Maytag MDG18CSAW User manual

ISTALLATI

COMMERCIAL

ICTI

DRYERGAS OR ELECTRIC

MODELS M DG 18CSAW/M NAW/PDAW/PDAX/PRAW

M D E18 M NAY/M NAZ/CSAY/CSAZ/PDAY/PDAZ/PRAY/PRAZ

IUCTI S I

SECHEUSE A USAGE COMMERCIAL ,_ GAZ OU ELECTRIQUE

M ODELES MDG 18CSAW/M NAW/PDAW/PDAX/PRAW

MDE18M NAY/M NAZ/CSAY/CSAZ/PDAY/PDAZ/PRAY/PRAZ

TABLE OF CONTENTS Page

Dryer Safety ..........................................................................................................2

Tools & Parts .......................................................................................................5

Dimensions/Ciea rances ..............................................................................6

Gas Dryer Installation Requirements ...................................................7

Electric Dryer Installation Requirements .........................................10

Dryer Venting Requirements ..................................................................13

Gas Supply Connection ............................................................................15

Installing Leveling Legs, Coin Slide, and Coin Box .....................17

Electric Dryer Electrical Connections ................................................18

Leveling ..............................................................................................................22

Complete installation ..................................................................................23

Reversing Dryer Door Swing ...................................................................24

Changing to a 30=or 60-Minute Timing Cam .................................25

Maintenance instructions .........................................................................26

if You Need Assistance ..............................................................................26

Electronic Control Setup instructions ...............................................27

TABLE DES MATII_RES Page

S_curit_ de la s_cheuse ..........................................................................32

Outils et pieces ...........................................................................................35

Dimensions/Distances de d_gagement ........................................36

Exigences d'installation pour la s_cheuse a gaz ........................37

Exigences d'installation pour

la s_cheuse _lectrique ...........................................................................40

Exigences concernant r_vacuation

de la s_cheuse ............................................................................................42

Raccordement a la canalisation de gaz .........................................44

Installation des pieds de nivellement, de la glissiere

monnaie et de la caisse a monnaie ..............................................46

Nivellement .....................................................................................................47

Achever I'installation ..................................................................................48

inversion du sens d'ouverture de la porte ......................................49

Installation d'une came de minutage

de 30 ou 60 minutes ..................................................................................50

instructions d'entretien .............................................................................51

Si vous avez besoin d'assistance .......................................................51

Instructions de r_glage du tableau

de commande _lectronique ..................................................................52

W10474273A

W10474274A -SP www.maytagcommerciallaundry.com

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This isthe safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions,

You can be killed or seriously injured if you don't follow

instructions,

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

N|NG - ...i.kof

- Clothes dryer installation must be performed by a qualified installer.

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install aclothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. If flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers, Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

-To reduce the risk of severe injury or death, follow all installation instructions.

-Save these instructions.

[] It is recommended that the owner post, in a prominent location, instructions for the customer's use in the event the customer smells

gas. This information should be obtained from your gas supplier.

[] Post the following warning in a prominent location.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 1

DRYER SAFETY

WARNING: For your safety, the information in this manual must be followed to minimize !

the risk of fire or explosion, or to prevent property damage, personal injury, or death. J

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

=Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

eClear the room, building, or area of all occupants.

=Immediately carl your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

=if you cannot reach your gas supplier, call the fire department.

- installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

in the State of Massachusetts, the following installation instructionsapply:

[] installationsand repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

iMPORTANT: When discarding or storing your old clothes dryer, remove the door. I

DRYER SAFETY

IM PORTANTSAFETY iNSTRUCTiONS

WAR a JNG: To reduce the riskof fire,electricshock, or injuryto persons when using the dryer,follow basic precautions,

includingthe following:

[] Read all instructions before using the dryer.

[] This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

[] WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear the

area. Contact the dryer owner immediately.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-cleaning

solvents, other flammable, or explosive substances as they

give off vapors that could ignite or explode.

[] Do not dry unwashed items in the dryer.

[] Do not alJow chiJdren to play on or in the dryer. Close

supervision of children is necessary when the dryer is used

near chiJdren.

[] Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not open door while dryer is in operation. It will stop.

[] Do not install or store the dryer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

[] Do not use this dryer without the lint screen in place.

[] Do not repair or replace any part of the dryer or attempt any

servicing unless specificaJJy recommended in this InstaJJation

Instructions or in published user-repair instructions that you

understand and have the skills to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] The final part of a tumble dryer cycle occurs without heat

(cooFdown cycle) to ensure that the articles are left at a

temperature that ensures that the items will not be damaged.

[] WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated. (Avoids risk of

spontaneous combustion).

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and dryer exhaust vent should be

cJeaned periodically by quaJified service personnel.

[] See "Electrical Requirements" section for grounding

instructions.

SAVETHESE iNSTRUCTiONS

TOOLS & PARTS

Tools Needed:

8" (203 ram)

or 10" (254 ram)

Pipe Wrench

Torx _÷T-20 Security

Screwdriver or Bit

Level

8" (203 ram) or 10" (254 ram)

Adjustable Wrench

that opens to 1" (25 ram)

Flat-Blade Screwdriver Phillips Screwdriver

t" (25 ram) Hex-Head

Socket Wrench 5/16" (8 ram) Socket Wrench Pliers (that open to

19/16"[39 ram])

Utility Knife 1/4" (6 ram) Nut Driver 27" (686 ram)

Wood Block

Caulk Gun and Caulk Vent Clamps

(for installing new exhaust vent) Pipe-Joint Compound

Suitable for Gas Type U

Putty Knife

Flashlight (optional) 1" (25 ram)

Open-End Wrenches Ruler or Measuring Tape

Parts Supplied:

Foot Boots (4) Leveling Legs (4) Bezel Kit (PR models only)

Security Cone

(PD models only) 5/1 6" Hex Head -

18 x 21/2" Security Bolt

(PD models only)

3-Pin 60-Minute Timing Cam

(CS models only) 6-Pin 30-Minute Timing Cam

(CS models only)

t@ TORX is a registered trademark of Saturn Fasteners, Inc. 5

DIMENSIONS/CLEARANCES

Dimensions

Side View Back View

Clearances

35"

(889 mm)

1 "

(25 ram)

201/4"

.,_---- (743 mm )---------p.

251/2, ------_-

(648 mm)

, 81/4''

101/4''

(260 ram)

(210 ram)

31/4"

(83 mm)

27" -----------_4

¢___I (686 ram) i

i Eloctric-+

_- 13_

(343ram) I

_-11"-_

(279 ram)

11/2"

(:38 mm) -_ !-.,1- 4" dia

! | (102 ram)

* 13. -*

-_1 (330ram)r _- 31/4"

(33ram)

e,e_,_;_e,s)/1048ram)

37"

(940 ram)

(gas models'

Bottom Exhaust

7II

(178 ram)

o o

141/8''

(359 ram)

15"

(381 mm)

0II

(0 mm)--,

Recessed Front View

1°

_L 0II

(0 mm) I ml

(25 mm) --_

Closet Side View

q14"

-_- (356 mm)

GAS DRYER iNSTALLATiON REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in agarage.

Failure to do so can result in death, explosion, or fire,

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

[] A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See "Electrical Requirements_'

[] A level floor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft floor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Gas dryer installation clearances

[] The location must be large enough to allow the dryer door

to be fully opened.

[] Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180 °.

[] Additional clearances might be required for wall, door, and floor

moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

When installing a gas dryer:

IM PORTANT: Observe all governing codes and ordinances.

[] Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

[] Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

"Recessed Area and Closet Installation Instructions" below for

minimum spacing requirements.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in "Dimensions/Clearances:'

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in

the top and bottom is required. Louvered doors with equivalent air

openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same closet

as the dryer.

48 in. 2

(310 cm 2)

Front

View

24 in.2

(155 cm 2)

Closet

Door

(76 m_

GAS DRYER INSTALLATION REQUIREMENTS

Electrical Requirements

Electrical Shock Hazard

Plug into agrounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

iMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1. If codes

permit and a separate ground wire is used, it is recommended that

a qualified electrical installer determine that the ground path is

adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

[] Do not ground to a gas pipe.

[] Do not have a fuse in the neutral or ground circuit.

[] A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

[] This dryer is equipped with a power supply cord having a

3-prong grounding plug.

[] To minimize the possibility of shock, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of

the customer to have the properly grounded outlet installed by

a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

[] Check with a qualified electrician if you are not sure the dryer is

properly grounded.

Gas Dryer Grounding

GROUNDING INSTRUCTIONS

m For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS DRYER iNSTALLATiON REQUIREMENTS

Gas Supply

Explosion Hazard

Use anew CSA International approved gas supply line.

Install a shut=off valve,

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water

column.

Examples of aqualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

M PORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes, installation must conform with

American National Standard, National Fuel Gas Code ANSi

Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certified by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level at

the B.T.U. rating indicated on the model/serial plate. Burner input

adjustments are not required when the dryer is operated up to this

elevation.

When installed above 10,000 feet (3048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing

above 10,000 feet (3048 m) elevation, contact your local service

company.

ELECTRIC DRYER iNSTALLATION REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not instafl in a garage.

Failure to do so can result in death, explosion, or fire.

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

[] A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See "Electrical Requirements:'

[] A level floor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft floor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Electric dryer installation clearances

[] The location must be large enough to allow the dryer door to be

fully opened.

[] Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180 °.

[] Additional clearances might be required for wall, door, and floor

moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in "Dimensions/Clearances_'

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in

the top and bottom is required. Louvered doors with equivalent air

openings are acceptable.

The dryer must be exhausted outdoors.

48 in.2

(310 cm 2}

Front

View

24 in.2

(155 cm 2)

(76 mr

Closet

Door

176_rlm}

Electrical Requirements = U.S.A. only

It is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

[]

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A time

delay fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral or

grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

This manual suits for next models

Table of contents

Languages:

Other Maytag Dryer manuals

Maytag

Maytag MD9206 User manual

Maytag

Maytag Amana NDE2330AYW User manual

Maytag

Maytag MEDC500VW - Centennial Series 29 Inch Electric... User manual

Maytag

Maytag MD-15 User manual

Maytag

Maytag MDE9306AYA User manual

Maytag

Maytag MED9700S - Electric Dryer User manual

Maytag

Maytag Neptune MDE5500AYQ User manual

Maytag

Maytag MDG7400AWQ User manual

Maytag

Maytag MDE3758AZW User manual

Maytag

Maytag MED5800TW - Electric Dryer User manual

Maytag

Maytag MDE2400AY Series User manual

Maytag

Maytag MGDE300VF - Performance Series 27-in Gas... User manual

Maytag

Maytag MLE27PD User manual

Maytag

Maytag 9700 series User manual

Maytag

Maytag MEDZ600TB1 User manual

Maytag

Maytag MDE17MN User manual

Maytag

Maytag MLE/MLG24PR User manual

Maytag

Maytag MLE24PRAY User manual

Maytag

Maytag 30 lb. Stacked Models User manual

Maytag

Maytag MDE18PD User manual

Maytag

Maytag 3395316 User manual

Maytag

Maytag MEDC215EW Installation instructions

Maytag

Maytag MGD7000AW0 User manual

Maytag

Maytag SDE405DAYW User manual

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions