Kogan KAMN24QUCMA User manual

USB-C QHD FREESYNC 75Hz

MONITOR (2560 x 1440)

KAMN24QUCMA

•Read all instructions before using the appliance and retain for reference.

•Unplug the monitor before cleaning it.

•Use a clean, slightly-dampened cloth to wipe the main monitor body.

•To clean the screen: turn it off, unplug it and wait for it to cool completely, then

wipe it with a dry microfibre cloth.

•Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.

•This monitor is designed with ventilation holes on the back of the casing. Do not

cover or block them.

•Do not insert any object or spray any liquid into the vents.

•Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat,

as well as in rooms lacking adequate ventilation.

•Do not position the monitor in unsafe locations. If the monitor falls, it may be

damaged and may injure nearby people.

•Unplug the monitor if it is not going to be used for an extended period.

•Do not place heavy objects on the monitor, its power cord or any connected cable.

•Do not open the back panel of the monitor, as it contains a high-voltage current

even when not plugged in.

SAFETY & WARNINGS

LED monitor

Stand Base Quick Start Guide

HDMI cable Power Cable Adapter

COMPONENTS

Controls

1. Menu/Enter

2. Volume/Down

3. Brightness/Up

4. Input select/Exit

5. Power On/Off

6. LED indicator

Ports

1. HDMI

2. DisplayPort

3. USB-C

4. USB1

5. USB2

6. EARPHONE

7. Power input (DC 24V)

OVERVIEW

Installing the Stand Base

1. Clear a table and place a piece of soft cloth on it to prevent the LED monitor from

being scratched.

2. Lay the LED monitor flat on the table with the LED screen facing down.

3. Insert stand into the monitor, then secure the base by turning clockwise as below.

4. Stand the LED monitor up.

Disconnecting the Stand Base

1. Clear a table and place a piece of soft cloth on it to prevent the LED monitor from

being scratched.

2. Lay the LED monitor flat on the table with the LED screen facing down.

3. Press the release button and pull away the monitor to remove the stand from the

monitor.

4. Pull the release lever and turn anticlockwise to remove the base from stand. Press

the release button.

STAND ASSEMBLY

Follow the steps below to install onto a monitor arm or wall mount (not included)

1. Place the mounting plate onto the back of the LED monitor, lining up the holes of

the plate with the holes in the back of the monitor.

2. Insert the 4 screws into the holes and tighten.

3. Assemble the mount as per the instructions provided with the mount.

4. Connect the power and display cables to the monitor.

VESA MOUNT

Note:

100 x 100mm VESA high hole (n=4), M4, pitch=0.7mm, screw mounting kit

not included.

100mm

100mm

Before using the LED monitor

•Connect external equipment properly.

•Insert the power plug: the power LED indicator will glow orange,without signal

input.

Setup

1. Connect the HDMI, DP or USB Type-C cable from your monitor to the computer.

2. Connect the adapter to a properly grounded AC outlet, then to the monitor.

3. Power ON the computer and then power ON the monitor.

4. Set the timing mode on your computer. Recommended resolution and refresh rate

are 2560x1440 @75Hz.

OPERATION

USB-C Connection

This monitor supports the following simultaneous connections via USB Type-C:

•Display via DisplayPort™ 1.2 alternate mode

•Data via USB 3.1

•Power delivery (20V/3.25A, 15V/3A, 9V/3A, 5V/3A)

NOTE: Type-C is not supported on versions of Windows prior to Windows 10.

USB-C Setup

1. Connect the USB Type-C cable from your monitor to the computer.

2. Connect the adapter to a properly grounded AC outlet, then to the monitor.

3. Power ON the computer and then power ON the monitor.

4. Set the timing mode on your computer. Recommended resolution and refresh rate

are 2560 x 1440 @60Hz.

Power ON/OFF

•Press the power button on the front of the monitor: the power LED indicator light

will be blue when the LED monitor is on.

Using the OSD menu

•Use OSD menus to adjust settings by using the menu button on the front of the

LED monitor.

Displays main menu

Enter OSD menu

Selects between HDMI, DP and USB-C. Exit OSD menu

Select the desired item when in OSD menu

When not in the OSD menu, directly enters Volume Menu

Select the desired item when in OSD menu

When not in the OSD menu, directly enters Brightness Menu

Table of contents

Other Kogan Monitor manuals

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Furuno

Furuno Mu 120c Operator's manual

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual