Kohler K-45205 User manual
Installation Guide
Shower Column
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-45205, K-45206, K-45207, K-45208
1176876-2-C
Tools and Materials
Before You Begin
NOTE: This guide includes the installation sequence for the shower
column only. Install the mixing valve, mixing valve trim, and spout
according to the manufacturer’s instructions.
NOTICE: Risk of product damage. Do not apply excessive weight
or downward force to the shower column.
CAUTION: Risk of property damage. Water leakage may
occur if supply piping allows movement. Ensure the supply
piping and 1/2″-14 NPT elbow fitting are securely fastened to
braces in the stud framing.
Please read all instructions before you begin.
Observe all local plumbing and building codes.
Shut off the water supply.
Inspect the existing supply piping and wall materials. Replace if
necessary.
The shower column is supplied with toggle anchor fasteners for
installation onto a finished wall surface. The finished wall
thickness must be a minimum of 5/8″(16 mm) and must be
adequate in strength. Two toggle anchor fasteners are required
per mounting collar.
IMPORTANT! If the supplied toggle anchor fasteners are not used
to install the shower column:
Sealant Tape
3/8"
100% Silicone Sealant
1/2"
Phillips
Screwdriver
1176876-2-C 2 Kohler Co.
Before You Begin (cont.)
Ensure that adequate strength wall backing materials and stud
bracing are properly positioned behind the finished wall.
Obtain proper fasteners (not provided) taking into account the
type of stud bracing material and thickness of the mounting
collar, finished wall, wall backing, and stud bracing.
Fasteners must be corrosion-resistant and capable of 300 lbs (136
kg) load bearing per fastener.
A minimum of two fasteners are required per mounting collar.
Fasteners must be securely anchored into the stud bracing to
adequately support the product.
IMPORTANT! For retrofit/remodel installations: Check the existing
shower enclosure for adequate clearances before proceeding with the
shower column installation. Refer to the Roughing-in for the shower
column and Rain showerhead.
Verify the distances between:
•The ceiling and the center of the existing shower arm at the
finished wall surface.
•The shower floor and the center of the existing shower arm at the
finished wall surface. Ensure sufficient clearance under the Rain
showerhead.
•The center of the existing shower arm and the center of the
mixing valve trim.
Kohler Co. 3 1176876-2-C
Roughing-In - Upper Supply Connection
Measure the distance between the 1/2″-14 NPT elbow and the
finished wall surface. The distance must be between 1-3/8″(35
mm) and 2-7/8″(73 mm).
IMPORTANT! The shower column connection will not seal
properly if the distance exceeds 2-7/8″(73 mm); see below for the
required deep roughing-in kit.
If the distance is between 2-7/8″(73 mm) and 4″(102 mm):
Order the 1194630 Deep Roughing-in Kit.
If the distance is less than 1-3/8″(35 mm): Order the 1187917
Shallow Roughing-in Kit.
Finished Wall Surface
1-3/4" (44 mm)
Minimum
Escutcheon
Clearance
1-3/8" (35 mm) –
2-7/8" (73 mm)
1/2"-14 NPT Elbow
1" (25 mm) Maximum
Wall Surface Offset
1176876-2-C 4 Kohler Co.
K-45205/K-45206 Roughing-In
Backing
Material
3-3/4"
(95 mm)
27"
(686 mm)
21-15/16" (557 mm)
K-45206
21-15/16" (557 mm)
9-1/2"
(241 mm)
K-45205
75" (1905 mm)
Recommended
72" (1829 mm)
Minimum
80" (2032 mm)
Recommended
75" (1905 mm)
Minimum Backing
Material
6" (152 mm)
Minimum
27"
(686 mm)
6" (152 mm)
Minimum
Kohler Co. 5 1176876-2-C
K-45207/K-45208 Roughing-In
18"
(457 mm)
21-15/16" (557 mm)
Backing
Material
Backing
Material
18"
(457 mm)
9-1/2"
(241 mm)
21-15/16" (557 mm)
75" (1905 mm)
Recommended
72" (1829 mm)
Minimum
3-3/4"
(95 mm)
K-45207
K-45208
78" (1981 mm)
Recommended
75" (1905 mm)
Minimum
6" (152 mm)
Minimum
6" (152 mm)
Minimum
1176876-2-C 6 Kohler Co.
1. Retrofit/Remodel Installation
CAUTION: Risk of property damage. Water leakage may
occur if supply piping allows movement. Ensure the supply
piping and 1/2″-14 NPT elbow fitting are securely fastened to
braces in the stud framing.
IMPORTANT! Check the existing shower enclosure for adequate
clearances as described in section ″Before You Begin.″
Remove the existing showerhead and shower arm escutcheon.
Carefully push the existing shower arm toward the finished wall
surface.
Check for inward movement of the supply piping.
If inward movement is possible, securely fasten the supply piping
to braces in the stud framing before beginning the shower column
installation.
Remove the existing shower arm.
Measure the existing shower arm hole. Ensure that the finished
wall material has an upper supply connection hole diameter
between 1″(25 mm) minimum and 1-1/4″(32 mm) maximum,
and the hole is centered on the outlet of the 1/2″-14 NPT elbow
fitting. Repair the wall surfaces if the existing shower arm hole is
not centered or exceeds the recommended dimensions.
Supply Piping
1/2"-14 NPT Elbow
Kohler Co. 7 1176876-2-C
2. Install the Supply Adapter
For New Construction Installations
CAUTION: Risk of property damage. Water leakage may
occur if supply piping allows movement. Ensure the supply
piping and 1/2″-14 NPT elbow fitting are securely fastened to
braces in the stud framing.
IMPORTANT! This guide includes the installation sequence for the
shower column only. Refer to the manufacturer’s instructions for
installation of the mixing valve, mixing valve trim, and spout.
Rough-in the mixing valve, supply piping, and bath spout
connection appropriate for your installation.
Refer to the ″Roughing-in″section in this guide for proper
location of the 1/2″-14 NPT elbow fitting inside the wall.
Ensure that the supply piping and 1/2″-14 NPT elbow fitting are
securely fastened to the stud framing.
3/8" Hex
Wrench
Supply
Adapter
1" (25 mm)
Minimum –
1-1/4" (32 mm)
Maximum
1/2"-14 NPT Elbow
1/2"-14 NPT Elbow
Supply Piping
1176876-2-C 8 Kohler Co.
Install the Supply Adapter (cont.)
Ensure that the finished wall material has an upper supply
connection hole diameter between 1″(25 mm) minimum and
1-1/4″(32 mm) maximum, and the hole is centered on the outlet
of the 1/2″-14 NPT elbow fitting.
If your supply connection hole diameter is between 1-1/4″(32
mm) and 2-1/4″(57 mm): Order the 1194302 Large
Escutcheon/Mounting Collar Kit.
Install the finished wall material.
Install the mixing valve trim and bath spout according to the
manufacturer’s instructions.
For New Construction and Retrofit Installations
Apply sealant tape to the supply adapter thread.
The supply adapter has an internal 3/8″hex socket. Thread the
supply adapter into the 1/2″-14 NPT elbow using a 3/8″hex
wrench.
Kohler Co. 9 1176876-2-C
3. Mark the Mounting Hole Locations
NOTE: The upper mounting collar must be centered on the supply
adapter. The distance between the upper and lower mounting collar
centers should be 18″(457 mm) or 27″(686 mm) depending on the
length of your shower column.
Center the mounting collar on the supply adapter. Mark the left
and right mounting holes.
For K-45205/K-45206 only: From the center of the supply adapter,
measure down 27″(686 mm) and mark the horizontal
measurement with a pencil.
For K-45207/K-45208 only: From the center of the supply adapter,
measure down 18″(457 mm) and mark the horizontal
measurement with a pencil.
Center the mounting collar on the horizontal line. Measure and
mark the left and right mounting holes. Ensure the upper and
lower mounting hole locations are level and plumb to one
another.
Do not drill the mounting holes until instructed to do so.
2" (51 mm)
Supply Adapter
K-45205/K-45206
27" (686 mm)
K-45207/K-45208
18" (457 mm)
Mounting Collar
Mounting Collar
1176876-2-C 10 Kohler Co.
This manual suits for next models
6
Table of contents
Languages:
Other Kohler Bathroom Fixture manuals
Kohler
Kohler Mira Showers Escape Thermostatic 9.8 kW User manual
Kohler
Kohler Sterling SC2522SBG Assembly instructions
Kohler
Kohler K-16281 User manual
Kohler
Kohler C3-255 Assembly instructions
Kohler
Kohler Fluence K-702400-L User manual
Kohler
Kohler K-9069 Assembly instructions
Kohler
Kohler Mira Advance 8.7 User manual
Kohler
Kohler Escale K-7219 User manual
Kohler
Kohler STANCE K-706527T-L-SHP User manual
Kohler
Kohler K-4615 User manual
Kohler
Kohler K-7600 Assembly instructions
Kohler
Kohler Mira Showers Decor 8.5 kW User manual
Kohler
Kohler Stillness K-960-4 Assembly instructions
Kohler
Kohler Chesapeake K-1728 User manual
Kohler
Kohler ODEON K-8827T User manual
Kohler
Kohler K-706139 Assembly instructions
Kohler
Kohler Sterling Solitaire SP2375-38 User guide
Kohler
Kohler K-1234 User manual
Kohler
Kohler K-14027 User manual
Kohler
Kohler K-17151X Assembly instructions
