Life Smart LS-4W1500-X Quick start guide

LIFESMART Infrared Heater

Model

: LS-4W1500-X

Safety Notice

Please read this entire Installation and Operating Manual BEFORE installing and using

your new Infrared Heater. Failure to fully understand and follow instructions may result in

property damage, bodily injury, or even death.

If the Infrared Heater in not used properly, a house fire may result. For everyone’s safety,

FOLLOW all Installation and Operating Directions.

Save These Instructions

TABLE OF CONTENTS

Topic Page(s)

Introduction & Specifications 3

Important Safety Information 4-5

Frequently Asked Questions 6-9

Heater Operation 9

Heater Placement 10

Users Guide 11-12

Air Filter Maintenance 12

Warranty 13-14

Warranty Claim Contact Information 15

*Contents in the box:

1. Infrared heater

2. Instruction manual

3. Remote control (2 AAA batteries not included)

INTRODUCTION

Thank you for choosing one of the best Infrared distribution heaters available on the market today.

Our Infrared Heater is a very safe and effective room heater. It produces safe, clean and

economical heat by utilizing quartz infrared heating elements. The heating process of the Infrared

Heater is similar to the way the sun warms the earth. The infrared elements warm the heat

chamber and the whisper quiet fan distributes the accumulated warmth. This process is unique

among heaters in that it minimizes wasteful heat collection at the ceiling height of rooms and

targets it toward the living space instead. Thank you for being our customer, and enjoy your

heater!

Our Infrared Heaters have been tested and listed for installation in residential and mobile homes

by ETL:

3189533

Conforms to UL STD. NO.1278

Certified to CSA STD. C22.2 NO.46

SPECIFICATIONS:

Electrical:

Voltage: 120V~60Hz,

Power consumption: 750/1500 Watts

Thermostat range: 50-90 Fahrenheit

Coverage:

Up to 1500 square feet of unobstructed area

Dimensions:

16.5” x 13.2” x 16.5”, 26 lbs

Safety features:

Advanced Safety Overheat Shut Off

Tip Over Shut Off

Features:

Remote Control

High/Low/Eco Heat Settings

Air filtration system

Lifetime Washable Filter

On/Off Timer

Eco Friendly Wood

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS, SAFETY WARNINGS,

AND FAQ’s BEFORE USING THE HEATER

WARNING!

! POTENTIAL FOR ELECTRICAL HAZARD IF NOT ADHERED TO!

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing

else can be plugged into the same circuit. If unsure if your home meets this

specification, consult a certified electrician prior to use. Risk of fire, overheat,

malfunction, property damage, injury, or even death may result if not adhered to!

2. Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to

extension cords, surge protectors, timers, direct breakers, or an outlet with other

appliances connected to the same outlet. Risk of fire, overheat, malfunction,

property damage, injury, or even death may result if not adhered to!

3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

Use handles (certain models) or wheels to move this heater.

4. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and

curtains from the front of the heater and keep them away from the sides and rear of the

heater.

5. Extreme caution is necessary when any heater is used by or near children, invalids,

pets, or when the heater is left operating unattended.

6. Always unplug the heater when not in use.

7. Do not operate any heater with a damaged cord or plug or after the heater malfunctions,

has been dropped, or damaged in any manner. Contact the manufacturer for resolution

options.

8. Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind or

extreme temperatures may cause the heater to become a safety hazard.

9. This heater is not intended for use in bathrooms, laundry areas and similar indoor

locations, nor any locations that use GFCI outlets.

10.Never place heater where it may fall into a bathtub or other water receptacles.

11.Do not run cord under carpet. Do not cover cord with throw rugs, runners, or similar

coverings. Arrange cord away from traffic area and where it will not be tripped over.

12.The heater must be plugged into a wall outlet that is a DEDICATED CIRCUIT, with a

minimum 15 amp rating on that individual circuit.

13.To disconnect the heater: FIRST, turn the power button to the “off” position, then

remove plug from the wall outlet.

14.Do not allow foreign objects to enter or block any ventilation or exhaust opening as this

may cause an electric shock or fire, or damage the heater.

15.Allow at least 3 feet of unobstructed space to the front and rear of the heater to allow for

maximum heat, air, and ventilation flow.

16.A heater has hot and arcing or sparking parts inside. Do not use it in areas where

gasoline, paint, or flammable liquids are used or stored, nor use flammable solvents to

clean the heater. Also, make sure to keep heater dry at all times.

17.Use this heater only as described in this manual. Any other use not recommended by

the manufacturer may cause fire, electric shock, or injury to persons.

18.Do not use abrasive solvents to clean the heater as it may cause damage to the finish

or casing.

PLEASE REVIEW FREQUENTLY ASKED QUESTIONS ON THE NEXT

FEW PAGES PRIOR TO USING YOUR HEATER.

FREQUENTLY ASKED QUESTIONS (FAQ’S)

My heater emits a “strange” odor when I first open the box/when I turn the heater on for the first

time. Why?

These are both normal. This heater is treated with a special heat safe/resistant coating. This

odor will sometimes be present when the box is opened, and may be compared to a heaters version

of “new car smell.” Also, similar to all hearth appliances (woodstoves, etc.), the coating, exposed to

heat, will produce this particular odor during the first few hours of operation. This will dissipate after

the break-in period. If you are sensitive to odors, you may want to pre-burn the unit in a garage

with the door open until the initial odor dissipates.

If my heater runs on approximately 15 watts, how many BTU’s is that? Is that a lot of heat?

At 1500 Watts, your heater will use approximately 5100 BTUs. 5100 BTUs, compared to your home

furnace, is a very small amount of heat. It may take several minutes, to several hours to heat your

area, depending on various factors (see Heater Placement).

Can my heater really operate on less money per day? What are my operating costs?

Most Definitely. If the heater is used as it is intended (as supplement/assist heat), it should cycle on

and off, allowing for it to heat a total of approximately 8 out of the 24 hours of the day. Using the

national average of approximately 10¢ per kWh (look at your bill for exact cost per kWh--will vary per

state), your average heating cost should be less per day compared to your main furnace. The costs

will increase if it is used as the single source of heat, or if heat somehow escapes the room being

heated, since the “on” cycle will run longer.

The Formula: To determine the cost of this or ANY 1500 watt appliance, multiply 1.5 X your cost per

Kilowatt Hour. You can find the cost per KWH for your state at:

http://www.eia.doe.gov/fuelelectric.html

What is the life expectancy for the Heating Elements? Can the heating elements be replaced?

The life expectancy of the heating elements is typically 25,000 hours. Heating elements may be

replaced by obtaining parts from LIFESMART Products, although it is not recommended (unless you

are a certified heater technician or authorized directly by LIFESMART). All parts may be purchased

through LIFESMART PRODUCTS if your product is out of warranty. Note: If you feel that the

elements are definitely faulty right out of the box, contact LIFESMART Products Tech Support first

(for troubleshooting). Contact your place of purchase second.

Once I plug the unit in and turn it on, how long will it take to heat my room?

Typically it takes about ½ hour to feel a temperature change. Please remember that with any type of

heating process, there are many variables: Location (in the home), floor plan and size of the room,

how well the room is insulated, how many doors/windows, how much bare concrete (acts as a heat

sink with any type of heating), the opening and closing of an exterior door, long hallways, high

ceilings, etc. Customers with smaller rooms experience quick heat changes. Others with larger and

open floor plans can expect up to 24 hours to heat up.

I don’t have a grounded outlet; can I use adapters, a 2-prong power strip, or remove the ground

prong from the cord?

Definitely NOT! If you don’t have a grounded outlet, contact a certified electrician for advice.

Removing or altering any part of the heater’s original design or intent (including the power cord) will

not only void the warranty, but will make you liable for any unexpected or hazardous results.

Why doesn’t the temperature on my heater match the temperature display on my wall, or external

thermostat?

This is completely normal. The temperature display on your heater may vary from the temperature

display on another thermostat (like the one mounted to your wall or a purchased external

thermostat). The temperature sensor on your heater reads the temperature in, and around, the

heater. The unit is near the cold floor (and heat rises), which in turn, will display a cooler temperature

than elevated or external thermostats. The best way to operate your heater is just to set the unit on

“High” and dial up to a temperature that feels comfortable to you. Then, leave it at that temperature,

regardless of the mismatch. The heater will cycle off when the set temperature is met or exceeded

slightly.

I don’t have a grounded outlet; can I use adapters, a 2-prong power strip, or remove the ground

prong from the cord?

Definitely NOT! If you don’t have a grounded outlet, contact a certified electrician for advice.

Removing or altering any part of the heater’s original design or intent (including the power cord) will

not only void the warranty, but will make you liable for any unexpected or hazardous results.

My home is not insulated very well, will this heater help me? Can I use the heater if I have vaulted

or cathedral ceilings? I live in a structure that is more than 15 square feet. Will this heater help

me? Can I use the heater to heat multiple rooms at the same time? Will I be able to use the heater

in a basement or garage?

The answer to these is the same. Yes. You will be able to use it, but keep in mind that

rooms/structures with open floor plans, minimal insulation, adjacent rooms, or high ceilings will not

retain the heat as efficiently, and may not feel pronounced heat changes. Also, the heater will stay on

longer (delays the “off” cycle), and may increase your electric costs. Note that if you do use it in a

garage or basement, the moisture levels must be very low and they must have dedicated circuits (15

amps minimum) with no GFCI outlets. If unsure what a GFCI outlet is, contact a certified electrician.

Can I use more than one heater at a time? Can I use the heater and another appliance at the same

time?

Yes. But make sure they are not plugged into the same circuit. Each heater (heaters are considered

appliances) requires its own minimum 15 amp circuit (with no other items plugged into that

circuit). If unsure your circuit meets these requirements, verify with a certified electrician. Risk of

fire, damage to property, or injury may result if requirements are not met.

Why does my heater’s fan continue to run even after the set temperature is reached or the power is

turned off?

This is normal. The heater’s fan will continue to run, even after the heater automatically cycles

down. The fan continues to run so that every last bit of heat is blown out of the heat chamber, while

allowing the unit to continue filtering your air. Once the internal box/components cool completely, the

fan should then shut off on its own.

My fan runs at all times, even when the heat has cycled off. Why?

This is normal. Although the heat cycles off, the fan stays on until the chamber is cool. If the

temperature falls below the desired set temperature during the time the fan is cooling, the heating

elements will cycle back on. This will not allow for the fan to completely cool off the chamber, and

shut down. The fan seems to run continuously. It is a safety mechanism to prevent overheating. The

best way to avoid this is to have the set temperature at least 5 degrees higher than the desired heat,

so that it retains that heat during the cooling cycle.

Why doesn’t the fan speed increase when I change the setting from LO to HI?

This is normal. The heater’s fan’s speed is not affected by the HI/LO settings. The fan is designed

to vent the heat at one soft, comfortable, and energy efficient speed. What is affected by the HI

setting is the heat output. In essence, in the HI mode, the heater produces “more” heat, rather than

“faster” heat.

I want to make sure my warranty is registered. What do I send to make sure it is registered? Where

do I send it?

The heater comes with an automatic 1 year limited manufacturer’s warranty at the time of purchase.

Your receipt is considered your proof of purchase and registration. Keep it in a safe place. As long

as it is legible, a copy may be used for any future warranty claims (if requested). If you have access

to e-mail, and would like peace of mind, e-mail us to: Registration @lifesmartproducts.com. In the

body of the e-mail, include your full name, address, phone number, model, serial number, and

scanned copy of your legible receipt. Or you can register online on the registration tab of

www.lifesmartproducts.com.

My heater does not perform as well as another brand heater that I purchased. Why Not?

There are many brands of heaters on the market. Each brand is designed with different heat

specifications, fan speeds, colors, material types, displays, and electrical components. They are

manufactured this way for you, as the consumer to have choices, selection, and preferences. As long

as the unit functions as specifications indicate, comparison to other brands will ultimately depend on

individual consumer perception.

I purchased my heater so that it could cut my heating costs, but my electric bill has gone up. Why?

The compact LIFESMART heater can definitely save you on heating costs, when compared to the

existing central heating system in place in your home, and when used as directed. Your heater is

designed to give your main heat source a supplement “boost,” or allow for you to have extra heat (in

the form of soft infrared waves) in locations where you would otherwise be short. It is meant to cycle

on and off, and not specifically designed to be used as a single heat source, especially in larger

homes. If you intend on using it as a single heat source (which you may), expect the heater to 1) take

as much as 24 hours to heat the area, 2) stay on for longer periods of time (without cycling off) due to

heat loss, and 3) increased use time, and electric costs.

My heater’s display shows my ambient temperature to be in the 2 ’s, when I know it is warmer

than that. Why?

The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is definitely

heating, but shows it is in the 20’s, you probably have the setting to read your temperature in Celsius,

rather than Fahrenheit. See Users Guide to change.

My heater comes with an ECO Mode. What is ECO Mode and what are the benefits?

The ECO mode on your heater is a program that regulates heat output to maintain the ambient

temperature strictly to a “warm” 68°F. The temperature cannot be changed or manipulated with the

remote or control panel, once it is in this mode. The ECO mode is considered an economical

function, as it is programmed to: 1) Utilize 1500W if the ambient temperature drops below 64°F 2)

Gradually decrease the wattage being used (to 750W) as it approaches 67°F and 3) Stop heating

when 68°F is achieved. This helps with power efficiency, since in the ECO setting (and if used as

supplemental heat), the heater is seldom running at the full 1500 Watts.

Is there anything else about ECO mode that I should know that may be helpful?

Yes. There are 3 specific things that need to be noted: 1) If the heater is set to ECO mode, and the

ambient temperature is already above 68°F, the heater will not activate. This is normal programming.

2) ECO mode is a feature meant to be used in rooms mainly where mild supplemental warmth is

warranted. 3) Keep in mind that if the room being heated or the outside environmental temperature is

very cold, the heater may stay on longer to warm up the room. If this “warm” heat does not meet your

intended heating purpose, the heater seems to be on for far too long, or you fear this mode may

increase your electric bills, we recommend you set the heater to either the “High” or “Low” mode. You

may also set the heater’s timer to have it shut off at specified hourly increments. See “On/Off Timer”

section of the User’s Guide.

HEATER OPERATION

Here is a small description of how our heaters work:

Operation Mechanism:

1) Air is brought into the heater through an easy to clean, washable filter at the rear of the

unit.

2) The highly efficient, one-speed, high volume fan pushes filtered air through the chamber,

across the heat elements.

3) During this exchange, heat is accumulated and transferred to the air in the chamber.

4) The newly transferred filtered, clean, and hot air is then circulated out the infrared heater’s

front vent.

5) The whole process produces variably hot air, compared to the air originally entering the

heater.

6) This method of heat generation creates an even, comfortable level of infrared heat from

floor to ceiling (as opposed to venting hot air blowing that will just rise to the ceiling and

dissipate)

7) There is no drying of the air with this method of heating and no harmful chemicals or

pollutants are released.

HEATER PLACEMENT

By using this infrared heater you can efficiently heat up to 1500 of unobstructed square feet. This

heater is NOT intended to replace your home’s furnace. Rather, it is designed to be a supplement

to it. It is not an instant heater, and on occasions (depending on various factors), can take up to

24 hours for a room to reach the desired temperature. Your Infrared Heater is equipped with a

lifetime washable static filter system which removes airborne contaminates as air circulates into

the heating chamber.

To achieve maximum efficiency of your Infrared Heater, please follow these recommendations:

Place your Infrared Heater at least 3 feet from an “inside” wall (a wall that is away from the

cold, outside perimeter of your house) of the room in which it will be used. Face the heater’s

exhaust vent (the grill) toward the cooler “outside” walls of the room. This positioning will allow

the heat to be moved across the room toward the outside walls to provide more even warmth

throughout the room.

Make sure that windows and doors are not allowing a high rate of airflow into the room where

you will be placing your heater. High airflow will minimize the effectiveness of your Infrared

heater, as it would any conventional type heater.

For best results, always try to maintain a minimum of 40% relative humidity in the environment

to be heated.

It is recommended that the Infrared heater be used in rooms that are insulated according to

code. You can use your heater in a room whether insulated or not, but a non-insulated room

will cause greater and faster heat loss which is counterproductive, and will keep the heater in

the “on” cycle longer. This may increase your electricity costs.

Keep the area around the heater clear of clutter and obstacles so that there is free airflow to

and from the heater.

Make sure to keep your heater out of the main traffic area of the room in which it is located; it

should be a welcome addition to the room rather than an obstacle to be stepped over or

stepped around.

The heater will pull a good amount of power (between 10-14 amps on average) from the wall

outlet and from the circuit (the circuit is considered all the outlets and lighting that is controlled

by a single house breaker). The heater needs to be connected to an individual circuit with

nothing else connected to that circuit. Doing so will exceed the maximum amperage

allowed for that breaker. Excessive heat, hot power cords, damage to outlets, and risk of fire

will be the result, if not adhered to, and will void your warranty (releasing Lifesmart from any

liability).

Table of contents

Other Life Smart Heater manuals

Life Smart

Life Smart LS1001HH13 Quick start guide

Life Smart

Life Smart HT1193 User manual

Life Smart

Life Smart LS-1000X-4M User manual

Life Smart

Life Smart INFRARED HEATER Quick start guide

Life Smart

Life Smart LS-EF450 Quick start guide

Life Smart

Life Smart LS-8WQH-DLX13B User manual

Life Smart

Life Smart LS-PP1500-6NAT User manual

Life Smart

Life Smart LS-1000X-4W User manual

Life Smart

Life Smart LS1006HH13 Quick start guide

Life Smart

Life Smart HT1289 User manual

Life Smart

Life Smart LS-3W-BPIQT User manual

Life Smart

Life Smart HT280 User manual

Life Smart

Life Smart HT1216 User manual

Life Smart

Life Smart R-LS-IRTWR-1 User manual

Life Smart

Life Smart Ultra LS1500-4WC User manual

Life Smart

Life Smart REFURBISHED R-W-19 User manual

Life Smart

Life Smart S-LPHW-3 Guide

Life Smart

Life Smart YAA02E-5 Quick start guide

Life Smart

Life Smart MCHT1153US User manual

Life Smart

Life Smart SH37 User manual

Life Smart

Life Smart R-HT1156 User manual

Life Smart

Life Smart LS-8WIQH-LB User manual

Life Smart

Life Smart LS1000HH13 Quick start guide

Life Smart

Life Smart LS-1500X-6WB Quick start guide

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide