Mitsubishi MELSEC-F FX-10DM-E User manual

USER’S MANUAL

FX-10DM-E DISPLAY MODULE

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the correct installation

and operation of the DISPLAY MODULE FX-10DM-E. It should be read and understood before attempting to

install or use the unit.

• If in doubt at any stage of the installation of DISPLAY MODULE FX-10DM-E always consult a professional

electrical engineer who is qualified and trained to the local and national standards which apply to the

installation site.

• If in doubt about the operation or use of DISPLAY MODULE FX-10DM-E please consult the nearest

Mitsubishi Electric distributor.

• This manual is subject to change without notice.

Notification of CE marking

The following products have shown compliance through direct testing (to the identified stan-

dards) and design analysis (forming a technical construction file) to the European Directive for

Electromagnetic Compatibility (89/336/EEC) when used as directed by the appropriate docu-

mentation.

Type : Programmable Controller (Open Type Equipment)

Models : MELSEC DM series products, identified here, manufactured from

January 1st, 2002 FX-10DM-E

(For this product see note under and over the page)

For more details please contact the local Mitsubishi Electric sales site.

Standard Remark

EN50081-2 :1993

Electromagnetic compatibility

- Generic emission standard Industrial

environment

Compliance with all relevant aspects of the standard.

(Radiated Emissions and Mains Terminal Voltage

Emissions)

EN61131-2 :1994 + A11: 1996 + A12: 2000

Programmable controllers

-Equipment requirement and tests

Compliance with all relevant aspects of the standard.

(RF Immunity, Burst Transients and ESD)

FX-10DM-E DISPLAY MODULE

Notes Regarding the use of DM Units

General notes on the use of Communication Cables

Any device which utilizes a data communication function is susceptible to the wider effects of

local EMC noise. Therefore, when installing any communication cables care should always be

taken with the routing and location of those cables. The DM units identified on the previous page

are compliant with the EMC requirement when the following communication cables are used :

When using the FX-20P-CAB0/EN cable the Earth Strap must be connected to a suitable earth

point.

Ex. 1

Table 0.1:

DM Unit New Cables Existing Cables User Made Cables

FX-10DM-E

From version A

(JY309C24571A) of

the FX-20P-CAB0/EN

FX-20P-CAB0 modified

as shown in EX.1

This cable need to be independently

tested by the user to demonstrate EMC

compatibility when they are used with

Mitsubishi DM units and Programma-

ble Controllers.

40mm

FX-20P-CAB0

Programmable

Controller DM units

E = Additional earth strap connected to the cables

shield. Free end of the earth strap must be

connected to an earth point.

F = Ferrite core

Ex. Tokin - ESD-R-14S or similar

FX-10DM-E DISPLAY MODULE

USER’S MANUAL

FX-10DM-E DISPLAY MODULE

Manual number : JY992D86401

Manual revision : C

Date : March 2003

FX-10DM-E DISPLAY MODULE

Guidelines for the Safety of the User and Protection of the DISPLAY MODULE

FX-10DM-E.

This manual provides information for the use of the DISPLAY MODULE FX-10DM-E. The

manual has been written to be used by trained and competent personnel. The definition of

such a person or persons is as follows:

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual, should be of a competent

nature, trained and qualified to the local and national standards required to fulfill that

role. These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for said product. All

maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (see Note) should be trained to use this

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is associated with the actual operation

of the completed equipment.

Note : The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

FX-10DM-E DISPLAY MODULE

Notes on the Symbols Used in this Manual

At various times throughout this manual certain symbols will be used to highlight points which

are intended to ensure the users personal safety and protect the integrity of equipment.

Whenever any of the following symbols are encountered its associated note must be read and

understood. Each of the symbols used will now be listed with a brief description of its meaning.

Hardware Warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software Warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should

be aware.

6) Indicates a point of interest or further explanation.

FX-10DM-E DISPLAY MODULE

vii

• Under no circumstances will Mitsubishi Electric be liable responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

• Please contact a Mitsubishi Electric distributor for more information concerning applications

in life critical situations or high reliability.

FX-10DM-E DISPLAY MODULE

viii

Table of contents

Other Mitsubishi Controllers manuals

Mitsubishi

Mitsubishi Melsec A series Manual

Mitsubishi

Mitsubishi FX3U-485ADP User manual

Mitsubishi

Mitsubishi Q64TD User manual

Mitsubishi

Mitsubishi Q172CPU User manual

Mitsubishi

Mitsubishi MELSEC QJ71C24-R2 User manual

Mitsubishi

Mitsubishi FX1N-485-BD User manual

Mitsubishi

Mitsubishi A1SJ61BT11 User manual

Mitsubishi

Mitsubishi Q170MCPU User manual

Mitsubishi

Mitsubishi MELSEC Q Series User manual

Mitsubishi

Mitsubishi MELSEC System Q Owner's manual

Mitsubishi

Mitsubishi MELSEC-A series User manual

Mitsubishi

Mitsubishi MELSEC iQ-R series User manual

Mitsubishi

Mitsubishi MELDAS TRS50 User manual

Mitsubishi

Mitsubishi MELSEC-L Series Owner's manual

Mitsubishi

Mitsubishi AL-232CAB User manual

Mitsubishi

Mitsubishi FX3U-32DP User manual

Mitsubishi

Mitsubishi JY992D74401C User manual

Mitsubishi

Mitsubishi q64rd User manual

Mitsubishi

Mitsubishi MELSEC-Q/L Owner's manual

Mitsubishi

Mitsubishi A2USCPU(S1) User manual

Mitsubishi

Mitsubishi MELSEC Q Series Owner's manual

Mitsubishi

Mitsubishi Q64AD User manual

Mitsubishi

Mitsubishi 00JCPU User manual

Mitsubishi

Mitsubishi MELSEC-A A1SCPUC24-R2 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual