Knightsbridge BLED5BW Instruction Manual

INSTALLATION & MAINTENANCE MANUAL

BLED5BW / BLED5BB

BLED5SW / BLED5SB

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following products:

BLED5BB / BLED5BW / BLED5SB / BLED5SW

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed the rating of the

circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation

• This product is Class I and must be earthed

• This product is IP54 rated

SAFETY

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please conﬁrm with the

manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP

rated junction boxes should be used where required

• Round cable should be used for the mains supply. The use of ﬂat cable will cause water ingress to the ﬁtting

• Remove the front bezel by unscrewing the two side screws

• Remove the PCB from the back plate by unscrewing the two diagonal screws

INSTALLATION

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

This product is not suitable for direct installation in the ground, nor in a retaining wall where the ground may

become saturated behind.

This product is not suitable for installation in or near a coastal or marine environment.

WARNING

• Using the back plate as a template, mark the location for, and drill the ﬁxing holes ensuring not to infringe

with any gas/water pipes or electrical cables

• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the

surface

• Fix the base to a suitable solid surface using the screws provided. Rubber washers or sealant should be

applied around the screw heads to prevent water ingress

• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown),

E - Earth (green/yellow), N - Neutral (blue)

• Reattach the PCB and front bezel

• Switch on and check for correct operation

This product contains a light source of energy efﬁciency class F (BLED5BW, BLED5SW) to Regulation (EU)

No. 2019/2015.

This product contains a light source and control gear which can be replaced by a professional.

GENERAL

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

BLED5BB / BLED5BW / BLED5SB / BLED5SW

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse, or circuit breaker

•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for

installation

•This product is Class I and must be earthed

•This product is IP54 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires.

•Provide power to the required point of installation (refer to BS7671 for correct cabling methods).

Suitable IP rated junction boxes should be used where required

•Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the

fitting

•Remove the front bezel by unscrewing the two side screws

•Remove the PCB from the back plate by unscrewing the two diagonal screws

•Using the back plate as a template, mark the location for, and drill the fixing holes ensuring not to

infringe with any gas/water pipes or electrical cables

•Feed the mains cable through the rubber grommet to retain IP rating, and secure the base plate to the

surface

•Fix the base to a suitable solid surface using the screws provided. Rubber washers or sealant should

be applied around the screw heads to prevent water ingress

•Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown), E

- Earth (green/yellow), N - Neutral (blue)

•Reattach the PCB and front bezel

•Switch on and check for correct operation

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

This product is not suitable for direct installation in the ground, nor in a retaining wall where the ground may

become saturated behind.

This product is not suitable for installation in or near a coastal or marine environment.

GENERAL

This product contains a light source of energy efficiency class F to Regulation (EU) No. 2019/2015.

This product contains a light source and control gear which can be replaced by a professional.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not

use aggressive cleaning products or solvents which may damage the product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

This product is non-dimmable.

This product should be dismantled for disposal when it reaches the end of its life. Please see website for

dismantling instructions.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place

of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product speciﬁcation without prior notice.

WARRANTY

AVAUG 21_V2

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

-25~

35°C

This manual suits for next models

Table of contents

Other Knightsbridge Lighting Equipment manuals

Knightsbridge

Knightsbridge BT14CTEM Instruction Manual

Knightsbridge

Knightsbridge HBN Series Instruction Manual

Knightsbridge

Knightsbridge EMGUKIT1 Instruction Manual

Knightsbridge

Knightsbridge EMXST Instruction Manual

Knightsbridge

Knightsbridge LEDFIPCCT Instruction Manual

Knightsbridge

Knightsbridge WW15C Instruction Manual

Knightsbridge

Knightsbridge LFX512WW Instruction Manual

Knightsbridge

Knightsbridge SLULED Instruction Manual

Knightsbridge

Knightsbridge TRI Series Instruction Manual

Knightsbridge

Knightsbridge LWALL1A Instruction Manual

Knightsbridge

Knightsbridge EMPOWER2 Instruction Manual

Knightsbridge

Knightsbridge TNXQUADEMW Instruction Manual

Knightsbridge

Knightsbridge TNXQUADSTW Instruction Manual

Knightsbridge

Knightsbridge 12DC36 Instruction Manual

Knightsbridge

Knightsbridge KIT16 Instruction Manual

Knightsbridge

Knightsbridge LEDM06 Series Instruction Manual

Knightsbridge

Knightsbridge LEDBATW Series Instruction Manual

Knightsbridge

Knightsbridge BATC Series Instruction Manual

Knightsbridge

Knightsbridge BATC Series Instruction Manual

Knightsbridge

Knightsbridge GU10SPIKE Instruction Manual

Knightsbridge

Knightsbridge TRLED EM Series Instruction Manual

Knightsbridge

Knightsbridge TNXQUADMWEMW Instruction Manual

Knightsbridge

Knightsbridge 12DC40 Instruction Manual

Knightsbridge

Knightsbridge EMPOWERST Instruction Manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions