Life Smart LS-PH08H Operator's manual



READ INSTRUCTIONS CAREFULLY:

Read and follow all instructions. Place instructions in a

safe place for future reference. Do not allow anyone who has not read these instructions

assemble, plug in, turn on, or operate the heater.

c

W

l

P

l

H

r



Model:LS‐PH08H



PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of

fire, electric shock, and injury to persons, including the following:



1. Read all instructions before using this heater.

2. Extreme caution: This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety. Children

should be supervised to ensure that they do not play with the appliance.

3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible

materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front

of the heater and keep them away from the sides and rear.

4. Always unplug heater when not in use.

5. Do not operate the heater with a damaged cord or plug or after the heater malfunctions, has been dropped or

damaged in any manner. Return it to authorized service facility for examination, electrical or mechanical

adjustment, or repair.

6. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never place the

heater where it may fall into bathtub or other water receptacles.

7. Do not run cord under material. Do not cover cord with throw rugs, runners, or similar coverings.

8. To prevent a possible fire, do not block the space between the heater and the wall which is for air intake or

exhaust in any manner.

9. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or

flammable liquids are used or stored.

10. Use this heater only as described in this manual. Any other use not recommended by the manufacturer

may cause fire, electric shock, or injury to persons.

11. If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or qualified

persons in order to avoid a hazard.

12. The heater must not be mounted over or directly above or below a power outlet.

13. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire.

14. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances

working. Do not install the heater under the wall socket.

15. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle)

and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or

worn outlet.

16. The output of this heater may vary and its temperature may become intense enough to burn exposed skin.

Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to

avoid burns.

17. WARNING: In order to avoid overheating, do not cover the heater.

18.SAVE THESE INSTRUCTIONS

Included In the Box

Items Required For Mounting

Gettin

Started

1. Unpack your heater and any packing materials

2. If all items are enclosed, thoroughly Inspect the heater for any shipping damage (cracks, dents, broken

power buttons, etc.) prior to doing anything else. If it was damaged in transit, contact your place of

purchase immediately.

1. Main Components:

·(Qty 1) Panel Heater

·(Qty 1) Instruction Manual

2. Mounting Hardware Pack Consisting of :

·(Qty 4) Plastic Mounting Posts w/ Built-In Wall Achor

·(Qty 1) Drill Bit

·(Qty 4) Long Mounting Screws

·(Qty 4) Plastic Screw Head Caps

2 People (to help hold it) · Mounting Hardware Pack · Power Drill · Medium Phillips Screwdriver · Small

Level · Pencil for marking the wall (if you think you may have to erase) or a Fine Tip Marker · Medium

Strength Glue (recommended but not essential)

Precautions Prior to Mounting

Mounting Instructions (Reference Fig 1-8 Next Page)

・2 People will be required to complete the mounting process.

・Keep all packaging and packaging materials until you have inspected the heater and all the contents of

the mounting hardware.

・The mounting hardware pack contains small items that should be kept away from young children.

・Do not plug in or power up the heater until it is secure to the wall and the instructions are read fully.

・Please choose a mounting location wisely, prior to starting. A power outlet must be within the

cord’s reach, but the heater must not be mounted over or within 12 inches above or below the

outlet.

・Please observe the recommended heights and dimensions for mounting the heater.

・This appliance is designed to be mounted to a wall at a minimum height of 8 inches from the floor.

・Take necessary precautions to avoid cutting or damaging any cables or power cords.

・While drilling holes for the mounting posts, be cautious of electrical lines, metals, or items beyond the

walls.

・Be sure that the wall you choose to mount on is solid, and will support the heater’s weight of

approximately 13 lbs.

・Make sure that the heater is safely out of the way while you are installing mounting hardware, as it

may become a tripping hazard if left in the open.

・Please be cautious if you are set on mounting the heater low to the floor, as it may become a

safety hazard to children and pets!

**Note: If you do not have a second person to assist, you may use the dimensions on Fig. 7 as a guide to

mounting without awkward handling of the heater.

1. Choose your mounting location based on the criteria in “Precautions Prior to Mounting.”

2. Make sure when choosing your mounting location, that the distance between the bottom of the heater

and the floor will be no less than 8 inches when the heater is installed

3. Once the mounting location is carefully picked out, and with assistance of a second person, lift the

heater, (with the flat side up against the wall) and straighten it using the small level.

4. Mark the positions of the four holes to be drilled on the wall with the pencil or marker (Ref. Fig 1).

5. At this point, lower the heater and place it where it will not be a tripping hazard.

6. Using the power drill, and the bit included in your mounting hardware kit, drill the marked holes on

the wall (Ref. Fig 2).

7. Insert the 4 plastic mounting posts into the holes. You should be able to press them in. If too difficult

to press, you may be able to lightly tap them in, using the screwdriver handle. (Ref. Fig 3)

8. Line up and slide the heater onto the 4 mounting posts the four holes in the heater (switch side towards

the wall). (Ref. Fig 4)

9. Once the heater is resting on the mounting posts, insert and tighten the screws onto the posts. (The

screwdriver is recommended to avoid stripping the posts or screw heads) (Ref. Fig 5)

10. Install the plastic end caps onto the heads of the screws. It is recommended to use a bit of medium

strength glue to hold each cap in place. (Extra strength glue or “crazy glue” is not recommended, in

case you need to remove in the future) (Ref. Fig 6).

11. Fig. 7 shows an outline of what the completed process should look like.

FIGS. 1-8

Fig 1 Fig 2

Fig3 Fig4

Fig5 Fig 6

Fig 7

Considerations For Maximum Heat Efficiency

Fig. 8

These are factors that you must consider to get the best use out of your heater:

・The intended room to be heated must be well insulated. Poor insulation will cause heat loss and

diminished heat efficiency.

・Mounting the heater near a flight of stairs will diminish efficiency, since the heat waves emitting from

the heater will constantly “fight” with cooler waves along the stairs.

・Open floor plans will be a factor, since heat is constantly being “lost” into other rooms, causing the

unit to be less efficient.

・Mounting the heater near open doorways, or doorways with excessive foot traffic will reduce

efficiency, since heat will constantly be lost through those doorways.

・Mounting the heater near/along open windows or windows that are constantly opened will cause heat

to escape and diminish full heat potential.

・Using this heater in a room larger than what the unit is intended for will diminish full heat potential.

ElectricalDiagram

To use the heater, please follow these instructions:

1. Plug in the heater.

2. Toggle the red on/off switch to the “on” position. The toggle switch should light up when powered

on.

3. Turn the toggle switch to the “off” position when you do not require heat.

4. Unplug the heater if you will be leaving it unattended for a while.

If your heater fails to operate, please follow these instructions:

Ensure that your circuit breaker or fuse is working properly.

Be sure the heater is plugged in and that the electrical outlet is working properly.

If the ON/OFF switch is not lit at ON position, contact technical support or consult with the place of

purchase immediately.

NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE WARRANTY INFORMATION FOR

INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE

WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE

CONTACT THE DISTRIBUTOR.

Before cleaning your heater, switch off the heater and allow it to cool. Disconnect the power cord from the

outlet. The outside of the heater can be cleaned by wiping it with a soft damp cloth and then dried. Do not

use abrasive cleaning powders or furniture polish, as this can damage the surface/ finish. To release the

heater from the wall, for cleaning or redecorating, just remove the plastic screw head cap and unscrew the

screws. Then just slide the heater off the wall.

For short term storage, just unplug the heater and safely coil up the power cord. For long term storage, you

can dismount from the wall and store, or just cover it on the wall with a cloth material.

Factory Model No.: PH-08H2

Voltage/Frequency: AC120V, 50/ 60Hz

(Please refer to the package information and be sure that your input voltage is matching with the rated input

voltage)

Tolerances on all specifications: Approximately +5%, -10%.

Recommended suitable Room Sizes:

Places with normal winter: 40 X 40 foot room

Places with cold winter: 30 X 30 foot room

This marking indicates that this product should not be disposed with other

household wastes throughout the EU. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, recycle it

responsibly to promote the sustainable reuse of material resources. To return

your used device, please use the return and collection systems or contact the

retailer where the product was purchased. They can take this product for

environmental safe recycling.



Limited Manufacturer Warranty

90 Day Limited Warranty

LIFESMART warrants this heater against defects in materials and workmanship on functional parts, for

a period of 90 days from the original date of purchase. Your sales receipt showing the date of purchase of

the product is your proof of purchase. Keep it in a safe place for future reference.

Manufacturer Warranty

AllLIFESMART products are manufactured with the highest quality materials and are warranted to be

free from defects in material and workmanship at the time of purchase. This limited warranty applies to

products manufactured or distributed by the LIFESMART brand name, are delivered in the continental

United States, and extends to the original purchaser, or gift recipient. This warranty becomes valid at the

time of purchase and terminates either by the specified time frame listed above and/or owner transfer

(unless otherwise authorized by LIFESMART, as the manufacturer). Any extended warranties (warranties

that cover above and beyond this manufacturer warranty) that are sold through a retailer or third party, are

not directly correlated with this LIFESMART limited warranty, and may be redirected to said retailer or

third party for coverage.

Extent of Warranty

This warranty extends through the manufacturer of the product, and covers functional parts only.

Cosmetics are not covered, unless unequivocally determined it is a manufacturer/workmanship defect. Note

that surface cracks are not considered defects in material or workmanship, as they are normal characteristics

of all wood and some plastics. Unless LIFESMART was the direct shipper, shipping damage should be

addressed with the shipping company, retailer, or place of purchase, prior to making a claim to

LIFESMART, as the manufacturer.

The manufacturer's sole obligation under this warranty shall be limited to furnishing the original purchaser

replacement parts for units deemed repairable by the LIFESMART warranty department. The purchaser

may also opt to ship the product to LIFESMART to have it repaired. The purchaser will be responsible to

prepay any shipping charges (both ways), export taxes, custom duties and taxes, or any other charges

associated with the transportation of the unit. In addition, the purchaser is responsible for insuring any parts

shipped or returned, if desired. For products the warranty department deems un-repairable, or discontinued,

LIFESMART reserves the right to issue a refurbished product, or product similar in size and functionality

as a replacement for the defective unit, if available. All exchanged parts and products replaced under this

warranty will become the property of LIFESMART.LIFESMART reserves the right to change

manufacturers of replacement parts or products for use, in order to cover any existing warranty. Any parts

determined defective may asked to be returned to LIFESMART or its representatives to validate a claim.

Non-Warranty replacement parts will be warranted 30 days from the time the purchaser receives them.

The purchaser must present LIFESMART with proof of purchase documents (including the date of

purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase documents will

be just cause to VOID this limited warranty. Products, in which the serial number has been defaced or

removed, are not eligible for warranty coverage. Continued…

Warranty Limitations

This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or

repairs (unless authorized verbally, or in writing, by an Authorized LIFESMART Representative) alteration

by non LIFESMART authorized personnel, inappropriate installations, or any case beyond the control of

LIFESMART. Examples of warranty invalidation may also include, but are not limited to:

Use of lacquer or paints in (and around)

the heaters

Heater placed on non-approved surfaces

Electrical requirement deficiencies

(15-20 amp dedicated outlet)

Use on Extension Cords/Timers/Surge

Protectors/GFCI

Outdoor applications

Normal wear/tear/weathering

Pet/Consumer accidents

Purchases from dealers unauthorized by

LIFESMART (Authorization in writing)

Disclaimers

LIFESMART shall not be liable for any loss due to use (or misuse) of the heater or other LIFESMART

products or other incidental or consequential costs, expense or damages without irrefutable foundations.

Under no circumstances shall LIFESMART or any of its representatives be held liable for injury to any

person or damage to any property, however arising. Any implied warranty shall have duration equal of the

applicable warranty stated above. Specifications are subject to change without notice or obligation.

Legal Remedies

This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state

to state.

Table of contents

Other Life Smart Heater manuals

Life Smart

Life Smart XXHT1141US User manual

Life Smart

Life Smart LS-Stealth-6FP User manual

Life Smart

Life Smart HT280 User manual

Life Smart

Life Smart MCHT1153US User manual

Life Smart

Life Smart HT1041 User manual

Life Smart

Life Smart LS?Stealth?4 User manual

Life Smart

Life Smart LS-1000X-6W User manual

Life Smart

Life Smart LS-PP1500-6NAT User manual

Life Smart

Life Smart HT1289 User manual

Life Smart

Life Smart HT1167 User manual

Life Smart

Life Smart R-LS-IRTWR-1 User manual

Life Smart

Life Smart INFRARED HEATER Quick start guide

Life Smart

Life Smart YAA02E-5 Quick start guide

Life Smart

Life Smart LS-1500X-6WB Quick start guide

Life Smart

Life Smart LCHT0016US User manual

Life Smart

Life Smart LS-6BPIQH-X Quick start guide

Life Smart

Life Smart LS-8WQH-DLX13B User manual

Life Smart

Life Smart PCHT1109US User manual

Life Smart

Life Smart LS1000-2 User manual

Life Smart

Life Smart HT1216 User manual

Life Smart

Life Smart LS-3ECO User manual

Life Smart

Life Smart S-LPHW-3 Guide

Life Smart

Life Smart HT1193 User manual

Life Smart

Life Smart R-HT1156 User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide