Interlogix Ultra View UVD-6120VE-2 User manual

UltraView UVD-6120VE-2

Digital WDR Dome

Camera User Manual

P/N 1072553A • REV 1.0 • ISS 18JUN12

Trademarks and

patents

The

TruVision and Interlogix names and logo are trademarks of

UTC

Fire & Security.

Other trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products.

Manufacturer

UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

FCC compliance

Class A:

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated i

n a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own

expense.

ACMA compliance

Notice!

This is a Class A product. In a domestic environment this

product may cause

radio interference in which case the user may be

required to take adequate measures.

European Union

directives

12004/108/EC (EMC directive):

Hereby, UTC Fire & Security

declares that this device is in compliance or with the essential

requirements and ot

her relevant provisions of Directive 2004/108/EC

2002/96/EC (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local supplier

upo

n the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info.

Contact information

For contact information

, see www.utcfireandsecurity.com or

www.utcfssecurityproducts.eu

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 1

Content

Product overview 2

Package Contents 2

Features 2

User guidelines 2

Product description 3

OSD control pad 3

Installation 5

Mount the camera 5

Connect the cables 5

Adjust the lens 5

Adjust the focus and zoom 6

Programming 7

Access the Main menu 7

General menu 7

AE/WDR/BLC menu 8

WB mode menu 9

D/N mode menu 9

Motion alarm menu 10

Privacy menu 11

Picture adjustment menu 12

Reset camera 12

Specifications 12

Dimensions 13

Menu Map 14

2 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual

Product overview

The UVD-6120VE-2-XX camera uses a digital signal processor (DSP) to process

video signals. The camera includes a microcontroller to provide high-quality

images with high-color reproduction and sharp pictures.

Package Contents

The package contains the following:

• Dome camera

• Monitor output cable

• Mounting screws, wall anchors, and hex wrench

• Power terminal

• Ceiling drilling holes template

Note: Use the video output BNC and power jack for normal system operation.

Use the monitor output cable for installation and maintenance.

Features

The camera includes the following features:

• EXview HAD II (hole accumulated diode) technology with 480,000 pixels

NTSC (570,000 PAL)

• Use of LSI (large scale integration) digital processors to produce 650 lines of

horizontal resolution

• Smart digital control automatic BLC (backlight compensation)

• Digital wide dynamic range (WDR)

• Advanced auto exposure system for both fixed iris and auto iris lenses to

optimize the amount of light

• Internal synchronization

• Eight privacy mask areas to protect privacy concerns

• Advanced OSD (onscreen display) control

• Signal-to-noise ratio better than 52 dB

• Long life and high reliability

• Isolated switching power 12 VDC and 24 VAC

User guidelines

• Program the camera settings as much as possible before mounting the

camera. Take appropriate safety precautions while completing programming

after installation.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 3

• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the

camera.

• Do not use the camera over the temperature range specifications: - 22 to

122°F (-30 to +50°C).

• If the light source where the camera is installed experiences rapid, wide-

variations in lighting, the camera may not operate as intended.

WARNING: To reduce the risk of fire or electronic shock, do not expose the

camera to rain or moisture and do not remove the cover or back.

Product description

Figure 1:: Camera description

Camera body

OSD control

pad

System heater

Power jack

Monitor output cable:

1. Monitor output BNC; 2.

Monitor output RCA

Video monitor output Video output BNC

OSD control pad

The onscreen display (OSD) control pad (Figure 3) is a five-direction pad that

provides the ability to manually control the camera functions. Table 1 below lists

the OSD control pad functions and describes their use.

4 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual

Figure 2: OSD control pad

OSD control pad

Table 1: OSD control pad functions

Pad directions Description

Up Moves the cursor upward to select an item.

Left Moves the cursor left to select or adjust the options of the selected

item.

Right Moves the cursor to the right to select or adjust the options of the

selected item.

Down Moves the cursor downward to select an item.

Enter

Press the center of the control pad to display the Setup menu. If the

selected item has its own menu, press the control pad to enter a

submenu. Press the control pad for 2 seconds to save all settings

and exit the Setup menu.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 5

Installation

Please check the package contents and make sure that the device in the

package is in good condition and all the assembly parts are included.

To install the camera you will need to prepare the mounting surface, mount the

camera, make cable connections, adjust the lens and then secure the dome

cover securely.

Note: Before installing, please ensure that the mounting surface is strong enough

to withstand three times the weight of the camera. If the mounting surface is not

strong enough, the camera may fall and cause serious damage.

Mount the camera

Use the ceiling drilling holes template and mark the holes on the ceiling with a

pen. Attach the plate with fasteners to the ceiling and then attach the camera

body to the plate.

To mount the camera, attach the camera to the mounting surface using the

appropriate fasteners.

Connect the cables

To connect the cables:

1. Connect a coaxial cable from the camera’s BNC connector to a CCTV

monitor or video recording device.

2. Connect the 12 VDC or 24 VAC power supply to the power jack of the

camera.

Caution: Check for polarity when using a 12 VDC power supply.

Adjust the lens

The camera is mounted on a pan-tilt-twist (3-axis grimbal) rotating platform so

that it is easy to adjust the camera orientation. See Figure 3 on page 6.

6 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual

Figure 3: Camera adjustment

Platform horizontal adjustment (0 to 180°)

Platform vertical adjustment (0 to 90°)

Rotor horizontal adjustment (0 to 350°)

To adjust the lens:

See Figure 3 above.

1. To adjust the horizontal angle of the platform up to 180 degrees, turn the

platform.

2. To adjust the horizontal angle of the rotor up to 350 degrees, turn the rotor on

the platform.

3. To adjust the vertical angle of the platform up to 90 degrees, turn the

platform.

Adjust the focus and zoom

Figure 4: Zoom and focus adjustment

Zoom ring thumbscrew

Focus ring thumbscrew

To adjust the camera zoom and focus:

1. Loosen the zoom ring thumbscrew and turn the zoom ring to set the desired

zoom. Tighten the thumbscrew.

2. Loosen the focus ring thumbscrew and turn the focus ring to set the desired

focus. Tighten the thumbscrew.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 7

Programming

Access the Main menu

The Main menu provides access to the camera configuration options. The on-

screen display (OSD) is only available in English.

Program the camera by attaching a standard video monitor to the system.

Figure 5: The Main menu

To access the menus:

1. Press the OSD control pad to access the Main menu and its submenus.

2. Push the pad up, down, left and right to move between menu options.

3. Press the OSD control pad (Enter) to select an option.

4. When in a sub menu, select Return to return to the previous menu.

5. To exit the Main menu, move the cursor to Exit at the bottom of the screen

and press Enter. All changes are saved.

General menu

Select the General option from the Main menu to enter the General menu.

Figure 6: The General menu

Table 2: General menu

Parameter Description

ID display Displays the camera ID on screen. Default option is Off.

Mirror Flips the camera image so that it is correctly orientated for viewing.

8 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual

Parameter Description

Default option is Off.

DNR Digital noise reduction (DNR) improves the image quality in low light

levels.

When enabled, select the Y and C filter strength: Press Return to return

to the previous menu or Exit & Save to save changes and return to live

mode. Default option is On.

Return Press Enter to return to the previous menu.

Exit & Save Exits the menu and returns to live mode. Saves changes made.

AE/WDR/BLC menu

Select the AE/WDR/BLC option from the Main menu to enter the AE menu.

Figure 7: The AE/WDR/BLC menu

Table 3: AE/WDR/BLC menu

Menu item Description

Lens type Defines the lens type used with the camera.

Select Fixed or DC. If DC is enabled, select the DC level and shutter speed

from the options shown.

WDR/BLC set Wide dynamic range (WDR) allows you to see details of objects in shadows or

details of objects in bright areas of frames that have high contrast between

light and dark areas such as the headlights of a passing car.

Backlight compensation (BLC) function improves image quality when the

background illumination is high. It prevents the object in the center from

appearing too dark.

Options are:

•Off

•WDR: Set the luminance level ( Low, Middle, High)

•BLC fix: set the BLC level (between 1 and 30) and the BLC window.

AGC max Defines the automatic gain control (AGM).

Select a value between 0 and 160.

Flicker This feature to prevent the strobing effect under certain lighting

conditions/shutter speeds.

Default option is Off.

Return Press Enter to return to the previous menu.

Exit & Save Exits the menu and returns to live mode. Saves changes made.

This manual suits for next models

Table of contents

Other Interlogix Security Camera manuals

Interlogix

Interlogix TruVision TVB-2403 Instruction sheet

Interlogix

Interlogix TruVision TVB-2402 User manual

Interlogix

Interlogix TruVision TVD-7120VE-2 User manual

Interlogix

Interlogix UVD-XP4DNR(-P) User manual

Interlogix

Interlogix UltraView UVC-6130-1-N User manual

Interlogix

Interlogix TruVision TVD-2402 User manual

Interlogix

Interlogix UVD-XP4DNR(-P) User manual

Interlogix

Interlogix MobileView MVC-7100-29-BL User manual

Interlogix

Interlogix TruVision TVD-2401 User manual

Interlogix

Interlogix TruVision TVB-2402 User manual

Interlogix

Interlogix UltraView PTZ User manual

Interlogix

Interlogix UVP-N120P-36X(-P) User manual

Interlogix

Interlogix TruVision Open Standards User manual

Interlogix

Interlogix TruVision IP Dome User manual

Interlogix

Interlogix TruVision TVT-2101 User manual

Interlogix

Interlogix UVD-XP3DNR Assembly instructions

Interlogix

Interlogix TruVision TVB-2402 Instruction sheet

Interlogix

Interlogix TruVision TVD-2401 User manual

Interlogix

Interlogix TruVision TVD-N210V-2-N(-P) User manual

Interlogix

Interlogix UltraView IP PTZ 36X User manual

Interlogix

Interlogix TruVision TVC-7120-1-N User manual

Interlogix

Interlogix TruVision TVW-2401 User manual

Interlogix

Interlogix TruVision Line User manual

Interlogix

Interlogix TruVision TVD-2404 User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications