IOGear GWU647 User manual
Installation
Installation Guide
Universal 5-Port Wi-Fi N Ethernet Hub
GWU647
PART NO. M1200
3
Table of Contents
Package Contents 4
System Requirements 5
Product Overview 6
Installation 8
Installation without WPS - Windows XP 10
Installation without WPS - Windows Vista 16
Installation without WPS - Windows 7 24
Installation without WPS - Mac 32
Manual Set Up 37
Firmware Upgrade 41
Federal Communications Commission (FCC)
Statement 46
CE Compliance 47
SJ/T 11364-2006 48
Limited Warranty 49
Contact 50
4
Package Contents
• 1 X Universal 5-Port Wi-Fi N Ethernet Hub
• 1 X AC to USB Power Cable
• 1 X AC to USB Power Adapter
• 1 X Ethernet Cable
• 1 X Quick Start Guide
• 1 x Warranty Card
5
System Requirements
• Operating System
- Windows XP, Windows Vista, Windows 7
- Mac OS X v10.4 and above
• Wireless network with WPS setup
• Wireless network without WPS setup and computer
WPS
Reset PWR51 2 3 4
6
Product Overview
2 31
4
1. WPS Button
Push and hold the WPS button for
5~10 seconds to enable the WPS
feature.
2. Ethernet Port
The Ethernet port allows a LAN
connection through Cat 5 cables.
Supports auto-sensing at 10/100M
speed, half/ full duplex.
3. AC Power
AC Power Adapter
4. Reset Button
Push and hold the reset button for
5~10 seconds to reset the Wi-Fi
Hub to factory default setting
7
LED Indicator State Description
12 3 4
1. LAN LED
Flashing - Data is transmitting or
receiving on the LAN interface.
On - Port linked.
Off – No link.
2. WPS LED
Flashing - The WPS feature is enabled
and in use.
Off - The WPS feature is not in use.
3. WLAN LED
Flashing - WLAN is transmitting or
receiving data.
Off - WLAN is off
4. Power LED
On - Power on.
Off - Power off.
8
Installation
Wireless Setup with WPS
Step 1: Power on your Universal WiFi Hub using
either of these methods:
•ConnecttheACAdaptercabletoadevice.Make
sure that the device where you connect the AC
Adapter cable is powered on.
•ConnecttheWiFiHubtoanelectricaloutletwith
the included power adapter.
Note: It will take about 50 seconds to complete the
boot-up sequence. When complete, PWR (power)
LED will be active, and the WLAN Activity LED will
be blinking to show the WLAN interface is enabled.
Step 2: Use the included RJ-45 Ethernet cable to
connect the WiFi Hub with your device such as
Blu-ray player, HDTV, or game console.
Step 3: Refer to your wireless router’s user manual
to enable the WPS function, then press “WPS”
button on the back of WiFi Hub.
Your installation is complete. If asked for the type
of connection, make sure “WIRED” is selected on
your device.
WPS
Reset PWR51 2 3 4
9
Step 1
Step 3
Step 2
10
Installation without WPS - Windows XP
Step 1: Turn off your computer’s wireless
connection (if applicable) and disconnect the
Ethernet cable currently connect to your computer
(if applicable).
Step 2: Use the included RJ-45 Ethernet cable to
connect the WiFi Hub with your computer.
Step 3: Set your computer with a static IP address.
a. Right click on “My Network Places” and select
“Properties”.
Table of contents
Other IOGear Switch manuals
IOGear
IOGear MiniView GCS612A User manual
IOGear
IOGear GDP14W2 User manual
IOGear
IOGear 84B User manual
IOGear
IOGear Wireless USB Hub and Adapter Kit GUWH204KIT User manual
IOGear
IOGear GCS1002 User manual
IOGear
IOGear GUD3C04 User manual
IOGear
IOGear GUH420 User manual
IOGear
IOGear MiniView GCS632U User manual
IOGear
IOGear GCS1942H User manual
IOGear
IOGear MiniView Extreme GCS1732 User manual
IOGear
IOGear GHDMIS4 User manual
IOGear
IOGear GUH374 User manual
IOGear
IOGear GCS1722 User manual
IOGear
IOGear M1203 User manual
IOGear
IOGear MiniView GCS632U User manual
IOGear
IOGear GDPSP2 User manual
IOGear
IOGear GCS2HU User manual
IOGear
IOGear GUH227 User manual
IOGear
IOGear M1087-b User manual
IOGear
IOGear G-UH102 User manual
