Linear Technology LT1374CFE User manual

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 474

4A, 500KHZ STEP DOWN SWITCHING REGULATOR

LT1374CFE

DESCRIPTION

Demonstration circuit 474 is a step-

down buck regulator using the

LT1374CFE 500kHz-switching regulator.

The high switching frequency allows

the use of small inductors and filter

components, making this circuit ideal

for space conscious systems.

0.8

0.85

0.9

0.95

012345

Load Current

Efficiency

Figure 1. Efficiency, 10V V

, 5V V

OUT

Figure 1 shows efficiency versus load

for a typical application. The best

efficiency is realized with a load

current between 700mA and 2 amps.

Full load efficiency is 87%. The

maximum allowed die temperature is

125°C. Figure 2 shows die temperature

vs. output load current with V

12V. At full load the die temperature

rise is 70°C indicating that the demo

is suitable for ambient temperatures

of up to 125°C – 70°C = 55°C.

0123

Load (Amps)

Tem perature (Degrees C)

Figure 2. Die Temperature vs Output

Current, V

= 12V

QUICK START PROCEDURE

Refer to Figure 3 for proper measure-

ment equipment setup and follow the

procedure below:

Connect input power to the Vin and

GND terminals. V

should be be-

tween 5V and 25V. The power source

should be capable of delivering

25W.

NOTE:

5V output operation requires

a minimum V

of 6V

Connect the output load to the Vout

and GND terminals.

Select desired output voltage using

the voltage selecting jumper

NOTE:

Choose 3.3V operation by mov-

ing the voltage selection jumper to

the 3.3V position. Demonstration

circuit 474 is optimized for 5V op-

eration, and when operating at 3.3V

out, high V

and light load some

instability may arise. Increasing

the output capacitance removes this

instability. Use a 330µF, 4V, low

ESR cap such as the “Poscap” or

“Oscon”.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 474

4A, 500KHZ STEP DOWN SWITCHING REGULATOR

To turn the circuit off, ground the

terminal labeled SHDN

To test the synchronization feature

of the demo board apply a sync sig-

nal to the sync terminal and note

the shift in the operating fre-

quency. The Sync signal should have

an amplitude greater than 2.2V,

duty cycle of between 10% and 90%

and a frequency of 580kHz–1000kHz

MEASUREMENT NOTES

Voltage measurements

The correct way to measure voltage is

at the terminal of the demo board.

Attempts to measure output voltage at

the load will result in a too low

output voltage due to wiring loss.

This is especially true at high cur-

rent. Needless to say any efficiency

calculation should be made using demo

circuit terminal voltages as opposed

to load or power source terminal

voltages.

Ripple Voltage Measurements

The ceramic capacitors used in this

demo board have almost no ESR and are

extremely effective filters. In order

to correctly measure output ripple

voltage correct technique is impor-

tant. The scope ground lead and

sheath should be removed and the out-

put ripple measured by placing the

scope probe directly across the out-

put Vout and GND pins as illustrated

in Figure 4.

5V TO 25V

SUPPLY

25W

–

–+

–

LOAD

Figure 3. Proper Measurement Equipment Setup

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 474

4A, 500KHZ STEP DOWN SWITCHING REGULATOR

VIN

GND

Figure 4. Scope Probe Placement for Measuring Output Ripple

Other Linear Technology Controllers manuals

Linear Technology

Linear Technology DC2268A-1 Quick setup guide

Linear Technology

Linear Technology DC1041A-A Quick setup guide

Linear Technology

Linear Technology DC1989A-A Quick setup guide

Linear Technology

Linear Technology DC1936A Quick setup guide

Linear Technology

Linear Technology LTM8032 Quick setup guide

Linear Technology

Linear Technology DC1736A Quick setup guide

Linear Technology

Linear Technology Analog Devices LT8708 User manual

Linear Technology

Linear Technology LT3091EDE Quick setup guide

Linear Technology

Linear Technology LT8570 Quick setup guide

Linear Technology

Linear Technology LTC3210-2 User manual

Linear Technology

Linear Technology LTC4231 Quick setup guide

Linear Technology

Linear Technology LINEARCOM3000 LC3.IRTX User manual

Linear Technology

Linear Technology 1158A User manual

Linear Technology

Linear Technology DC1084A-B User manual

Linear Technology

Linear Technology LTC3875EUJ Quick setup guide

Linear Technology

Linear Technology LT3081 User manual

Linear Technology

Linear Technology LT3480 User manual

Linear Technology

Linear Technology LTC1877 Quick setup guide

Linear Technology

Linear Technology LTC4260 User manual

Linear Technology

Linear Technology LT8609 User manual

Linear Technology

Linear Technology LT3695 Series User manual

Linear Technology

Linear Technology LTC4080 User manual

Linear Technology

Linear Technology LTM4624EY User manual

Linear Technology

Linear Technology DC1865A Quick setup guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual