Intergraph TDZ 2000 GL1 User manual

TDZ 2000 GL1

Late-Breaking News

November 1998

DHA027590

and trademark law. This document may not, in whole or in part, be reproduced in any form or by any means, or be used to make any

derivative work, without written consent from Intergraph Computer Systems.

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of the

rights in technical data and computer software clause at DFARS 252.227-7013. Unpublished rights are reserved under the copyright

laws of the United States.

Intergraph Computer Systems, Huntsville AL 35894-0001

Notice

Information in this document is subject to change without notice and should not be considered a commitment by Intergraph Computer

Systems. Intergraph Computer Systems shall not be liable for technical or editorial errors in, or omissions from, this document.

Intergraph Computer Systems shall not be liable for incidental or consequential damages resulting from the furnishing or use of this

document.

All warranties given by Intergraph Computer Systems about equipment or software are set forth in your purchase contract. Nothing

stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such

warrantites.

Trademarks

Intergraph Computer Systems and the Intergraph Computer Systems logo are registered trademarks of Intergraph Computer Systems.

TDZ and Intense 3D are trademarks of Intergraph Computer Systems.

Other brands and product names are trademarks of their respective owners.

General

Matrox Millennium G200 AGP Graphics

If your system shipped with an installed Matrox Millennium G200 AGP video adapter, note

the following:

You can combine G200 with Matrox Millennium II PCI video display adapters for multi-

screen configurations.

If you must reinstall G200 driver software, use the MILL2DRVNT or MILL2DRVW95 driver

software, as appropriate.

For more information, see the Matrox documentation delivered with the system.

Three-Button Primax Mouse

If your system was delivered with a three-button Primax mouse, you may see a message that

says “MouseWare has detected a new Wheel Mouse....” and asks if you want to configure the

new device. If this happens, select No. If you experience any other anomalies while using the

Primax mouse, do the following:

If the system is running Windows NT 4.0, reinstall the mouse driver found on the

Windows NT software CD-ROM.

If the system is running Windows 95 or Windows 98, install the PMOUSE driver software

from the Intergraph System CD using InterSite Version Manager.

Logitech Wheel Mouse

If your system was delivered with a Logitech wheel mouse, you can find information on using

it by right-clicking the mouse icon in the taskbar tray, or by going to Start/Settings/Control

Panel/Mouse and clicking Help in the toolbar.

If the wheel on the mouse does not function, or if you experience any other anomalies while

using the wheel mouse, install theLMOUSE driver software from the Intergraph System CD

using InterSite Version Manager.

Microsoft Office Small Business Edition and

AutoMap Streets

If you purchased a system with Microsoft Office Small Business Edition, selected Office

products and Microsoft AutoMap Streets were installed before shipment. Installed products

include Word 97, Excel 97, Publisher 97, and Outlook 97. Note the following:

Microsoft Small Business Financial Manager was not installed on the system. To install

this product, run SETUP.EXE in the \OFF97SBE\SBFM directory on your system’s primary

hard disk drive. You will need the Microsoft Office media kit, and the CD-ROM and

license number it contains, during installation.

Microsoft Office ValuPack was not installed on the system. For information on installing

and using this product, see the VALUPK8.HLP file on the system’s primary hard disk drive.

AutoMap Streets was not installed if your system shipped with Windows 95. To install

this product on a system with Windows 95, run SETUP.EXE or AUTOUSS5.EXE from the

AutoMap Streets CD-ROM.

Operating System Support for USB Peripherals

Your system includes Universal Serial Bus (USB) ports to which you can connect USB

peripherals. Please note the following about support for USB peripherals in the operating

system version shipped with your system:

Windows 98 and Windows 95 Service Release 2.1 (or later) support USB peripherals.

Windows NT 4.0 does not support USB peripherals. Microsoft will add support for USB

peripherals to a future Windows NT release.

Windows NT 4.0

Ethernet Network Setup and Configuration

On a system equipped with an Ethernet network adapter, note the following:

Network adapter driver software is preinstalled. Operating system Setup no longer

prompts you to install networking.

Core network software and the NetBEUI network protocol are preinstalled. If you want

to connect the system to another type of network (such as TCP/IP), you must add the

appropriate network protocol using the Network applet in the Control Panel. Reinstall the

appropriate Windows NT 4.0 Service Pack software after making such changes, as

recommended by Microsoft.

3D Pipes Screen Saver and Dual-Screen

AccelSTAR II Graphics

On a system with dual-screen AccelSTAR II graphics, the 3D Pipes screen saver does not

display. If you activate this screen saver, you will only see a black screen. A driver fix for

this problem is under investigation. When available, a revised driver will be posted to the

Support pages on the World Wide Web (http://www.intergraph.com/ics/) and to the

Intergraph Bulletin Board Service (1-256-730-8786).

Enabling PC Card Hard Disk Operation

Intergraph Computer Systems has found a resource conflict that keeps a PC Card hard disk

(ATA or AT type) from being configured by Windows NT 4.0. To enable operation of a PC

Card hard disk in a PC Card adapter, you must edit the Windows NT Registry.

WARNING Be careful when making changes in the Registry. Any mistakes or incorrect changes

may cause serious operating system problems, and you may have to reinstall the

operating system. If the system becomes unusable after you have modified the

Registry, restart the system and try to use the Last Known Good configuration option to

undo the damage. See Windows NT documentation for more information on the Last

Known Good configuration option.

To enable PC Card hard disk operation:

1. Start the Registry Editor (REGEDT32.EXE) to open the Registry.

2. Open the following subkey in the Registry:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Pcmcia

3. From the Edit menu, select Add Value.

4. In the Value Name box, type InterruptMask.

5. In the Data Type box, select REG_DWORD; then select OK.

6. In the Data box, type F347.

7. Under Radix, select Hex; then select OK.

8. Exit from the Registry Editor.

9. Restart the system.

Windows 98 and Windows 95

Windows 98 and

System Setup

The System Setup document delivered with your system may contain Windows 95

information. If your system was delivered with Windows 98, refer to the following items for

information that replaces or supplements the Windows 95 information in the System Guide.

Windows 95 Drivers on Windows 98 Systems

Intergraph Computer Systems has preinstalled some Windows 95 drivers on systems delivered

with Windows 98. These drivers are provided as backup media in InterSite Version Manager.

Be sure to make copies of these drivers, as you may need them to reinstall the operating

system and associated system software. If you reinstall these drivers, you may be notified that

you are installing an outdated driver; ignore the prompt and continue installing the driver.

The installed Windows 95 drivers were certified on Windows 98, and can be used until

vendor-supplied Windows 98 versions are available. When they have been certified for use,

Windows 98 versions of these drivers will be posted to the Support pages on the World Wide

Web (http://www.intergraph.com/ics/) and to the Intergraph Bulletin Board Service (1-256-

730-8786).

Booting into Safe Mode

The graphics driver software installed on your system is set for a display resolution of 1024 x

768. If you connect the system to a monitor that does not support this resolution, the system

may boot into Safe Mode and the standard VGA display resolution of 640 x 480. If the

system boots into a distorted video display, you can restart the system and, before Windows

starts, press F8 to boot into Safe Mode.

Once the system is in Safe Mode, take the following steps:

1. Right-click the operating system desktop and select Properties.

2. In the Settings tab of the Display Properties dialog, set an appropriate display resolution

for the monitor and (if needed) an appropriate monitor type.

3. Restart the system to boot into Windows and the new display resolution.

System Power-Off After Shutdown

After you shut down Windows 98 or Windows 95 on a TDZ 2000 GL1, system power turns

off. This is a normal power management function of the system’s BIOS. However, if you

disable power management in the BIOS, system power still turns off after operating system

shutdown. This will be corrected in an upcoming BIOS version that will be posted to the

Support pages on the World Wide Web (http://www.intergraph.com/ics/) and to the

Intergraph Bulletin Board Service (1-256-730-8786).

Active Desktop (Windows 95)

On a system with Windows 95 OEM Service Release 2.5, when you start your system for the

first time, Internet Explorer installs at the end of Setup. You will notice that it takes several

minutes for Internet Explorer to complete its installation. After Internet Explorer installs,

Active Desktop is enabled by default, and appears as follows:

An active channel bar displays on the right side of the desktop.

The operating system’s desktop menus appear in a browser-style interface.

To disable Active Desktop:

1. Right-click the desktop, and then click Active Desktop−Customize my desktop.

2. In the Web tab of the Display Properties dialog, clear the check boxes for View My

Active Desktop as a Web Page and Internet Explorer Channel Bar.

3. You will be prompted that the wallpaper selected can be shown only with Active Desktop.

Select No, I do not want to enable Active Desktop, and then click OK.

Shutdown Hang (Windows 95)

On Windows 95 systems that have one or more network drives mapped, the computer may

hang during shutdown at the screen that says "Please wait while Windows 95 Shuts down the

computer...." This is caused by a bug in the Active Desktop component of Internet Explorer

4.0 (IE 4.0). You can work around this problem by disabling Active Desktop; see the

previous section for more information. You can resolve this problem by getting and installing

Service Pack 1 for IE 4.01 from http://www.microsoft.com/ie.

Installing 3Com Network Adapter Driver Software

(Windows 95)

On a Windows 95 system with a 3Com network adapter, the driver software is not

preinstalled. The first time the operating system starts, it detects the 3Com network adapter

and prompts you for the driver software. Install the driver software from the 3COM3C90X

diskettes. 3COM3C90Xis delivered as backup media in InterSite Version Manager or in the

3Com network adapter kit.

To install the 3Com network adapter driver software:

1. When prompted for a disk or CD-ROM that came with the device, insert diskette 2 into

the system’s floppy disk drive, and then click Next. Wait as directed for an updated

driver to be detected.

2. When prompted that Windows found the 3Com Fast Etherlink XL 10/100 Mb TX

Ethernet NIC (3C509B-TX), click Finish.

3. When prompted to insert a disk containing 3Com Etherdisk adapter software, insert

diskette 2 into the system’s floppy disk drive, and then click OK.

4. When a message displays that the W95EL90X.INF file could not be found, select to copy

files from A:\, and then click OK.

5. When prompted to insert Windows 95 disk 18, click OK.

6. When a message displays that the RPCLTC5.DLL file could not be found, select to copy

files from C:\WINDOWS\OPTIONS\CABS, and then click OK.

7. When prompted to insert 3Com Etherdisk adapter software disk 2, click OK.

8. When a message displays that the W95EL90X.INF file could not be found, select to copy

files from A:\, and then click OK.

Reinstalling the Intel PRO/100B EtherExpress

Driver Software (Windows 95)

If you reinstall the Intel PRO/100B EtherExpress network adapter driver on a Windows 95

system, be sure to read the instructions in the Intel documentation delivered with the adapter.

If the driver is not installed on the system, Windows 95 detects the network adapter and

prompts you to install the driver.

NOTE When installing the driver on a Windows 95 OSR 2.5 system, a notice may display that the

installation program wants to install files that are older than those on the system. Follow the

recommendation to keep the existing files.

While installing the driver, you are asked to insert Windows 95 Disk 1. The driver’s Setup

program is looking for the driver diskette delivered with the adapter. Make sure the diskette is

in the floppy disk drive, type the path to the diskette (typically a:\), and then click OK.

While installing the driver, you are asked to insert Windows 95 Disk 2. The driver’s Setup

program is looking for the Windows 95 Setup files. Do one of the following:

If you have a Windows 95 CD-ROM, insert the disc in the CD-ROM drive, type the path

to the Windows 95 files on the disc (typically d:\win95), and then click OK.

If the Windows 95 Setup files are available on the system disk, select OK. When the

Copying Files dialog displays with a message that theNETAPI.DLL file could not be found,

type the path to the Windows 95 Setup files (typically C:\WINDOWS\OPTIONS\CABS), and

then click OK.

Reinstalling Millennium II Driver Software and

MGA Powerdesk (Windows 98)

On a Windows 98 system with Millennium II graphics, the Millennium II driver software and

MGA Powerdesk software is preinstalled, and is available as backup media in InterSite

Version Manager (on multiple diskettes). If you have to reinstall Windows 98, do the

following to reinstall the Millennium II driver:

1. Let Windows 98 Setup detect the Millennium II graphics card. It will install the standard

PCI graphics adapter driver at VGA resolution.

2. After Windows 98 Setup completes, insert disk 1 of the Millennium II Windows 95 driver

(MILL2DRVW95) in the system’s floppy disk drive.

3. Right-click the desktop and go to Properties/Display/Settings/Advanced/Adapter.

4. Select to change the adapter.

5. In the Updated Device Driver Wizard, select to search for a better driver than the one

now in use.

6. When prompted, select the floppy disk drive containing disk 1 of MILL2DRVW95.

7. Follow the instructions to complete installation of the driver and restart the system.

To use the MGA Powerdesk features, you must reinstall the MGA Powerdesk software

separately, as follows:

1. Insert disk 1 of the Millennium II Windows 95 driver (MILL2DRVW95) in the system’s

floppy disk drive.

2. In Explorer, find and double-click the SETUP.EXE file on the diskette.

3. When prompted for an installation type, select the Typical option.

4. When prompted, remove disk 1 from the system’s floppy disk drive and insert disk 2.

5. Follow the instructions to complete installation of the Powerdesk software.

MGA Powerdesk includes support for Intergraph Computer Systems monitors. Take the

following steps to select the appropriate Intergraph monitor type:

1. Right-click the desktop and go to Properties/Settings/Advanced/MGA Monitor. The

MGA Monitor tab displays a monitor icon.

2. Select the appropriate Intergraph monitor from the list displayed.

Using Software for Zip or Jaz Drives (Windows 98)

If you purchased an Iomega Jaz or Zip drive with your system, the software included with the

drive options may not function properly in Windows 98. Iomega will release software that is

fully compatible with Windows 98 in August 1998. You will be able to get this software from

Iomega’s Web pages at http://www.iomega.com.

Reinstalling USB Support (Windows 95)

If you reinstall Windows 95 on the system, and you want to use the system’s Universal Serial

Bus (USB) ports, you must reinstall USB support software from the Windows 95

CD-ROM. See the USB.TXT file on the Windows 95 CD-ROM for instructions.

Reinstalling the Ensoniq AudioPCI Driver

Software (Windows 98)

If you reinstall Windows 98 on a system with an Ensoniq AudioPCI sound card, the card is

detected during Setup and listed as an “unknown device” because there is no driver for it in

Windows 98. To reinstall the Ensoniq driver, run the SETUP.EXE file found on the Ensoniq

software CD-ROM. This causes the Add New Hardware Wizard to run; when prompted,

select to display the list of drivers, and select Ensoniq AudioPCI from that list. When the Add

New Hardware Wizard completes, the Ensoniq Install Wizard continues; follow the

instructions displayed to complete the installation.

After the Ensoniq driver software has been installed, you must manually install the MS-DOS

support files. To do this, run the INITAP.BAT file found in the EAPCI directory on your system.

Other manuals for TDZ 2000 GL1

Table of contents

Other Intergraph Desktop manuals

Intergraph

Intergraph TDZ 2000 GL2 Workstation User manual

Intergraph

Intergraph TDZ-300 Operating manual

Intergraph

Intergraph TDZ 2000 GL1 User manual

Intergraph

Intergraph TDZ 2000 GL2 Workstation User manual

Intergraph

Intergraph TD-2x User manual

Intergraph

Intergraph TD-260 Parts list manual

Intergraph

Intergraph TDZ 2000 GL1 User guide

Intergraph

Intergraph TD-300 Operating manual

Intergraph

Intergraph Zx1 ViZual Workstation Parts list manual

Intergraph

Intergraph TD-200 Targa 2000 User manual

Intergraph

Intergraph TD-20 Setup User guide

Intergraph

Intergraph TD-x10 Setup User guide

Intergraph

Intergraph TDZ 2000 GX1 User manual

Intergraph

Intergraph TDZ 2000 GT1 User manual

Intergraph

Intergraph TDZ 2000 GL2 Workstation User manual

Intergraph

Intergraph TDZ-400 Deskside Operating manual

Intergraph

Intergraph TD-325 Targa 2000 User manual

Intergraph

Intergraph TDZ 2000 GX1 User manual

Intergraph

Intergraph TD-22x Parts list manual

Intergraph

Intergraph TDZ 2000 User manual

Intergraph

Intergraph Zx10 6U Parts list manual

Intergraph

Intergraph Zx1 ViZual Workstation User guide

Intergraph

Intergraph TD-x20 Setup User guide

Intergraph

Intergraph Zx10 Ultra-Tower User manual

Popular Desktop manuals by other brands

HP m9060n - Pavilion - Elite Quick setup

Asus

Asus E210 Series user guide

Dell

Dell Inspiron 600m quick start

Dell

Dell Inspiron 3662 Service manual

TotalFlow

TotalFlow uFLO user manual

HP Presario SV7000 - Desktop PC manual

HP ProDesk 400 G5 Maintenance and service guide

Logitech

Logitech MK320 quick start guide

Dell

Dell XPS 730 H2C Service manual

Sony

Sony Vaio Series operating instructions

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer quick start

Alto

Alto MD 250 instruction manual

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series user manual

Sony

Sony VAIO VGX-TP1 Series user guide

Asus

Asus Eee Box B204 user manual

Dell

Dell Optiplex 9010 All In One owner's manual