V-/V+

terminals.

STEP 2

: To keep the DC wires from pulling loose, use a small

flat

-blade screwdriver to tighten the wire-clamp screws on the

front of the terminal block connector.

STEP 3: Insert the plastic terminal block connector prongs into

the terminal block receptor, which is located on

EDS’s top

panel.

ATTENTION

Before connecting the EtherDevice Switch to the DC power

inputs, make sure the DC power source voltage is stable.

Communication Connections

The EDS-P205A-4PoE switches have 4 10/100/1000Base-T(X) PoE

Ethernet ports for connecting PoE devices, and 1 10/100/1000Base-T

port or 1 1000Base-X SFP slot for uplink connection.

10/100/1000Base-T(X) Ethernet Port Connection

10/100/1000Base-T(X) ports located on the EDS’s front panel are used to

connect to Ethernet-enabled devices. Below we show pinouts for both

MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and also show

cable wiring diagrams for straight-through and cross-over Ethernet

cables.

10/100Base-T(X) Pinouts

MDI Port

Pinouts

MDI-X Port

Pinouts

8-pin RJ45

Pin Signal Pin Signal

TX+

RX+

2 TX- 2 RX-

3 RX+ 3 TX+

4 RX- 4 TX-

- 8 -

1000Base-T Pinouts

MDI Port

Pinouts

MDI-X Port

Pinouts

8-pin RJ45

Signal

BI_DA+

BI_DB+

BI_DA-

BI_DB-

BI_DB+

BI_DA+

BI_DC+

BI_DD+

BI_DC-

BI_DD-

BI_DB-

BI_DA-

BI_DD+

BI_DC+

BI_DD-

BI_DC-

PoE Ethernet Port Connection

PoE ports located on the EDS switch’s front panel are used to connect to

PoE-enabled devices. The pinout follows the Alternative A, MDI mode” of

802.3af/802.3at standards. Please see the details in the following table.

PoE Port Pinout

Power

8-pin RJ45

1 V+

2 V+

3 V-

6 V-

NOTE

According to IEEE 802.3af/at standards, the PD shall be

implemented to be insensitive to the polarity of the power supply

and shall be able to operate per MDI mode and MDI

-X mode.

However, some PDs only support MDI mode or MDI

-X mode only.

The following figure shows how to select the correct cable

between the PD and EDS-G205A-4POE.

- 9 -

RJ45 (8-pin) to RJ45 (8-pin) Cable Wiring

NOTE

If the PD only supports PoE MDI mode (V+, V+, V-, V- for pins 1,

2, 3, 6), choose a cross

-over Ethernet cable to connect the PD

and the EDS switch. If the PD only supports

PoE MDI-X mode (V-

-, V+, V+ for pins 1, 2, 3, 6), choose a straight-through

Ethernet cable between the PD and the EDS switch.

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power

sources. If one power source fails, the other live source acts as a backup,

and automatically supplies all of the EDS’s power needs.

DIP Switch Settings

The default setting for each DIP Switch is

OFF. The following table explains the effect

of setting the DIP Switches to the ON

positions.

- 10 -

DIP Switch Setting Description

– – Serves no function (reserved for future use).

BSP ON Enables broadcast storm protection

OFF Disables broadcast storm protection

ATTENTION

To actively update DIP switch settings, power off and then power

on the EDS.

LED Indicators

The front panel of the EDS switches contain several LED indicators. The

function of each LED is described in the following table.

LED Color State Description

P1 AMBER On

Power is being supplied to power input

P1.

Off

Power is not being supplied to power

input P1.

P2 AMBER On

Power is being supplied to power input

P2.

Off

Power is not being supplied to power

input P2.

10/100/1000

AMBER On TP port’s 10/100 Mbps link is active.

Blinking

Data is being transmitted at 10/100

Mbps.

Off

TP Port’s 10/100 Mbps link is inactive.

GREEN

TP port’s 1000 Mbps link is active.

Blinking

Data is being transmitted at 1000

Mbps.

Off

TP Port’s 1000 Mbps link is inactive.

1000 GREEN On SFP module’s 1000Mbps link is active.

Blinking

Data is being transmitted at 1000

Mbps.

Off SFP module’s 1000Mbps link is

inactive.

PoE+

AMBER

The PoE device is connected by IEEE

802.3af standard

Off No PoE power output or no PoE

connected PoE devices

Green

The PoE device is connected by IEEE

802.3at standard

Off No PoE power output or no PoE

connected PoE devices

Red

Blinking

PoE failure:

- 1 time/s: PoE standard detection

1x…………...failure

- 2 times/s: PoE current overload

Off No PoE failure

Other manuals for EtherDevice EDS-G205A-4PoE

Table of contents

Other Moxa Technologies Network Router manuals

Moxa Technologies

Moxa Technologies TSN-G5000 Series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T User manual

Moxa Technologies

Moxa Technologies OnCell 5004 Series User manual

Moxa Technologies

Moxa Technologies EDS-505A Series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manual

Moxa Technologies

Moxa Technologies Managed Ethernet Switch/Extender User manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 User manual

Moxa Technologies

Moxa Technologies ioLogik E2200Series User manual

Moxa Technologies

Moxa Technologies EDR-G9010 Series User manual

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Manual

Moxa Technologies

Moxa Technologies UC-8112-LX-STK User manual

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Manual

Moxa Technologies

Moxa Technologies IKS-6324 Series Manual

Moxa Technologies

Moxa Technologies EDS-210A-1GTX-1GSFP-4SFP User manual

Moxa Technologies

Moxa Technologies TN-4900 Series User manual

Moxa Technologies

Moxa Technologies EDR-810 Series Manual

Moxa Technologies

Moxa Technologies EDS-G308 Manual

Moxa Technologies

Moxa Technologies ioLogik E1200 Series User manual

Moxa Technologies

Moxa Technologies WDR-3124A User manual

Moxa Technologies

Moxa Technologies NSwitch User manual

Moxa Technologies

Moxa Technologies AWK-4121 User manual

Moxa Technologies

Moxa Technologies SDS-3008 Series User manual

Moxa Technologies

Moxa Technologies ioLogik E1242 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview