Moxa Technologies TSN-G5000 Series User manual
P/N: 1802050080011
*1802050080011*
TSN-G5000 Series
Quick Installation Guide
Moxa Industrial Managed Ethernet Switch
Version 1.0, June 2020
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
Moxa India:
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
2020 Moxa Inc. All rights reserved.
- 2 -
Package Checklist
The TSN-G5000 Series is shipped with the following items. If any of
these items are missing or damaged, please contact your customer
service representative for assistance.
•1 TSN-G5000 Series industrial Ethernet switch
•1 RJ45 to RS-232 9-pin female console cable
•1 Quick installation guide (printed)
•1 Warranty card
•2 Terminal blocks
Default Settings
•Default IP address: 192.168.127.253
•Default Subnet Mask: 255.255.255.0
•Default User Name: admin
•Default Password: moxa
TSN-G5000 Series Panel Layout
TSN-G5004
- 3 -
TSN-G5008-2GTXSFP
1. USB storage port (type A, currently disabled)
2. Console port (RJ45, RS-232)
3. LED indicators x 5 (STATE, FAULT, PWR1, PWR2, SYNC)
4. Ethernet ports x 4 (8 for TSN-G5008), (RJ45,
10/100/1000BaseT(X))
5. LED indicator for 1000BaseT(X)
6. LED indicator for 10/100BaseT(X)
7. Ethernet ports x 2 (SFP, 100/1000BaseSFP)
8. Rubber cover for reset button and microSD card slot (currently
disabled)
9. Grounding screw (chassis ground)
10. Relay output (terminal block)
11. Power inputs x 2 (terminal block)
12. Digital input (terminal block)
13. DIN-rail mounting kit
14. Screw holes reserved for DIN-rail kit side mounting
15. Model side label (multiple product information included)
- 4 -
Dimensions
TSN-G5004
TSN-G5008-2GTXSFP
Unit: mm (inch)
- 5 -
DIN-Rail Mounting
There are two options for DIN-rail mounting that can be used for the
TSN-G5000 Series. Option 1 is the default type when shipped.
Option 1 (default):
When shipped, the metal DIN-rail mounting kit is fixed to the back
panel of the TSN-G5000 Series. Mount the TSN-G5000 Series on the
corrosion-free mounting rail that adheres to the EN 60715 standard.
Suggested Installation Method
Step 1—Insert the upper lip
of the DIN
-rail kit into the
mounting rail.
Step
2—Press the TSN-
G5000 Series towards the
mounting rail until it snaps
into place.
Suggested Removal Method
Step 1—Pull down the latch
on the DIN
-rail kit with a
screwdriver.
Steps
2 & 3—Slightly pull
the TSN
-G5000 Series
forward and lift up to remove
it from the mounting rail.
- 6 -
Option 2 (when side cabling is needed):
The metal DIN-rail mounting kit can be fixed to the side panel of the
TSN-G5000 Series. Mount the TSN-G5000 Series on the corrosion-free
mounting rail that adheres to the EN 60715 standard.
Default Installation
Side Installation
Suggested Installation Method
Step 1—Detach the metal DIN-rail mounting kit from the back panel
and attach it to the side panel, vertically as indicated in the figure
below.
Step 2—Insert the upper lip of the
DIN
-rail kit into the mounting rail.
Step
3—Press the TSN-G5000
Series towards the mounting rail
until it
snaps into place.
- 7 -
Suggested Removal Method
Step 1—Pull down the latch on the
DIN
-rail kit with a screwdriver.
Steps
2 & 3—Slightly pull the TSN
-
G5000 Series forward and lift up to
remove it from the mounting rail.
NOTE
Screws that are used to fix the DIN-rail kit on the TSN-G5000
Series should be securely fastened before mounting on the
mounting rail. Please make sure that if you remove the DIN
-rail
kit, it must be securely fastened when it is reattached.
Wall-mounting
For some applications, you will find it convenient to mount your TSN-
G5000 Series on the wall, as illustrated below.
Step 1—Remove the aluminum DIN-rail attachment plate from the
TSN-G5000 Series rear panel, and then attach the wall mount plates,
as shown in the diagram below.
- 8 -
Step 2—Mounting the TSN-G5000 Series on the
wall requires
four screws. Use the switch, with
wall mount plates attached, as a guide to mark
the correct locations of the
four screws. The
heads of th
e screws should be less than 6 mm in
diameter, and the shafts should be less than 3.5
mm in diameter, as shown in the figure at the
right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw into
one of the keyhole
-shaped apertures of the wall mounting
plates.
Do not screw the screws in all the way—leave about 2 mm to allow
room for sliding the wall mount panel between the wall and the screws.
Step 3—Once the screws are fixed in the
wall, insert the four screw heads through
the large parts of the keyhole
-shaped
apertures, and then slide
the TSN-G5000
Series
downwards, as indicated on the
right
. Tighten the four screws for added
stability.
ATTENTION
Safety First!
External metal parts are hot. Take necessary precautions if it is
necessary to touch.
ATTENTION
In order to ensure
reliable operations, please make sure the
operating temp
erature
of the environment does not exceed the
spec
ifications. When mounting a TSN-G5000 Series with other
operating units in a cabinet without forced ventilation,
a
minimum
of 5 cm space on both the left and right of
the switch
is recommended.
- 9 -
Wiring Requirements
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Mox
a TSN-G5000 Series. Calculate the maximum
possible current in each power wire and common wire. Observe
all electrical codes dictating the maximum current allowable for
each wire size. If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to your
equipment.
Be sure to read and follow these important guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE
Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires
with different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb
is that wiring that shares similar electrical characteristics can be
bundled together.
•You should separate input wiring from output wiring.
•We advise that you label the wiring to all devices in the system.
Grounding the TSN-G5000 Series
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw (chassis ground) to the grounding surface prior to
connecting devices. The grounding screw is located on the top panel of
the TSN-G5000 Series.
ATTENTION
This product is intended to be mounted onto a well
-grounded
mounting surface, such as a metal panel.
- 10 -
Suggested Wire Type for Wiring Relay Contact
(R), Digital Input (DI) and Power Inputs (P1/P2)
The switch includes two 4-pins, 3.5 mm pin-pitch terminal blocks. The
following includes suggestions for wiring the relay contact (R), digital
input (DI) and power inputs (P1/P2) for the TSN-G5000 Series.
ATTENTION
We suggest using
a copper conductor with the cable type -
AWG (American Wire Gauge) 18
-24 and the corresponding pin
type cable terminals. In addition, the wire must be able to
withstand at least 105°C.
NOTE
We suggest the length of the pin type cable terminal is 8 mm.
In order t
o tighten the wire properly, please perform the
following three steps:
Step 1. Use a small flathead screwdriver
to press the push
-
in button beside each terminal of the terminal
block conn
ector. Step 2. Insert the wire. Step 3. Release the
screwdriver after the wire has been fully inserted. Please refer
to the diagram below.
Wiring the Relay Contact
The TSN-G5000 Series has one relay output for identifying when a
specific event has occurred (i.e., fault; see below). This relay output
uses the first contact out of the first 2-pin terminal on the TSN-G5000
Series' top panel.
Refer to the instructions and diagram below on how to connect the
wires to the terminal block connector, and how to attach the terminal
block connector to the terminal block receptor.
Step 1—Insert two wires into the relay position (see the diagram below
showing the top view) on the terminal to form an open circuit.
Step 2—To keep the relay wires from coming loose, use a small
flathead screwdriver to press the button beside each terminal of the
plastic terminal block connector in order to insert the wire tightly.
Release the screwdriver after the wire has been inserted properly.
This manual suits for next models
4
Table of contents
Other Moxa Technologies Network Router manuals
Moxa Technologies
Moxa Technologies TN-4900 Series User manual
Moxa Technologies
Moxa Technologies ioLogik E1200 Series User manual
Moxa Technologies
Moxa Technologies ETHERDEVICE EDS-308 Manual
Moxa Technologies
Moxa Technologies NAT-102 Series User manual
Moxa Technologies
Moxa Technologies ioLogik E1210 User manual
Moxa Technologies
Moxa Technologies EDR-8010 Series User manual
Moxa Technologies
Moxa Technologies MAR-2000 User manual
Moxa Technologies
Moxa Technologies EtherDevice Switch EDS-G205 Manual
Moxa Technologies
Moxa Technologies EDS-405 User manual
Moxa Technologies
Moxa Technologies OnCell 5004 Series User manual
Moxa Technologies
Moxa Technologies EDS-G308 Manual
Moxa Technologies
Moxa Technologies SDS-3008 Series User manual
Moxa Technologies
Moxa Technologies EDS-518E User manual
Moxa Technologies
Moxa Technologies EtherDevice EDR-G902 Manual
Moxa Technologies
Moxa Technologies EDR-810 Series Manual
Moxa Technologies
Moxa Technologies ioLogik E2200Series User manual
Moxa Technologies
Moxa Technologies NPort IA5150 series User manual
Moxa Technologies
Moxa Technologies ioLogik E1200 Series User manual
Moxa Technologies
Moxa Technologies UC-8112-LX-STK User manual
Moxa Technologies
Moxa Technologies ToughNet TN-5308-4 Manual
