Mintronix Computer Solutions MP5000C User manual
M I N T R O N I X C O M P U T E R S O L U T I O N S
User’s Guide
M P 5 0 0 0 C 12” A L L - IN- O N E T O U C H
S C R E E N C O M P U T E R S Y S T E M
This manual is intended to provide both general information on small point of sales
technology and technical specifications of the MP5000C computer. The information
provided herein is of a proprietary nature to the original manufacturer and may not
be distributed without express written consent from an officer of the company. This
manual has been supplied in confidence and is intended for use by authorized
recipients only. This manual may not be copied or reproduced in whole or in part, nor
may its contents be revealed in any manner to any person other than the authorized
personnel.
This document has been prepared with the utmost effort to insure the information
contained within is accurate and complete. However, the original manufacturer
reserves the right to make product improvements or changes at any time without
advanced notice. Furthermore, the original manufacturer assumes no liability arising
from use of the products described herein. Working with the MP5000C
computer involves hazardous levels of voltages and can present serious shock hazard.
Work should only be performed by appropriately qualified technical personnel.
The original manufacturer’s products are not authorized or designed for use in critical
lifesaving equipment. The original manufacturer’s products are warranted for one
year from the date of purchase against component and workmanship defects. The
original manufacturer’s Return Merchandise Authorization (RMA) policy requires the
user to obtain an RMA # prior to sending back any item to be repaired or replaced.
Replacement or repair will be free of charge for all items under warranty only when
the merchandise is returned to the original manufacturer, not a third-party repair
depot. Returned goods need to have pre-paid freight along with a copy of the original
invoice; collect freight items will not be accepted and will be returned to sender. For
specific return circumstances and/or warranty information, please contact your
dealer.
All trademarks mentioned herein belong to their respective companies.
Copyright: 2018
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Version 1-2018
Page 3
Table of Contents
1.0
Introduction
5
2.0
Standard Features
5
3.0
Input/Output
6
4.0
Graphics
6
5.0
Touch Screen
7
6.0
Power Supply
7
7.0
Environment
7
8.0
Physical Dimensions
7
9.0
Optional Accessories
7
10.0
Setup Installation
8
10.1
Unpacking
8
10.2
Site Selection
8
10.3
Installation Checklist
8-9
11.0
Bios Introduction
9
11.1
Bios Setup
9
11.2
Bios Main Menu
10
11.3
Bios Operation
11
11.4
Advanced Bios Features
11
12.0
ACPI Settings
11
13.0
Super I/O Configuration
12
14.0
Embedded Controller Configuration
12
15.0
S5 RTC Wake Settings
12
16.0
Serial Port Console Redirection
12
17.0
CPU Configuration
12-13
18.0
PPM Configuration
13
19.0
IDE Configuration
13
20.0
CSM Configuration
13
21.0
USB Configuration
14
22.0
Security Configuration
14
23.0
Chipset Configuration-North Bridge
14
23.1
Intel IGD Settings
15
23.2
LCD Control
15
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Version 1-2018
Page 4
23.3
TOLUD Value
15
24.0
Chipset Configuration-South Bridge
15-16
24.1
Azalia HD Audio
16
24.2
USB Configuration
16
24.3
PCI Express Configuration
16
25.0
Security
16
26.0
Boot
17
27.0
Save & Exit Configuration
17
28.0
Jumper Settings
18
29.0
Installing Software & Drivers
18
29.1
Operating Systems
18
29.2
Touch Screen Driver
18
29.3
Tuning Touch Screen
18
29.4
Other Applications
18
30.0
Troubleshooting
19
30.1
Initial Inspection
19
30.2
Peripherals Configuration
19
30.3
Connection Problems
20
31.0
Standard IRQ Settings
20
32.0
Optional MSR
20
32.1
Reader Test
21
32.2
Changing Configuration
21
32.3
Power-Up Initialization
21
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Version 1-2018
Page 5
1.0 Introduction
The All-in-One touch screen computer with adjustable viewing angle has the flexibility
of a PC-based computer and architecture combined with advanced LCD and touch
screen technology to form a low cost, small-sized computer that runs all PC-based
software. Its unique design allows for ease of use with any applications. With
networking capability, this computer is ideal for information kiosk, point of
sales, and practically anything one can imagine.
2.0 Standard Features
Processor
Celeron® N2930 1.83GHz (burst frequency 2.16GHz), quad
cores, four threads
Bios
AMI UEFI 64 Mbit, BIOS for 64 or 32bit is different, default
version is for 64bit. Default setting is Legacy boot, that can be
manually changed to UEFI boot. If default setting to UEFI is
needed, that can be done by T-P/N.
Memory
Non-ECC, DDR3L 2G or 4G on-board memory. 64-bit data
busDDR3L with 1333 MT/s data rates for N2930, total
memory bandwidth can be scalable to 21.3GB/s. Aggressive
power management to reduce power consumption.
Chipset
Intel® Celeron® N2930
Storage Devices
SATA up to 3GB (300MB); mSATA 1 x full size
Watchdog Timer
Can generate a system reset. The watchdog timer is
programmable, with each unit equal to one second or one
minute (255 levels).
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Version 1-2018
Page 6
3.0 Input/Output
Serial
RS-232/422/485 for COM1, 3 RS-232 for COM2/3/4
Ethernet
Controller: Realtek RTL8111E-VL-CG
•2 - 10/100/1000 BASE-T
•Fully compliant with IEEE802.3, IEEE802.3u,
IEEE802.3ab
•9 KB Jumbo frames supported (Full-duplex)
•Full duplex flow control supported
Keyboard/Mouse
One connector is located on the mounting bracket for
easy connection to PS/2 keyboard and mouse.
USB
1 - 3.0 USB, 1 USB 2.0 on rear I/O and 4 internal USB 2.0.
PCI Bus
Mini PCIe / mSATA
•1 Full-size Mini PCIe (with PCIe and USB interface)
•1 Full-size mSATA (with SATA and USB interface)
General Purpose
8-bit Programmable General Purpose Input/ Output from
iManager
4.0 Graphics
Display Controller
Intel® 7th generation (Gen 7)
Display
Multi-display interfaces: VGA, HDMI/DisplayPort, 48-bit LVDS.
•Supports Extend/ Clone Mode with multi-display device
•Dual display: any two combination between VGA,
HDMI, LVDS
VGA: 2560 x 1600 at 60Hz
HDMI/DisplayPort: HDMI 1.4a with audio, up to 1080P at
60Hz.
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Version 1-2018
Page 7
5.0 Touch Screen
Touch Screen
5 wire resistive technology integrated USB controller,
using mouse emulation
6.0 Power Supply
Power Supply
Voltage
Single +12V DC ± 10% power input
7.0 Environment
Operating
Temperature
0 ~ 60° C (32 ~ 140° F)
Storage
Temperature
-40~85°C
8.0 Physical Dimensions
Weight
.05 kg
Board Size
146 x 102 mm (5.7 x 4 inches)
9.0 Optional Accessories
Magnetic Stripe
Reader
1~3 track HID USB reader
Barcode Scanner
CCD miniature scanner
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Page 8
Version 1-2018
10.0 Set Up and Installation of the All-in-One
10.1 Unpacking. What you should have:
✓MP5000C computer monitor base unit
✓Screws to attach the base unit to the computer monitor
✓Power adapter and power cord
✓Drivers and manual files (included on the hard drive)
10.2 Site Selection:
Consider the following when selecting sites:
✓The area should be well ventilated
✓Avoid glare from bright overhead lighting
✓The system should be placed on a hard surface
✓There should be easy access for power and other cabling requirements
10.3 Installation Checklist:
Route cables through the cast alloy stand and position the cables to the
side of the stand
Insert stand front tabs into slots on back of MP5000C
Remove the screw on the center top of the MP5000C and use it to secure
the stand to the computer
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Page 9
Version 1-2018
Route all other peripheral cables through the stand
Connect them to the MP5000C computer. Set the computer in upright
position.
Connect all the peripherals to the cables
Turn the computer on
Install operating system software (pre-installed if purchased with system)
Install software driver’s
Install application software
11.0 BIOS Introduction
The MP5000C can modify BIOS settings to control the special features of your
computer. The Setup program uses several menus for making changes.
11.1 BIOS Setup
The MP5000C computer has the AMI BIOS built in, with a CMOS SETUP utility that
allows users to configure required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS RAM of the motherboard.
When the power is turned off, the battery on the board supplies the necessary power
to preserve the CMOS RAM.
When the power is turned on, press the <Del> button during the BIOS POST (Power-
On Self-Test) to access the CMOS SETUP screen.
M I N T R O N I X C O M P U T E R S O L U T I O N S
124 Old Mill Road, Suite H
Greenville, SC 29607
855-672-6464
Page 10
Version 1-2018
11.2 BIOS Main Menu
Press <Del> to enter AMI BIOS CMOS Setup Utility, the Main Menu will appear on
the screen. Use arrow keys to select among the items and press <Enter> to accept or
enter the sub-menu.
Control Keys
< ↑ >< ↓ >< ← >< → > Move to select item
<Enter> Select Item
<Esc> Main Menu - Quit and not save changes into CMOS
Sub Menu - Exit current page and return to Main Menu
<Page Up/+> Increase the numeric value or make changes
<Page Down/-> Decrease the numeric value or make changes
<F1> General help, for Setup Sub Menu
<F2> Item Help
<F5> Load Previous Values
<F7> Load Setup Defaults
<F10> Save all CMOS changes
Table of contents
