Minerva 5565 User manual
Valve
Use the 5 screws for the
holes shown here.
Screw the camber nut over the bolt,
then the bolt into the bracket .
36"
Use the 5 included screws as shown to affix the bracket to the wall.
Screws should be anchored into studs where available, or anchors
for the appropriate material otherwise (not provided).
Align the bracket against the wall such that the top of the bracket
is approximately 3' (36") off the floor.
1 - Bracket Installation
A LICENSED PLUMBER MUST PERFORM ALL INSTALLATION
FOR PLUMBING AND ALL PLUMBING-RELATED EQUIPMENT.
FAILURE TO DO SO WILL VOID THE WARRANTY.
AT NO TIME SHOULD ANY PRODUCT CONTAINING BLEACH OR
BARBICIDE BE USED TO CLEAN OR SANITIZE ANY OF THE
SHAMPOO SINKS. SUCH PRODUCTS MAY CAUSE THE
BREAKDOWN OF SEALS AND RESULT IN LEAKING.
DOCUMENTATION OF INSTALLATION BY A LICENCSED PLUMBER
MUST BE PROVIDED TO MINERVA BEAUTY, INC.
FOR ALL PLUMBING RELATED WARRANTY ISSUES.
WWW.MINERVABEAUTY.COM/MAINTENANCE.HTM
!! Safety and Warranty Information !!
Brass Slipnut
Tail Washer
Tail Pipe
Brass Locknut
Drain Cover
Rubber Washer
Drain
Strainer Basket 1x
1x
2x
1x
1x
1x
1x
1x
Cumberland Bowl
Callaway Bowl
- OR -
Faucet Washer
Mounting Bracket
Bracket Screws
Camber Bolt
Camber Nut
1x
1x
- OR -
1x
1x
1x
5x
1x
1x
Parts List
Cumberland Shampoo Bowl
Model 5560
Callaway Shampoo Bowl
Model 5565
For Minerva Beauty Callaway and
Cumberland Shampoo Bowls.
Assembly Instructions
5 - Valve and Hose Installation
4. Attach hose to valve
1. Unscrew nut to lower
3. Tighten nut to
secure valve
2. Slide washer
over pipes
1. Drop the valve through the right-hand hole in the bowl.
2. Unscrew the nut on the threaded pipe to make room for the washer.
3. Slip the washer over the pipes, then tighten the bolt back up to secure the valve.
4. Drop the hose through the left-hand hole in the bowl, and screw the end of the
hose onto the threaded pipe on the valve.
Tighten
~1/8"
2. Adjust the camber bolt in the
bracket such that there is
about 1/8" between the bowl
and the bolt.
1. Hang the bowl over the bracket, aligning
the notches in the bracket with the hooks
in the back of the bowl (A + B).
B
B
AA
4 - Mounting the Bowl
1. Insert the small end of the tail washer into
the end of the tail pipe with the lip.
2. Slide the slipnut over the tail pipe and
screw it onto the threads on the drain.
Slipnut
Tail Pipe
Tail Washer
3 - Tail Pipe Installation
1. Set strainer basket inside drain.
2. Set drain into sink, using plumber's
putty to create a watertight seal.
3. Place rubber washer on the upper lip
of the drain cover (only 1 required).
4. Slip drain cover over drain threads.
5. Screw the locknut onto the drain threads,
larger end up, and tighten it all the way so it
presses the drain cover and washer against
the bowl and prevents the drain from moving.
Locknut
Drain Cover
Washer
Bowl
Drain
Strainer
2 - Drain Installation
3. Holding the bolt steady, tighten
the nut against the bracket
using the included wrench.
This manual suits for next models
1
Other Minerva Plumbing Product manuals
Popular Plumbing Product manuals by other brands
Weka
Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS
Kohler
Kohler K-6228 Installation and care guide
UBERHAUS DESIGN
UBERHAUS DESIGN 75175017 Operator's manual
American Standard
American Standard DetectLink 6072121 manual
Uponor
Uponor Contec TS Mounting instructions
Pfister
Pfister Selia 49-SL Quick installation guide
Kohler
Kohler Centerset K-15240 Homeowner's guide
Viega
Viega Prevista Dry 8522.33 Instructions for use
Sanela
Sanela Lema SLP 59RB Instructions for use
Elkay
Elkay EDF15AC Installation, care & use manual
Hans Grohe
Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions
baliv
baliv WT-140 manual