M-system R6S-TS2 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7781-BI Rev.3 P. 1 / 4

INSTRUCTION MANUAL

THERMOCOUPLE INPUT MODULE, 2 points

(Tension clamp) MODEL R6S-TS2

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Thermocouple input module...............................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

The unit is programmable using the PC Conﬁgurator Soft-

ware. For detailed information on the PC conﬁguration,

refer to the R6CON users manual. The R6CON PC Con-

ﬁgurator Software is downloadable at M-System’s web site:

http://www.m-system.co.jp

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•The equipment must be mounted inside a panel.

•Insert a noise ﬁlter for the input and communication line

connected to the unit. NEC TOKIN Model ESD-SR-250

or equivalent is recommended.

•The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

•Install lightning surge protectors for those wires connect-

ed to remote locations.

■HOT INSERTION/REMOVAL OF MODULES

•Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■GENERAL PRECAUTIONS

•Do NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Specifications

Body

Front Cover

Mounting Adaptor

INSTALLATION

Mount the unit on the base (model: R6S-BS).

R6S-TS2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7781-BI Rev.3 P. 2 / 4

EXTERNAL VIEWS

• Front View (cover opened) • Side View

5678

1234

SW3

SW2

SW1

2345678

OFF

SW3

SW2

SW1

Module Address

Setting

Operating Mode

Setting

Status LED

Power LED

■INDICATOR LED

ID COLOR FUNCTION

Power OFF Power supply is off

Green ON Power supply is on.

Status OFF Standing by (at the startup)

or communication error

Green ON Normal communication

Green blink Conﬁguration mode

Red ON DIP switch error

Red blink

2 sec. interval

Parameter error

Red blink

0.5 sec. interval

Burnout

■MODULE ADDRESS

Module address is selectable between 0 and 31. Choose 0 or

16 with SW1 for offsetting the address selected with SW2 (0

to F, hexadecimal).

The module’s slot position on the base and the module ad-

dress are not necessarily correlated.

ADDRESS SW1 SW2 ADDRESS SW1 SW2

0 0 0 16 16 0

1 0 1 17 16 1

2 0 2 18 16 2

3 0 3 19 16 3

4 0 4 20 16 4

5 0 5 21 16 5

6 0 6 22 16 6

7 0 7 23 16 7

8 0 8 24 16 8

9 0 9 25 16 9

10 0 A 26 16 A

11 0 B 27 16 B

12 0 C 28 16 C

13 0 D 29 16 D

14 0 E 30 16 E

15 0 F 31 16 F

■OPERATING MODE

(*) Factory setting

• Thermocouple Type

T/C

INPUT 1 INPUT 2

SW3 SW3

123456

K (CA) (*)

E (CRC) ■ ■

J (IC) ■ ■

T (CC) ■ ■ ■ ■

B (RH) ■ ■

R■ ■ ■ ■

S■ ■ ■ ■

C (WRe 5-26) ■■■■■■

Use PC Conﬁgurator Software (model: R6CON) to set N, U,

L, P (Platinel II) and PR thermocouples.

■= ON, Blank = OFF

• Burnout

BURNOUT SW3-7

Upscale (*)

Downscale ■

■= ON, Blank = OFF

• Conguration Mode

CONFIGURATION MODE SW3-8

DIP SW (*)

PC ■

■= ON, Blank = OFF

R6S-TS2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7781-BI Rev.3 P. 3 / 4

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

94 (3.70)

5.9 (.23)

*Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm

102 (4.02)

WIRE INSERTION ANGLE

: approx.35°

TEST PROBE

max. 2 (.08) dia.

SCREWDRIVER

INSERTION ANGLE

: approx. 35°

5678

1234

■CONNECTION DIAGRAM

BUS CONNECTOR

INTERNAL

POWER

INTERNAL

BUS

INPUT 1

INPUT 2

–

T/C

comp. leadwire

–

T/C

comp. leadwire

–

• Unused Input Channels

Close across the unused input terminals as shown below.

(Choose K (CA) thermocouple for unused channels.)

INPUT 1

INPUT 2

Short

If unused input terminals are not short-circuited, status in-

dicator LED blinks in red (0.5 sec. cycle), and a burnout ﬂag

is set in the PLC or the host device.

■WIRING INSTRUCTIONS

•Applicable wire size

Solid: 0.2 to 2.5 mm2(0.55 to 1.75 dia.)

Stranded: 0.2 to 2.5 mm2(Tinning wire ends may cause

contact failure and therefore is not recom-

mended.)

Ferruled: 0.2 to 1.5 mm2(0.55 to 1.35 dia.)

•Expose wire conductors by 8 mm (0.31”).

• How to Connect Wires

Screwdriver

Wire

R6S-TS2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7781-BI Rev.3 P. 4 / 4

1) Insert a minus screwdriver into the wire entry opening,

between the clamp and the housing, until its tip hits the

bottom where it is ﬁrmly held.

Tension Clamp

Screwdriver

2) Insert a wire. Push the screwdriver toward the direction

indicated with the arrow in the ﬁgure below to widen the

opening if necessary.

Wire Entry

Wire

3) Conﬁrm that the wire tip hits the bottom and pull out the

screwdriver in holding it in position.

Conﬁrm that the wire’s insulation tube is not caught in

the clamp.

PC CONFIGURATOR

With conﬁgurator software, settings shown below are avail-

able.

Refer to the software manual of R6CON for detailed opera-

tion.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE

DEFAULT SETTING

Sensor type K (CA)

E (CRC)

J (IC)

T (CC)

B (RH)

C (WRe 5-26)

P (Platinel II)

(PR)

K (CA)

Lower range value Depends on sensor type 0.00 (degC)

Upper range value Depends on sensor type 0.00 (degC)

Fine zero adjustment -320.00 to +320.00 (%) 0.00 (%)

Fine gain adjustment -3.2000 to +3.2000 1.0000

Scaled range Zero -32000 to +32000 0

Scaled range Span -32000 to +32000 10000

Burnout Upscale, Downscale Upscale

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE

DEFAULT SETTING

Loss of internal bus

communication detec-

tion time

0.0 – 99.9 (sec.) 1.0 (sec.)

Conversion rate 250, 500 (msec.) 500 (msec.)

Temperature unit degC, degF, K degC

CJC ON, OFF ON

Limit -15 to +115%

Scaled range Zero / Span

-15 to +115%

Other M-system Control Unit manuals

M-system

M-system R7L-EC16B User manual

M-system

M-system R1D-GH2 User manual

M-system

M-system R3-PA8 User manual

M-system

M-system R6N-RS2 User manual

M-system

M-system R7 Series User manual

M-system

M-system R7L-SV4-R User manual

M-system

M-system R3-SV8B User manual

M-system

M-system R7M-YS2 User manual

M-system

M-system R7G4FML3-6-DC16A User manual

M-system

M-system R3-NC2 User manual

M-system

M-system R3-NMW1F User manual

M-system

M-system R7C-EA8 User manual

M-system

M-system R7ML-DC16D User manual

M-system

M-system TR3EX User manual

M-system

M-system R7L-EC8A User manual

M-system

M-system R7M-DA16 User manual

M-system

M-system R6-NP1 User manual

M-system

M-system R7ML-DC16B User manual

M-system

M-system R3-PD16B User manual

M-system

M-system R7C-EC16A User manual

M-system

M-system R7ML-EA16 User manual

M-system

M-system R7C-DC16B User manual

M-system

M-system M6DXF1 User manual

M-system

M-system R7ML-EC8A User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual