M-system R6-NP1 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 1 / 4

INSTRUCTION MANUAL

PROFIBUS-DP INTERFACE MODULE

(for 62-point analog signals) MODEL R6-NP1

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Network interface module ..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

■GSD FILE

GSD ﬁles are downloadable at M-System’s web site: http://

www.m-system.co.jp

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT INSERTION/REMOVAL OF MODULES

• It is possible to replace the module with the power is sup-

plied. Be sure to replace it when the module is not com-

municating with a host, as it is possible to affect the sys-

tem. However, replacing multiple modules at once may

greatly change line voltage levels. We recommend that

you replace them one by one.

■GENERAL PRECAUTIONS

• Do not set the DIP switch on the side panel while the

power is supplied. The DIP switch is selectable for main-

tenance without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

R6-NP1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 2 / 4

INSTALLATION

Use the Base Model R6x-BSA or R6x-BSB.

Before mounting the Network Interface Module onto the Base, be sure to conﬁgure the module as explained below.

■Station No.

See “COMPONENT IDENTIFICATION.”

Station No. is selectable from 00 to 7D via the front rotary

switches. It is programmed to 7D if a larger number is set

on the switches.

■NETWORK SLOTS ON THE BASE

Mount the Network Module to the dedicated slot on the

base.

• R6x-BSA

The I/O and the power (model: R6x-PF1) modules can be

positioned freely on whichever among the slots 1 through 8.

Set a module address to each I/O module.

123 ・・・ 8

Network

Module

I/O & Power Supply

Modules

• R6x-BSB

The power module (model: R6-PSM) should be located on

the extreme left, the I/O modules can be positioned freely

on whichever among the slots 1 through 8. Set a module

address to each I/O module.

Power Supply

Module

I/O Modules

23 ・・・8

Network

Module

R6-NP1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 3 / 4

COMPONENT IDENTIFICATION

ERR Indicator LED

Configuration Jack

Station No. Setting

Rotary SW, lower digit

Network Connector

Station No. Setting

Rotary SW, upper digit

RUN Indicator LED

■PROFIBUS INTERFACE

PIN NO. SIGNAL SIGNIFICANCE

1 NC Not used

2 NC Not used

3 B_ine Network, B-line

4 RTS RTS signal

5 GND 0V

6 P5V 5V

7 NC Not used

8 A_line Network, A-line

9 NC Not used

■FRONT ROTARY SW

• Station No.: SA1, SA2

Station No. is set in Hexadecimal.

(Setpoint adjustment: 00 – 7D)

■INDICATOR LED

ID S TAT E EXPLANATION

RUN

Green ON Transmitting

Green blinking Data hold

OFF Communication error

Red ON Hardware error

ERR

OFF Normal operating

Transmitting

Green ON/

blinking I/O module error

Red ON No master

Red blinking Address error

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R6CON for detailed operation.

■INTERFACE MODULE SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Card map 1 to 31 1 to 31

R6-NP1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 4 / 4

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

90 (3.54) 5.6

(.22)

90 (3.54) LOCKING CLAMP

POSITIONING GUIDE

18 (.71)

■CONNECTION DIAGRAM

INTERNAL POWER

INTERNAL BUS

CONFIGURATION JACK

JACK

BUS CONNECTOR

PROFIBUS

D-SUB CONNECTOR

I/O DATA DESCRIPTIONS

• 16-bit Analog Data

0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data. For example, 135.4°F is con-

verted into 135.

Negative values are represented in 2’s complements.

015

• Discrete Data

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

Input 4 (Output 4)

Not Used (Remains “0”)

0 : OFF

1 : ON

015

Other M-system Control Unit manuals

M-system

M-system R80FST4NJ User manual

M-system

M-system R3-NM4 User manual

M-system

M-system R7M-DAC16C User manual

M-system

M-system R7L-EC8B User manual

M-system

M-system Devicenet R7F4HD-DAC32D User manual

M-system

M-system R7C-EC8C User manual

M-system

M-system R8-NECT1 User manual

M-system

M-system R7ML-YV2 User manual

M-system

M-system Devicenet R7F4HD-DAC32C User manual

M-system

M-system R7L-RR8 User manual

M-system

M-system R3Y-PA16 User manual

M-system

M-system R30US2 User manual

M-system

M-system R7M-DC16A User manual

M-system

M-system M8YC User manual

M-system

M-system R3-RS8 User manual

M-system

M-system EtherCAT R7I4DECT-1-PA8A User manual

M-system

M-system M6SXF3 User manual

M-system

M-system R3-NC2 User manual

M-system

M-system R3-PD16A User manual

M-system

M-system R3Y-SS8N User manual

M-system

M-system R7ML-EC8A User manual

M-system

M-system R3-GC1 User manual

M-system

M-system R7C-EC16A User manual

M-system

M-system R7ML-DC16D User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual