Kitsound SLAM 70 User manual

QA-MRK-FM-08-02 v1

REG05 – International – USA, EU, AUS

FRON COVER

KSSLA70

KitSound SLAM 70 Bluetooth Party Speaker

Owner’s Manual

INNER LEAF

Please read this manual carefully before use.

WARNING

•Please do not get the product wet. If your product is IP rated, please follow guidelines on

how to safely use your product overleaf.

•Please don’t take the product apart. here are no user serviceable parts inside

•Please don’t modify or alter the product or accessories

•Please don’t expose the product to extreme temperatures or rapid changes of hot to cold or

vice versa

•Please don’t use damaged cables or plugs, or loose electrical sockets

•Please don’t touch the device, cables, plugs, or the electrical socket with wet hands or other

wet body parts

•Please don’t pull the cable excessively when disconnecting it if the cable is not fixed

•Please don’t bend or damage the cable

•Please don’t drop or cause an impact to the product or the device

•Please don’t place naked flame sources, such as lighted candles, on the product

Battery Information

•Batteries may malfunction if they are not used for extended periods

•Over time, unused devices will discharge and must be recharged before use

•Disconnect the charger from power sources when not in use

•Use the batteries only for their intended purposes

•Follow all instructions in this manual to ensure the longest lifespan of your device and battery.

Damages or poor performance caused by failure to follow warnings and instructions can void

your manufacturer’s warranty

•Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as

sunshine, fire or the like

QA-MRK-FM-08-02 v1

•Please do not dispose of the battery in a fire or an oven, or mechanically crush or pierce the

battery, as this may result in an explosion.

•Please do not subject the battery to extremely low air pressure, which may result in an explosion

and/or the release of flammable liquid or gas

IP 67

he speaker is rated IP67. he 6 means that the Slam 70 is protected against dust and contact. No

ingress of dust permitted. he 7 means it protects from ingress of water when the enclosure is

immersed in water at a depth of 1m for up to 30 minutes.

• o ensure that the Slam 70 is water resistant, please remove all cable connections and tightly close

the AUX/DC IN cap; exposing the speaker to liquids without doing so may result in permanent

damage to the speaker.

• Do not expose the Slam 70 to water while charging; this is very dangerous as doing so may result in

personal injury and permanent damage to the speaker or power source.

• IP67 rating is defined as the Slam 70 can stand immersion of 1 metre for up to 30 minutes.

• We do not recommend leaving the Slam 70 outside at night time in wet conditions or when it’s

raining. Store in a dry place while not in use, this will prolong the speakers life.

QA-MRK-FM-08-02 v1

Quick tart Guide

1. Power On by pressing Power button for 2 seconds.

2. urn on your device’s Bluetooth and connect to ‘K lam 70’.

Change to ‘Press & hold for 2 seconds’ ^

Change up the Lighting and Boost the ound

1. Follow the Quick tart Guide instructions.

2. Use the buttons on the handle control panel to adjust lighting, add strobes and change up the

audio modes.

Chill Modes Party Mode Lighting / trobes Colour election 360 ound

Further information on connecting to the speaker, and instructions on how to use all of the product

features, can be found in the following pages of this manual.

QA-MRK-FM-08-02 v1

Box contents

•KS SLAM 70 Bluetooth Speaker

•User manual

•3.5 mm aux cable

•Micro USB charge cable

Functions

1. Power Button

2. Volume+/Next track

3. Volume–/Previous track

4. Pairing Button

5. Chill Mode Button

6. Party Mode Button

7. Lighting / Strobe Button

8. Colour Button

9. 360 Sound Button

10. Micro USB Charging Port

11. Aux-in Port

QA-MRK-FM-08-02 v1

Instructions for use

Getting started

Charging the battery:

Give the speaker a full charge before its first use:

1. Connect the supplied Micro USB charging cable to the Micro USB charging port (10) and plug into

power

2. he Power button (1) will be solid red whilst charging which will take up to 7 hours

3. Once fully charged the Power button (1) will turn white

Note:

•

Allow up to 7 hours for the first charge.

You can play your speaker whilst it is being charged,

but this will affect the charging time.

•Due to the large battery in the Slam 70 we recommend regularly charging the battery

whenever practical. his will also help to ensure the longevity of the battery’s life.

•he Slam 70 can be charged by a power bank (portable charger) via a micro USB cable.

herefore you may consider taking a power bank (portable charger) when planning on using

the Slam 70 for extended periods away from mains charge capability.

•When the battery is in power saving mode, the Slam 70 volume will be limited to 50%. Please

recharge the battery further if you wish to increase the volume.

LED lights indication

Pairing mode

Pairing button

(4)

will flash red every 1 second

Paired in Bluetooth® mode

Pairing button

(4)

will turn white

pairing

multiple

lam 70

speakers

Pairing button

(4)

will flash

red

twice

every second

Paired (master speaker)

Pairing button (4) will be solid

white

WS Paired (Slave speaker)

Pairing button (4) will be solid

white

Battery

low

Power button

(1)

will flash red every 10 seconds

Charging battery

Power

button

(1)

will be solid red

Charging complete (around 95%)

Power button

(1)

will be solid white

Indoor 360

Sound

360

Sound

button (9) will be solid red

Outdoor 360 Sound ON

360 Sound button (9) will flash red once every 3 seconds

Shelf Sound ON

360 Sound button

(9)

will be solid white

Party Mode lighting ON

Party Mode button (6) will be solid red

QA-MRK-FM-08-02 v1

Chill Mode lighting ON

Chill mode button (5) will be solid red

Pairing the lam 70 to your device

1. Press Power button (1) for 2 seconds to turn the speaker on and it will automatically enter

pairing mode

2. urn your iOS, Android, or Windows device’s Bluetooth ON and search for new devices

3. Select ‘KS Slam 70’. If asked for a passcode, enter ‘0000’, and the device will pair

4. Once connected the Pairing button (4) will turn white.

Re-pairing or pairing new devices

1. urn Bluetooth connectivity off on any previously paired devices

2. Press the Pairing button (4) to re-enter pairing mode

3. Follow the ‘Pairing the Slam 70 to your device’ instructions

Note: If a previously paired device is not present within the Bluetooth connectivity range then the

speaker will re-enter pairing mode.

TW pairing two K lam 70 speakers

1. Press Power button (1) to turn on both of the Slam 70 speakers that you wish to pair

together. Both speakers will automatically enter pairing mode.

2. Double press the Pairing Button (4) on either of the speakers and it will enter WS pairing.

he pairing button (4) will flash red on the master speaker.

Once connected in WS pairing both speakers will commence party lighting in sync.

4. Follow the ‘Pairing the KS Slam 70 to your device’ instructions to pair your device to either Slam

70.

5. Once connected the Pairing button (4) will turn white.

Disconnecting two K lam 70 speakers from TW

Double press the pairing button (4) on either of the paired speakers to disconnect them from WS

pairing.

Playing music on your speaker

Bluetooth

When connected via Bluetooth, play music on your device and the sound will play through the

speaker. Some devices may require you to select the audio output.

QA-MRK-FM-08-02 v1

Auxiliary

Plug the Aux cable into the speaker’s Aux-in Port (11) and your device using the supplied cable.

Auxiliary and TW pairing

1. Ensure both speakers are paired before you connect the aux cable to the master speaker.

Follow instructions for ‘ WS pairing two KS Slam 70 speakers’.

2. Connect the aux cable to the master speaker. he Master speaker can be identified as the

speaker with the Pairing button (4) flashing red.

3. Once connected, pairing button (4) will now be white on both speakers.

Once connected to the Slam 70 either wired or by Bluetooth, please follow the instructions on next

page:

Function

Bluetooth mode

Auxiliary mode

urn Off/On

Hold

Power button (1) for

seconds

Hold Power button (1) for

seconds

Volume+

Short press Volume +

button (2), or use your device

Short press Volume +

button (2), or use your device

Volume

–

Short press Volume

–

button (3), or use your device

Short press Volume

–

button (3), or use your device

Next rack

Hold down Volume +

button (2) for 3 seconds

N/A

Previous rack

Hold down Volume

–

button (3) for 3 seconds

N/A

Play/Pause rack

Short press Power button

(1)

Short press Power button

(1)

Pair with device

Short press Pairing button

(4)

N/A

Pair speakers with WS

Double press Pairing button (4)

on one of the units

Double press Pairing button (4)

on one of the units

Remove speaker from WS

Double press Pairing button (4)

on one of the units

Double press Pairing button (4)

on one of the units

Select

Chill Mode

Lighting

Short press Chill mode

button (5) to toggle between

the three Chill modes

Short press Chill mode

button (5) to toggle between

the three Chill modes

Select

Party Mode

Lighting

Short press Party mode

button (6)

Short press Party mode

button (6)

Strobe Lighting On/Off*

Short press Lighting button

(7)

Short press Lighting button

(7)

Increase Light Brig

htness

Hold down Lighting button

(7) and press Volume + button

(2)

Hold down Lighting button

(7) and press Volume + button

(2)

Decrease Light Brightness

Hold down Lighting button

(7) and press Volume - button

(3)

Hold down Lighting button

(7) and press Volume - button

(3)

Change Light Colour

Short press

Colour

utton

(8) to toggle between colours

Short press Colour

utton

(8) to toggle between colours

360

Sound

Modes

Short press

Sound

oost

button (9) to toggle between

Short press Sound Boost

button (9) to toggle between

QA-MRK-FM-08-02 v1

modes

Factory Reset

Hold down Power

button

(1) and Volume + button (2) for

10 seconds

Hold down Power

button

(1) and Volume + button (2) for

10 seconds

*Strobe lighting is only available in Party Mode.

** If you preform a factory reset we recommend turning the speaker off and back on again,

otherwise you may experience difficulties with WS pairing.

Light mode controls

he Slam 70 has four different light modes. hese include Chill mode 1, 2 and 3, as well as Party

mode. Within Party mode there is the additional option to add strobe lighting.

Light Mode

Button

Description

Chill Mode 1

Chill mode

button (5)

Multicolour ambient lighting with

various

colour wave transitions.

Chill Mode 2

Chill mode

button (5)

Single colour pulsing ambient lighting. he lighting colour can be

changed using the colour button (8).

Chill Mode 3

Chill mode

button (5)

Single colour ambient light. he lighting colour can be changed

using the colour button (8).

Party Mode

Party mode

button (6)

Multicolour party lighting that follows the beat of the music

and

with additional colour transitions.

Strobe Mode

Lighting

button (7)

Enter Party mode first then use

Lighting

button (7) to add strobe

lighting to the Party mode sequence.

*Strobe lighting is only available in Party Mode.

Light brightness controls

he brightness of the lighting can be adjusted using the lighting button.

1. Hold down the lighting button (7) and short press Volume + (2) to increase brightness

2. Hold down the lighting button (7) and short press Volume – (3) to decrease brightness.

Using the brightness controls above will allow you to adjust the light brightness manually.

QA-MRK-FM-08-02 v1

Light ynchronisation Reset

If strobe lighting appears to be unsynchronised then we recommend that you exit Party mode by

pressing the Chill mode button (5) and then re-entering Party Mode by pressing Party mode button

(6).

ound Modes

Slam 70 offers three different sound modes. hese include Indoor 360, Outdoor 360 and Shelf. Use

the 360 Sound button (9) to toggle between the three different modes.

ound Mode

Button

Colour

Description

Indoor 360

Solid Red

360 degree audio, tuned for listening indoors.

Outdoor 360

Flashing Red

360

degree audio, tuned for listening in outdoors.

Shelf

Solid White

Directional sound from the front of the speaker, perfect for

listening whilst the Slam 70 is against a wall or in the corner of a

room.

Battery Protection Mode

For all night long parties, we recommend connecting the speaker to power via the micro USB cable,

or taking a power bank with you. We recommend using a 2.1 amp power bank for charging your

Slam 70.

If you don’t own a power bank, please contact Kitsound. We will be able to recommend power banks

for purchase.

o keep the party going as long as possible, use the following guide to manage the battery playtime.

With

Lights ON

Volume Level

Regular Playtime

Battery Protection

Mode

Playtime

Charge time

to exit

the

Battery Protection mode

100%

4.5 hours

15 minutes

Up to 1 hour and 20 mins

70%

10.5 hours

25 minutes

Up to 1 hour

With

Lights OFF

Volume Level

Regular Playtime

Battery Protection

Mode

Playtime

Charge time to exit

the

Battery Protection mode

100%

hours

20 minutes

Up to 45 mins

70%

17 hours

35 minutes

Up to 35 mins

Please note:

QA-MRK-FM-08-02 v1

-Your Slam 70 will enter Battery Protection Mode when the battery is low in order to prolong

the playtime.

-Charge the Slam 70 before or as soon as it enters Battery Protection Mode in order to

prolong the battery life and to ensure that it is always chargeable.

-he volume in Battery Protection Mode will be limited to 50%.

-If your Slam 70 is out of battery it will take up to 1 hour and 20 minutes to charge up and

exit Battery Protection Mode, if you are playing music at 100% volume.

-Your Slam 70 will not fully charge if you are playing music at high volume and the lights are

on.

pecifications

Bluetooth® technology v

Bluetooth connectivity distance

up to 10 m

Bluetooth

Frequency

Band

2402

–

480M

ransmission power

(conducted)

S/N

Frequency response

–

0 kHz

Drivers

, 1 x 102mm

Output RMS

Battery

ion

18650

Play time

up to

hours

Charging time

up to

hours

ratings

Working temperature

°C ~ +

°C

Speaker size

(mm)

230mm

x W

175mm

Cable length

500

Weight

2.35

Troubleshooting

We hope you've now got all the information you need to get started, but if you're having problems

with anything, please feel free to contact us at: support@kitsound.co.uk

‘Hereby, Kondor Ltd declares that the radio equipment type,

KSSLA70

, is in compliance with

Directive 2014/53/EU. he full text of the EU declaration of conformity is available at the

following internet address: http://kondor.co.uk/product-documents.’

FCC ID: 2ADFF-K LA70

his device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Table of contents

Other Kitsound Speakers manuals

Kitsound

Kitsound POCKETBOOM User manual

Kitsound

Kitsound POCKETBOOM XB User manual

Kitsound

Kitsound SLAM User manual

Kitsound

Kitsound DIGGIT XL User manual

Kitsound

Kitsound RINSE User manual

Kitsound

Kitsound MIAMI User manual

Kitsound

Kitsound DANCEFLOOR User manual

Kitsound

Kitsound VOICE ONE User manual

Kitsound

Kitsound Glow Stereo User manual

Kitsound

Kitsound HIVE 2 User manual

Kitsound

Kitsound GLOW User manual

Kitsound

Kitsound CUBE User manual

Kitsound

Kitsound Hive 2 User manual

Kitsound

Kitsound FLAIR User manual

Kitsound

Kitsound KS DIGGIT User manual

Kitsound

Kitsound UPSTAGE User manual

Kitsound

Kitsound BOXI MINI User manual

Kitsound

Kitsound Hive Discovery User manual

Kitsound

Kitsound POCKET HIVE User manual

Kitsound

Kitsound Mini Buddy User manual

Kitsound

Kitsound IGNITE User manual

Kitsound

Kitsound Sonar User manual

Kitsound

Kitsound KS SLAM XL User manual

Kitsound

Kitsound OVATION User manual

Popular Speakers manuals by other brands

argon audio

argon audio IE20 quick start

Denon

Denon SC-N7 owner's manual

Gemline

Gemline Ace 3952 user manual

Focal

Focal ON WALL 300 User manua

HEADRUSH

HEADRUSH Maximus HRSP 5024 manual

SoundLogic

SoundLogic BCCS-6/6395 instruction manual

Peavey

Peavey DTH 218 Specification sheet

Avantree

Avantree Pluto Air user guide

Morel

Morel Integra Series INTEGRA OVATION 4 install guide

Oppo

Oppo SONICA quick start guide

Bose

Bose SoundLink Wireless Music System owner's guide

Rocksteady

Rocksteady Stadium owner's manual

Bowers & Wilkins

Bowers & Wilkins 4 owner's manual

Sonance

Sonance SONOS OUTDOOR Series installation manual

Electro-Voice

Electro-Voice EVID FM4.2 Brochure & specs

Pioneer

Pioneer XW-HTD630 manual

Onn

Onn BWA16AA002 Product guide

HP GL313AA - USB Speakers PC Multimedia quick start guide