Maytag MDE20PR User manual

www.maytagcommerciallaundry.com

W10868655A

W10868673A – SP

TABLE OF CONTENTS

DRYER SAFETY..................................................................................................2

TOOLS & PARTS ...............................................................................................5

DIMENSIONS/CLEARANCES ................................................................. 6

GAS DRYER INSTALLATION REQUIREMENTS .............................. 7

ELECTRIC DRYER INSTALLATION REQUIREMENTS .............. 10

DRYER VENTING REQUIREMENTS ................................................. 13

GAS SUPPLY CONNECTION ................................................................. 15

INSTALLING LEVELING LEGS, COIN SLIDE, AND

COIN BOX......................................................................................................... 17

ELECTRIC DRYER ELECTRICAL CONNECTIONS ..................... 18

LEVELING ......................................................................................................... 23

COMPLETE INSTALLATION ..................................................................... 24

REVERSING DRYER DOOR SWING ................................................... 25

CHANGING TO A 30- OR 60-MINUTE TIMING CAM ................. 26

MAINTENANCE INSTRUCTIONS ......................................................... 27

IF YOU NEED ASSISTANCE ................................................................... 27

ELECTRONIC CONTROL SETUP INSTRUCTIONS ................... 28

WARRANTY........................................................................................................ 33

TABLE DES MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE ............................................................ 35

OUTILS ET PIÈCES .................................................................................. 38

DIMENSIONS/DISTANCES DE DÉGAGEMENT ...................... 39

EXIGENCES D’INSTALLATION POUR LA

SÉCHEUSE À GAZ..................................................................................... 40

EXIGENCES D’INSTALLATION POUR

LA SÉCHEUSE ÉLECTRIQUE ........................................................... 43

EXIGENCES CONCERNANT L’ÉVACUATION

DE LA SÉCHEUSE .................................................................................... 45

RACCORDEMENT À LA CANALISATION DE GAZ .................... 47

INSTALLATION DES PIEDS DE NIVELLEMENT,

DE LA GLISSIÈRE À MONNAIE ET DE LA CAISSE

À MONNAIE .................................................................................................. 49

NIVELLEMENT ..............................................................................................50

ACHEVER L’INSTALLATION ....................................................................51

INVERSION DU SENS D’OUVERTURE DE

LA PORTE .........................................................................................................52

INSTALLATION D’UNE CAME DE MINUTAGE

DE 30 OU 60 MINUTES ...........................................................................53

INSTRUCTIONS D’ENTRETIEN ...........................................................54

SI VOUS AVEZ BESOIN D’ASSISTANCE ........................................54

INSTRUCTIONS DE RÉGLAGE DU TABLEAU

DE COMMANDE ÉLECTRONIQUE ................................................... 55

GARANTIE.........................................................................................................61

INSTALLATION INSTRUCTIONS

CommerCial Dryer Gas or eleCtriC

INSTRUCTIONS D’INSTALLATION

séCheuse àusaGe CommerCial à Gaz ou éleCtrique

DRYER SAFETY

■It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells

gas. This information should be obtained from your gas supplier.

■Post the following warning in a prominent location.

DRYER SAFETY

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

DRYER SAFETY

■Clean dryer lint screen before or after each load.

■Do not use this dryer without the lint screen in place.

■Do not repair or replace any part of the dryer or attempt any

servicing unless speciﬁcally recommended in this Installation

Instructions or in published user-repair instructions that you

understand and have the skills to carry out.

■Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

■Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

■The ﬁnal part of a tumble dryer cycle occurs without heat

(cool-down cycle) to ensure that the articles are left at a

temperature that ensures that the items will not be damaged.

■WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated. (Avoids risk of

spontaneous combustion).

■Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

■The interior of the dryer and dryer exhaust vent should be

cleaned periodically by qualiﬁed service personnel.

■See “Electrical Requirements” section for grounding

instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

SAVE THESE INSTRUCTIONS

■Read all instructions before using the dryer.

■This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

■WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear the

area. Contact the dryer owner immediately.

■Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch ﬁre.

■Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-cleaning

solvents, other ﬂammable, or explosive substances as they

give off vapors that could ignite or explode.

■Do not dry unwashed items in the dryer.

■Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is used

near children.

■Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

■Do not reach into the dryer if the drum is moving.

■Do not open door while dryer is in operation. It will stop.

■Do not install or store the dryer where it will be exposed to

the weather.

■Do not tamper with controls.

Tools Needed:

8" (203 mm) 8" (203 mm) or 10" (254 mm) Flat-Blade Screwdriver Phillips Screwdriver

or 10" (254 mm) Adjustable Wrench

Pipe Wrench that opens to 1" (25 mm)

Torx®† T-20 Security 1" (25 mm) Hex-Head 5⁄16" (8 mm) Socket Wrench Pliers (that open to

Screwdriver or Bit Socket Wrench 19/16" [39 mm])

Level Utility Knife 1/4" (6 mm) Nut Driver 27" (686 mm)

Wood Block

Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound Putty Knife

(for installing new exhaust vent) Suitable for Gas Type

Flashlight (optional) 1" (25 mm) Ruler or Measuring Tape

Open-End Wrenches

TOOLS & PARTS

Parts Supplied:

Foot Boots (4) Leveling Legs (4) Bezel Kit (PR models only)

Security Cone 5/16" Hex Head – 3-Pin 60-Minute Timing Cam 6-Pin 30-Minute Timing Cam

(PD models only) 18 x 21⁄2" Security Bolt (CS models only) (CS models only)

(PD models only)

†® TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.

DIMENSIONS/CLEARANCES

Side View Back View

Dimensions

Clearances

291/4"

(743 mm)

35"

(889 mm)

81/4"

(210 mm)

(25 mm)

26"

(660 mm)

31/4"

(83 mm)

71/2"

(191 mm)

(0 mm)

15"

(381 mm)

14" max

(356 mm)

(0 mm)

11/2"

(38 mm)

51/2"

(140 mm)

3/4

(273 mm)

371/2"

(953 mm)

(gas models)

41"

(1042 mm)

131/2"

(343 mm)

Electric

Gas

27"

(686 mm)

31/4"

(83 mm)

36"

(914 mm)

(electric models)

4" dia

(102 mm)

131/2"

(343 mm)

Front View, Recessed Opening Side View, Recessed In Closet

(0 mm)

14" max

(356 mm)

(0 mm)

(25 mm)

3"/3"

(76 mm)

3"/3"

(76 mm)

48"2/48"2

(310 cm2)

24"2/24"2

(155 cm2)

15"

(381 mm)

Closet Door to

Front of Dryer

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

■A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■A level ﬂoor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft ﬂoor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Gas dryer installation clearances

■The location must be large enough to allow the dryer door

to be fully opened.

■Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180°.

■Additional clearances might be required for wall, door, and ﬂoor

moldings.

■Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

■Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

■Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

“Recessed Area and Closet Installation Instructions” below for

minimum spacing requirements.

Location Requirements

GAS DRYER INSTALLATION REQUIREMENTS

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in “Dimensions/Clearances.”

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in

the top and bottom is required. The unobstructed opening needs

to be 1 square inch per 1,000 Btu (252 kcal) of gas burner output.

Output on North American gas dryers is typically 22,000 Btu;

however, Canadian dryers may have lower output. Louvered doors

with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same closet

as the dryer.

24 in.2

(155 cm

48 in.2

(310 cm2)3"

(76 mm)

Closet

door

Front

View

Closet

Door

Front

View

Gas Dryer Grounding

IMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1. If codes

permit and a separate ground wire is used, it is recommended that

a qualiﬁed electrical installer determine that the ground path is

adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■Do not ground to a gas pipe.

■Do not have a fuse in the neutral or ground circuit.

■A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

■This dryer is equipped with a power supply cord having a

3-prong grounding plug.

■To minimize the possibility of shock, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of

the customer to have the properly grounded outlet installed by

a qualiﬁed electrician.

■If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the

ground path is adequate.

■Check with a qualiﬁed electrician if you are not sure the dryer is

properly grounded.

GAS DRYER INSTALLATION REQUIREMENTS

Electrical Requirements

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes, installation must conform with

American National Standard, National Fuel Gas Code ANSI

Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certiﬁed by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level at

the B.T.U. rating indicated on the model/serial plate. Burner input

adjustments are not required when the dryer is operated up to this

elevation.

When installed above 10,000 feet (3048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing

above 10,000 feet (3048 m) elevation, contact your local service

company.

Gas Supply

GAS DRYER INSTALLATION REQUIREMENTS

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

■A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■A level ﬂoor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft ﬂoor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Electric dryer installation clearances

■The location must be large enough to allow the dryer door to be

fully opened.

■Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180°.

■Additional clearances might be required for wall, door, and ﬂoor

moldings.

■Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in “Dimensions/Clearances.”

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in

the top and bottom is required. Louvered doors with equivalent air

openings are acceptable.

Location Requirements

The dryer must be exhausted outdoors.

24 in.2

(155 cm

48 in.2

(310 cm2)3"

(76 mm)

(76 mm

)

Closet

door

Front

View

ELECTRIC DRYER INSTALLATION REQUIREMENTS

Closet

Door

Front

View

Electrical Requirements – U.S.A. only

It is your responsibility:

■To contact a qualiﬁed electrical installer.

■To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

■The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

■A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if speciﬁed on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A time

delay fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral or

grounding circuit.

■Do not use an extension cord.

■If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

This manual suits for next models

Table of contents

Languages:

Other Maytag Dryer manuals

Maytag

Maytag MGD6200KW User manual

Maytag

Maytag W10097007A-SP Owner's manual

Maytag

Maytag Bravos W10160250A User manual

Maytag

Maytag MD-31 User manual

Maytag

Maytag Bravos W10201177B User manual

Maytag

Maytag MLG-45PDB User manual

Maytag

Maytag 3RMED4905TW0 User manual

Maytag

Maytag MHW5630HW User manual

Maytag

Maytag W10057349A User manual

Maytag

Maytag MEDE300VF0 User manual

Maytag

Maytag MGD3000BW User manual

Maytag

Maytag 3RLGR5437 User manual

Maytag

Maytag MED5720TQ0 User manual

Maytag

Maytag MDG16MN User manual

Maytag

Maytag MDG30PCC User manual

Maytag

Maytag NEPTUNE MD68 User manual

Maytag

Maytag MEDE500VW - Performance Series 27 Inch Electric... User manual

Maytag

Maytag SDE305W User manual

Maytag

Maytag MLG35 User manual

Maytag

Maytag MEDX550XW User manual

Maytag

Maytag W10099060 User manual

Maytag

Maytag MGDE400XW User manual

Maytag

Maytag MED5900TW - R CentennialR Electric Dryer Operating and installation instructions

Maytag

Maytag W10057351A User manual

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions