M-system R3-AV4 User manual

R3-AV4

P. 1 / 3 EM-8435 Rev.1

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

DC voltage input alarm module ................................. (1)

■ MODEL NO.

Check that model No. described on the specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

INSTRUCTION MANUAL

MODEL R3-AV4

DC VOLTAGE INPUT ALARM MODULE

(4 points, isolated)

POINTS OF CAUTION

■ CONFORMITY WITH EC DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

figurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated in

a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■ HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other modules

on the same backplane. It is possible to replace them without

removing the power supply. However, replacing multiple

modules at once may greatly change line voltage levels. We

recommend that you replace them one by one.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufficient ventila-

tion.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ UNUSED INPUT CHANNELS

• Set the unused input channels to ±10V range. Unused

channels left open with other settings may be equal to the

input lower than -15%, which sets a data abnormality at the

PLC or the host device.

Open circuit with the input range set to ±10V means 50% of

the full-scale. An alarm setpoint must be set to a value that

does not trip an unwanted alarm.

• Unused channels can be specified and set so on the PC

Configurator Software (model: R3CON) without needing the

above mentioned setting.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-AV4

P. 2 / 3 EM-8435 Rev.1

COMPONENT IDENTIFICATION

•Conversion Rate: SW3

SW CONVERSION RATE

80 ms (*)40 ms 20 ms 10 ms

SW3-1 OFF ON OFF ON

SW3-2 OFF OFF ON ON

(*) Factory setting

SW1SW2

SW3

■FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Conv.

Rate

Input 2 (SW1)

Input 4 (SW2)

Range

Input 1 (SW1)

Input 3 (SW2)

■SIDE DIP SW

•Input Range: SW1, SW2

INPUT 1 (SW1) INPUT 2 (SW1)

INPUT 3 (SW2) INPUT 4 (SW2) RANGE

12345678

OFF OFF OFF OFF OFF OFF OFF OFF

-10 – +10V

(*)

ON OFF OFF OFF ON OFF OFF OFF -5 – +5V

OFF ON OFF OFF OFF ON OFF OFF -1 – +1V

ON ON OFF OFF ON ON OFF OFF 0 – 10V

OFF OFF ON OFF OFF OFF ON OFF 0 – 5V

ON OFF ON OFF ON OFF ON OFF 1 – 5V

OFF ON ON OFF OFF ON ON OFF 0 – 1V

OUTPUT DATA DESCRIPTIONS

Four alarm setpoints are selectable per each input. One (1)

word (16 bit) data is transmitterd to the PLC or the host

device via the R3 network module.

Alarm 1

Alarm 2 Input 1

Alarm 3

Alarm 4

Alarm 1

Alarm 2 Input 2

Alarm 3

Alarm 4

Alarm 1

Alarm 2 Input 3

Alarm 3

Alarm 4

Alarm 1

Alarm 2 Input 4

Alarm 3

Alarm 4

ALARM SETTING

The following parameters are programmable using the PC

Configurator Software (model: R3CON).

■ALARMTRIP POINT (-15.00 to +115.00%)

Four alarm setpoints are selectable per each input.

■ALARM TYPE (High or Low)

High or Low alarm is selectable for each alarm trip point.

High alarm: An alarm is set when the input signal goes above

the setpoint.

Low alarm: An alarm is set when the input signal goes be-

low the setpoint.

■DEADBAND (HYSTERESIS)

(0.00 to 100.00%; factory set to 5.00)

Deadband (deviation between the points where the alarm is

set and reset) is selectable for each alarm trip point.

■POWER ON DELAY TIME

(0.0 to 99.0 seconds; factory set to 5.0)

The alarm output start functioning in the preset time after

the power has been turned on.

This setting is common to all four points.

■ALARM ON DELAY TIME

(0.0 to 99.0 seconds; factory set to 1.0)

The alarm output is set when the preset time elapses after

the input has entered in the alarm range.

This setting is common to all four points.

■ALARM HOLD TIME

(0.0 to 99.0 seconds; factory set to 1.0)

The alarm output is held for the preset time even if it is

reset in shorter time.

This setting is common to all four points.

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the input abnormality;

Green in normal operating conditions.

R3-AV4

P. 3 / 3 EM-8435 Rev.1

■ DIMENSIONS mm (inch)

■ CONNECTION DIAGRAM

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

WIRING INSTRUCTIONS

■SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solderless

terminals with insulation sleeve do not fit. Applicable wire

size: 0.3 – 0.75 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

INPUT 1

–

NARROW SPAN

WIDE SPAN

INTERNAL POWER

BUS A

BUS B*

*For dual redundant communication.

NOTE: Connect either wide or narrow span terminals for each channel.

BUS CONNECTOR

INPUT 2

–

NARROW SPAN

WIDE SPAN

INPUT 3

–

NARROW SPAN

WIDE SPAN

INPUT 4

–

NARROW SPAN

WIDE SPAN

Other M-system Control Unit manuals

M-system

M-system EtherCAT R7I4DECT-1-PA8A User manual

M-system

M-system 61A User manual

M-system

M-system R3Y-SS8 User manual

M-system

M-system R7ML-EC8A User manual

M-system

M-system R3Y-DS8N User manual

M-system

M-system R5-PA2 User manual

M-system

M-system R3-NC1 User manual

M-system

M-system R8-SVT8 User manual

M-system

M-system R7C-RS4 User manual

M-system

M-system R3-NP1 User manual

M-system

M-system R7C-EC8C User manual

M-system

M-system M6NPS1 User manual

M-system

M-system R3-PA2 User manual

M-system

M-system R7ML-EC16A User manual

M-system

M-system R3-NC3 User manual

M-system

M-system R7L-YS2 User manual

M-system

M-system R7M-CT4E User manual

M-system

M-system Mini-M M2DL User manual

M-system

M-system R3-NMW1F User manual

M-system

M-system R7C-YS2 User manual

M-system

M-system R7HL-DC16A User manual

M-system

M-system Devicenet R7F4HD-DAC32D User manual

M-system

M-system R7HL-TS4 User manual

M-system

M-system R3-NL1 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual