IFM PN01 A Series User manual

Operating instructions
Pressure sensor
PN01xA
706232 / 01 01 / 2019
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������3
1�1 Symbols used ������������������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������3
3 Functions and features ����������������������������������������������������������������������������������������4
4 Function���������������������������������������������������������������������������������������������������������������4
4�1 Communication, parameter setting, evaluation ���������������������������������������������4
4�2 Switching function������������������������������������������������������������������������������������������5
4�3 Diagnostic function ����������������������������������������������������������������������������������������5
5 Installation������������������������������������������������������������������������������������������������������������6
6 Electrical connection��������������������������������������������������������������������������������������������6
7 Operating and display elements ��������������������������������������������������������������������������7
8 Menu��������������������������������������������������������������������������������������������������������������������8
8�1 Menu structure�����������������������������������������������������������������������������������������������8
8�2 Explanation of the menu��������������������������������������������������������������������������������9
9 Parameter setting ����������������������������������������������������������������������������������������������10
9�1 Parameter setting in general �����������������������������������������������������������������������10
9�2 Configure display (optional)�������������������������������������������������������������������������12
9�3 Set output signals ����������������������������������������������������������������������������������������12
9�3�1 Set the output function������������������������������������������������������������������������12
9�3�2 Set switching limits �����������������������������������������������������������������������������12
9�4 User settings (optional)��������������������������������������������������������������������������������13
9�4�1 Set delay for the switching outputs�����������������������������������������������������13
9�4�2 Set output logic for the switching outputs �������������������������������������������13
9�4�3 Set damping for the switching outputs������������������������������������������������13
9�5 Service functions �����������������������������������������������������������������������������������������13
9�5�1 Read min/max values for the system pressure ����������������������������������13
9�5�2 Reset all parameters to factory setting �����������������������������������������������13
10 Operation���������������������������������������������������������������������������������������������������������14
10�1 Read set parameters ���������������������������������������������������������������������������������14
10�2 Error indications�����������������������������������������������������������������������������������������14
10�3 Setting ranges �������������������������������������������������������������������������������������������14

3
UK
1 Preliminary note
1.1 Symbols used
►Instruction
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunction or interference�
Information_Supplementary note�
2 Safety instructions
• Please read the product description prior to set-up of the unit� Ensure that the
product is suitable for your application without any restrictions�
• If the operating instructions or the technical data are not adhered to, personal
injury and/or damage to property can occur�
• Check the compatibility of the product materials with the media to be measured
in all applications� You can find information about the product materials in the
technical data sheet (or → chapter 12 Technical data).
• Please adhere to the notes on safe use in hazardous areas: → Operating
instructions (Ex protection related part) for pressure sensors according to the
EU directive 2014/34/EU annex VIII (ATEX) group II, equipment category 3D.
If no operating instructions (Ex protection related part) or EC declaration of
conformity is supplied with this product in the language of the EU user country,
these can be requested from your dealer (see delivery note) or manufacturer
(see cover sheet / back)�
11 Scale drawing ��������������������������������������������������������������������������������������������������15
12 Technical data��������������������������������������������������������������������������������������������������15
13 Factory setting �������������������������������������������������������������������������������������������������17

4
3 Functions and features
The unit monitors the system pressure of machines and installations.
Applications
Type of pressure: relative pressure
Order no. Measuring range Permissible
overload pressure Bursting pressure
bar PSI bar PSI bar PSI
PN014A -1���10 -14�5���145 75 1 087 150 2 175
PN016A 0�2���5 0�36���3 20 290 50 725
MPa = bar ÷ 10 / kPa = bar × 100
Avoid static and dynamic overpressure exceeding the given overload
pressure by taking appropriate measures�
The indicated bursting pressure must not be exceeded.
Even if the bursting pressure is exceeded only for a short time, the unit
may be destroyed. NOTE: risk of injury!
4 Function
4.1 Communication, parameter setting, evaluation
• The unit displays the current process value.
• It generates 2 output signals according to the parameter setting�
OUT1 • Switching signal for process value; IO-Link�
OUT2
2 options
• Switching signal for process value�
• Diagnostic signal (output 2 is inactive in case of a fault)�
• The following functions are available via IO-Link (OUT1): Reading the current
process value, changing parameters and transferring them to other units of the
same type using the FDT service program ifm Container or other parameter
setting tools with IO-Link capability. The program library of the available DTM
objects and the IO Device Description (IODD) are available at www.ifm.com →
Service → Download.

5
UK
4.2 Switching function
OUTx changes its switching state if it is above or below the set switching limits
(SPx, rPx). The following switching functions can be selected:
• Hysteresis function / normally open: [OUx] = [Hno] (→ fig. 1).
• Hysteresis function / normally closed: [OUx] = [Hnc] (→ fig. 1).
First the set point (SPx) is set, then the reset point (rPx) with the requested
difference�
• Window function / normally open: [OUx] = [Fno] (→ fig. 2).
• Window function / normally closed: [OUx] = [Fnc] (→ fig. 2).
The width of the window can be set by means of the difference between SPx and
rPx� SPx = upper value, rPx = lower value�
1 2
P = system pressure; HY = hysteresis; FE = window
4.3 Diagnostic function
Output 2 is used as diagnostic output based on the DESINA specification if [OU2]
= [dESI]�
• If there is no fault, the output is switched and carries UB+ (if P-n = PnP) or UB-
(if P-n = nPn)�
• In case of malfunctions the output becomes inactive. The following
malfunctions are detected:
- measuring cell defective;
- short circuit in output 1

6
5 Installation
Before installing and removing the unit: Make sure that no pressure is
applied to the system�
►Insert the unit in a G¼ process connection�
► Tighten firmly.
6 Electrical connection
The unit must be connected by a qualified electrician.
The national and international regulations for the installation of electrical
equipment must be adhered to.
Voltage supply to EN 50178, SELV, PELV�
►Disconnect power�
►Connect the unit as follows:
2 x positive switching 2 x negative switching
Pin 1 Ub+
Pin 3 Ub-
Pin 4 (OUT1) • Binary switching output; IO-Link
Pin 2 (OUT2) • Binary switching output if [OU2] = [Hno], [Hnc], [Fno] or [Fnc]
• Diagnostic output if [OU2] = [dESI]
Core colours of ifm sockets:
1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

7
UK
7 Operating and display elements
1 to 8: indicator LEDs
- LED 1 to LED 3 = system pressure in the unit of measurement which is indicated on the
label�
- LEDs 4 - 6 not used�
- LED 7, LED 8 = switching state of the corresponding output�
9: Alphanumeric display, 4 digits
- Display of the current system pressure�
- Indication of the parameters and parameter values�
10: Set button
- Setting of the parameter values (scrolling by holding pressed; incrementally by pressing
once)�
11: Mode/Enter button
- Selection of the parameters and acknowledgement of the parameter values�

8
8 Menu
8.1 Menu structure

9
UK
8.2 Explanation of the menu
SP1/rP1 Upper / lower limit value for system pressure at which OUT1 switches.
SP2/rP2 Upper / lower limit value for system pressure at which OUT2 switches.
OU1 Output function for OUT1:
• Switching signal for the pressure limit values: hysteresis function [H ��] or
window function [F ��], either normally open [� no] or normally closed [� nc]�
OU2 Output function for OUT2:
• Switching signal for the pressure limit values: hysteresis function [H ��] or
window function [F ��], either normally open [� no] or normally closed [� nc]�
• Diagnostic signal [OU2] = dESI
EF Extended functions / opening of menu level 2�
Uni Standard unit of measurement for system pressure�
HI Maximum value memory for system pressure�
LO Minimum value memory for system pressure (only PN014A)�
dS1/dS2 Switch-on delay for OUT1 / OUT2.
dr1/dr2 Switch-off delay for OUT1 / OUT2.
P-n Output logic: pnp / npn�
dAP Damping for the switching outputs�
diS Update rate and orientation of the display�
rES Restore factory setting�

10
9 Parameter setting
During parameter setting the unit remains in the operating mode� It continues its
monitoring functions with the existing parameters until the parameter setting has
been completed�
9.1 Parameter setting in general
3 steps must be taken for each parameter setting:
1Select parameter
►Press [Mode/Enter] until the
requested parameter is displayed.
2Set parameter value
►Press [Set] and keep it pressed�
> Current setting value of the
parameter flashes for 5 s�
> After 5 s: setting value is changed:
incrementally by pressing once or
scrolling by holding pressed�
Numerical values are incremented continuously� For reducing the value: let the
display move to the maximum setting value. Then the cycle starts again at the
minimum setting value�
3Acknowledge parameter value
►Press [Mode/Enter] briefly�
> The parameter is displayed again.
The new setting value is saved.
Set other parameters
►Start again with step 1�
Finish parameter setting
►Press [Mode/Enter] several times until the current measured value is displayed or wait
for 15
s�
> The unit returns to the operating mode.
• If [SLoc] is displayed when attempting a modification of a parameter value, the
sensor is locked by the software. This locking can only be removed using a
parameter setting software�
This manual suits for next models
2
Table of contents
Other IFM Accessories manuals

IFM
IFM O5E5 Series User manual

IFM
IFM OY Series User manual

IFM
IFM OGD582 User manual

IFM
IFM PI109 Series User manual

IFM
IFM efector 200 O4P2 Series User manual

IFM
IFM UGT203 User manual

IFM
IFM O5D15 Series User manual

IFM
IFM UGT20 Series User manual

IFM
IFM OGH3 Series User manual

IFM
IFM SB1 Series User manual































