Kichler Lighting Szeplo II User manual

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

Szeplo II

A Kichler

Decor

™

ceiling fan

Includes wall mount

control system

300300,300301,300302

3066708

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualiﬁed

licensed electrician.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting ﬁxtures are not acceptable for fan

support and may need to be replaced,

consult a qualiﬁed electrician if in doubt.

5. WARNING: To reduce the risk of ﬁre,

electric shock, or Personal Injury, mount

directly to a structural framing member or

to an outlet box marked 'Acceptable for

Fan Support of 15.9 kg (35 lbs) or less'. For

outlet box mounting, use mounting screws

provided with the outlet box.

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the ﬂoor.

7. To operate the reverse function on this fan, press

the reverse button while the fan is running. A few

seconds later the fan will slow to a stop and then

reverse direction.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the ground wire and white

(common) wire to one side with the black

(load) wire to the other side of the outlet

box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be ETL Listed and marked suitable

for use with the model fan you are

installing. Switches must be ETL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

1. SAFETY RULES

WARNING

To reduce the risk of ﬁre, electric shock, or

Personal Injury, mount directly to a structural

framing member or to an outlet box marked

'Acceptable for Fan Support of 15.9 kg(35 lbs)

or less'. For outlet box mounting, use mounting

screws provided with the outlet box.

3. WARNING: To reduce the risk of ﬁre or

electric shock, Use only the control

provided with the fan.

3. PACKAGE CONTENTS

Unpack your fan and check the contents .

You should have the following items:

A. Mounting bracket

B. Ball / downrod assembly

C. Canopy

D. Canopy Trim Ring

E. Coupling cover

F. Motor Body

G. Blade Arm (6)

H. Blade (6)

I . Switch Housing

J. Led Assembly

K. Glass Shade

L. Steel Cap

M. Power Kit

N. Package Hardware

1) Mounting hardware:

wood screws (2), ﬂat washers (2),

screws (2) , lock washers (2),

wire nuts (3)

2) Blade arm hardware :

screw (2)

3) Safety cable hardware :

wood screw (1) , spring washer (1),

ﬂat washer (1)

4) Balance kit

5) Blade Mounting hardware:

8# screws (20), washers (20)

screw (3)

6) Screw hardware:

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

Szeplo II

4. MOUNTING OPTIONS

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 30°ANGLE

If there isn't an existing ETL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling.

A minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin installation. This is necessary for your

safety and also the proper programming of the

control system.

To properly install your ceiling fan, follow the

steps below.

Step 1. Before attaching fan to outlet box

(not included), ensure the outlet box is securely

fastened to at least two points to a structural

ceiling member (a loose box will cause the fan

to wobble). Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. Install mounting

bracket to outlet box in ceiling using the screws

and washers included with the outlet box or

screws and washers in the hardware bag.

(Fig. 5)

Step 4. Slip the coupling cover, canopy trim ring

and canopy onto the downrod. Carefully reinstall

the hanger ball onto the downrod . Make sure the

cross pin is in the correct position and the set

screws are tight and the wires are not twisted .

( Fig. 8)

Step 2. Remove the hanger ball from downrod

assembly by loosening set screws , removing

the cross pin, and twisting ball out of the rod.

( Fig. 6)

Step 3. Loosen the two set screws and remove

the clip and cross pin from the top coupling of

the motor body.

Carefully feed the fan wires up through the

downrod. Thread the downrod onto the motor

coupling until the cross pin holes are aligned.

Next, replace the cross pin and clip, and tighten

both set screws. (Fig. 7)

Flat Washer

Screw

Fig. 5

Ceiling Mounting Bracket

ETL Listed Outlet Box

Screw

Downrod

Cross Pin

Fig. 6

Set Screw

Hanger Ball

Fig. 7

Fig. 8

Szeplo II

Motor Body

Cross Pin

Clip

Set Screw

Hanger Ball

Canopy

Canopy Trim Ring

Coupling Cover

Motor Body

Step 5. Now lift the motor body into position

and place the hanger ball into the hanger bracket.

Rotate until the "Check Tab" has dropped into

the "Registration Slot " and seats ﬁrmly. ( Fig. 9)

The entire motor body should not rotate is this is

done correctly.

6 . INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

WARNING: Failure to properly seat the "Check

Tab" can damage the ceiling fan during operation.

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Drive a wood screw and washers into the

side of the brace that holds the outlet box. Leave

3mm (1/8") of space between the support brace

and the washer. (Fig. 10)

NOTE: Although the safety support cable is

required for Canadian installations only. It’s a good

idea to make the attachment with any installation.

Step 2. Insert the safety cable through the

mounting bracket and one of the holes in the

outlet box into the ceiling. Adjust the length of the

safety cable to reach the screw and washers by

pulling the extra cable through the cable clamp

until the overall lenght is correct, put the end of the

cable back through the cabel clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of the

safety cabel over the wood screw and under the

washer. Tighten the wood screw securely. (Fig. 11)

Safety Cable Bolt

Wood Screw

Fig. 11

Fig. 10

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

Fig. 9

Hanger Ball

Check Tab Registration Slot

7. HOW TO WIRE YOUR CEILING FAN

8. INSTALLATION OF THE CANOPY

Step 1. Remove one of the two shoulder screws

in the mounting bracket. Loose the second

shoulder screw without fully removing it. (Fig. 14)

Step 2. Assembly canopy by rotating key slot in

canopy over shoulder screw in mounting bracket.

Tighten shoulder screw. Fully assembled and

tighten second shoulder screw that was previously

removed. (Fig. 15)

Fig. 14

Fig. 13

Fig. 12

Fig. 15

Mounting Bracket

Shoulder Screw

Green (ground) Wire

Black Wire

White Wire

Green Wires

Black Wire

White Wire

If you feel that you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electricial.

Warning: To avoid possible electrical shock, be

sure electricity is turned off at the main fuse box

before wiring.

Note: If you are not sure if the outlet box is

grounded, contact a license electricial for advice,

as it must be grounded for safe operation.

Step 1. Connect the GREEN grounding leads

to the grounding conductor of supply (this may

be a bare wire or wire with green colored insulation).

Securely connect wires with wire connector

supplied. (Fig. 12)

Step 2. Securely connect the fan WHITE wire to

the supply WHITE wire using wire connector

supplied. Securely connect the fan BLACK wire

to the supply BLACK wire using wire connector

supplied. (Fig. 12)

Step 3. After connections have been made, turn

leads upward and carefully push leads into the

outlet box, with the white and green leads on

one side of the outlet box and position

the black leads on the other side of the oulet box.

(Fig. 13)

Canopy

Shoulder Screw

Szeplo II

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. Position the blade over the blade arm

with threaded posts showing. Make sure the

bottom edge of the blade is fully seated against

the blade arm. With a Philips screwdrivr, start

a screw into the blade arm (do not tighten)

and repeat for the 2 remaining blade screws

and washers. Tighten each screw securely

starting with the center screw. Make sure the

blade is straight. Repeat steps for the

remaining blades. (Fig. 17)

Step 2. Remove and discard the three stabilizers

tabs and screws. Faster blade assembly to the

holes located on the bottom of the ﬂywheel.

Tighten the two "pre- installed" motor screws

in the blade arm. Repeat steps for the remaining

blades assemblies. (Fig. 18)

9. ATTACHING THE FAN BLADES

Fig. 17

Fig. 18

Step 3. Securely attach and tighten the canopy

trim ring over the shoulder screws in the mounting

bracket utilizing the keyslot twist-lock feature.

(Fig. 16)

Fig. 16

Canopy Trim Ring

Blade Screw

Blade

Blade Arm

Washer

Shipping Block

Screw

Blade Assembly

Blade Arm Screw

Motor Body

11. INSTALLING THE LED ASSEMBLY OR CAP

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. If installing with steel cap and no light

kit, skip to step 4 on page 9. Remove one of

the three screws in the switch housing.

Retain the screw for later and slightly

loosen the remaining two screws. (Fig. 20)

Step 2. Connect the 2 single pin connectors

from the LED assembly to the 2 single pin

connectors from motor assembly,

BLACK to BLACK, WHITE to WHITE.

Assemble the LED assembly to the switch

housing using the two key slots. Replace the

removed screw and secure all three screws.

(Fig. 21)

Fig. 20

Fig. 21

Step 1. Remove one of the three screws and

loosen the other two (do not remove). Place the

two slot holes on the switch housing over the 2

screws previously loosened from the mounting

ring. Rotate the switch housing until it locks in

place at the narrow end of the key holes.

Securely by tightening the 2 screws previously

loosened and the one previously removed.

(Fig. 19)

10. INSTALLING THE MOUNTING PLATE

Fig. 19

Switch Housing Screw

Mounting Plate

Switch Housing

Screw

LED Assembly Screw

Switch Housing

Szeplo II

Fig. 24

12. WALL CONTROL INSTALLATION

NOTE: Make all wiring conenctions using wire

connectors (supplied). Make sure that all

connections are tight, including ground, and that

no bare wire is visible at the wire connectors,

except for the ground wire.

Step 1. Remove faceplate and screws from

existing wall control (if present). Pull control out

from the wall box. Determine the "hot" wire and

"load" wire and disconnect these wires from

control (Fig. 24). Do not attempt to disconnect any

wires not already connected to existing control.

Caution: To reduce the risk of electrical shock,

disconnect the electrical supply circuit before

installing the fan, light kit or receiver.

Step 4. If you want to install the steel cap and

not the light kit. Assemble the steel cap to the

switch housing by twisting in a clockwise

direction. (Fig. 23)

Step 3. Secure the glass shade to switch

housing by twisting in a clockwise direction.

Do not over-tighten. (Fig. 22)

HOT BLK

BLACK

LOAD

GROUND

NEUTRAL

Switch Housing

Steel Cap

Fig. 22

Fig. 23

Switch Housing

Glass Shade

This manual suits for next models

Table of contents

Other Kichler Lighting Fan manuals

Kichler Lighting

Kichler Lighting BASICS PRO PREMIER 330016WH User manual

Kichler Lighting

Kichler Lighting 42 STRATMOOR User manual

Kichler Lighting

Kichler Lighting Golden Iridescence User manual

Kichler Lighting

Kichler Lighting Terra Select User manual

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB User manual

Kichler Lighting

Kichler Lighting Deckard User manual

Kichler Lighting

Kichler Lighting Kevlar 310150WCP User manual

Kichler Lighting

Kichler Lighting 310155 User manual

Kichler Lighting

Kichler Lighting True User manual

Kichler Lighting

Kichler Lighting Select Dorset User manual

Kichler Lighting

Kichler Lighting 300457 User manual

Kichler Lighting

Kichler Lighting KOSMUS User manual

Kichler Lighting

Kichler Lighting 65" GENTRY User manual

Kichler Lighting

Kichler Lighting Starkk User manual

Kichler Lighting

Kichler Lighting Bellamy User manual

Kichler Lighting

Kichler Lighting sterling manor select User manual

Kichler Lighting

Kichler Lighting Decor Kimberley User manual

Kichler Lighting

Kichler Lighting Starkk 330174OZ User manual

Kichler Lighting

Kichler Lighting 52" RENEW ENERGY STAR User manual

Kichler Lighting

Kichler Lighting Canfield 300117WH User manual

Kichler Lighting

Kichler Lighting FERRON User manual

Kichler Lighting

Kichler Lighting HATTERAS BAY PATIOLED 60" User manual

Kichler Lighting

Kichler Lighting Starkk 330180MWH User manual

Kichler Lighting

Kichler Lighting Select Sutter Place User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual