Miele PT 8807 EL User manual

38.15

en - US

Mat. NR. 09 883 210 / 02

Installation plan

Tumble dryer

PT 8807 EL (Electrically heated)

Mat. NR. 09 883 210 / 02

It is essential to read the operating and installation instructions before

installing, commissioning or using the machine.

This avoids the risk of accidents or damage.

U.S.A.

Miele, Inc.

National Headquarters

9 Independence Way

Princeton, NJ 08540

Phone:

Fax:

www.mieleusa.com

Technical Service & Support

Nationwide

Phone: 800-991-9380

Fax: 800-220-1348

[email protected]

800-991-9380

609-419-4241

Installation plan: PT 8807 EL

Date: 2015-Sep-15 Page: 8

Technical datasheet

Tumble dryer:

Heating:

PT 8807

Electric (EL)

Legend:

Abbreviations in bold type:

Connection required

en - US

Abbreviations in circle with dashes:

Connection optional or required depending on model version

Optional extras:

Concrete base

Quality and density of concrete must comply with load.

Concrete plinth must be firmly secured to floor!

Recommended height

100

4“

Minimum height

2“

Minimum width

1.200

47“

Minimum depth

1.400

55“

Machine connections:

Electrical

connection

Voltage

3 AC 208

Frequency

Rated load

27.4

Fuse rating

3 × 90

Connection cable, min. cross-section

mm²

AWG 16

Cable screw connector

M 50

Connection cable to be ordered separately.

Electrical connection must comply with national

regulations

If machines are hard-wired, a multi-pole main switch must

be provided on site.

A wall socket or main isolator must be accessible after

installation.

Equipotential

bonding

Connection with male thread

10 × 35

with washers and nut

Accessories not included.

If necessary, equipotential bonding with good galvanic

contact must be provided in accordance with all

appropriate national and local regulations.

Peak load

energy

management

Control contact voltage

AC 230

Connection cable, min. cross-section

mm²

5 × 1,5

Connection cable to be ordered separately.

Connection via a flexible supply lead with a separate

isolator is recommended. The isolator should be visible

and easily accessible after machine installation.

Vented

m³/h

1.100

38,85 cu ft/h

Max. Nominal air flow in vented mode

Max. Permissible pressure loss

Connection on machine side (ext. diameter)

150

6“

Connection pipe provided on site (int. diameter)

150

6“

Max. temperature

°C

176 °F

As relative humidity inside the vent ducting can be as high

as 100%, suitable measures must be taken to prevent a

backflow of condensate into the machine.

Pa 300 0.04 PSI

Installation plan: PT 8807 EL

Date: 2015-Sep-15 Page: 9

Air intake Standard connection: Air intake from installation site

Unobstructed air intake into room recommended

(corresponding to 3 times the vent cross-section of

machine)

cm²

531

32 cu in

A sufficient supply of fresh air should be ensured to

replace the air extracted.

Alternative connection: Ducted air intake (from outside

building)

Connector on machine (int. diameter)

161

6 ½“

Connection pipe provided on site (ext. diameter)

160

6 ¼“

Lid removal exposes live components! For safety

reasons, the pipe connected for central air intake should

be at least 900 mm long and secured using two screws.

Fittings

(supplied)

6 × 40

10 × 50

Without base

2 × clamps

2 × screws DIN 571 (Ø × length)

2 × rawl plugs (Ø × length)

The machine should be bolted to the floor.

Fixing materials for a floating screed floor are to be

provided on site.

6 × 40

10 × 50

On concrete platform

2 × clamps

2 × screws DIN 571 (Ø × length)

2 × rawl plugs (Ø × length)

The machine must be bolted to the floor!

Fixing materials for a floating screed floor are to be

provided on site.

Machine data

Unit width

1.206

47 ½“

Machine depth

1.384

54 ½“

Unit height

1.640

64 ½“

Casing width

1.200

47 ¼“

Casing depth

1.279

50 ½“

Minimum width of delivery access to installation site

1.220

48“

Recommended rear wall gap (measured to front of

machine)

1.800

71“

Min. wall gap (to rear edge of lid)

500

19 ¾“

287632 lb

3.708

Watt

973

dB (A)

73,6

Net weight

Max. load bearing in operation

Average heat dissipation

(dependent on ambient room temperature and program

selected)

A Noise level

A Sound pressure level

dB (A)

Installation should only be carried out by authorised installers in accordance with all local and national regulations!

Table of contents

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions

Frigidaire

Frigidaire CAQE7077KW0 use & care