IFM OGH3 Series User manual
Operating instructions
Diffuse reflection sensor
with background suppression
OGH3xx
OGH5xx
UK
704073 / 03 11 / 2019
2
1 Functions and features
The diffuse reflection sensor detects objects and materials without contact and
indicates their presence by a switching signal.
For the range see the type label (on white paper 200x200 mm, 90 % remission).
2 Installation
►Align the diffuse reflection sensor to the object to be detected.
►Secure the unit to a bracket.
The objects to be detected are to move
transversally to the lens of the sensor.
In case of other directions of movement it
should be tested before whether the swit-
ching function is guaranteed.
3 Electrical connection
►Disconnect power.
►Connect the unit as follows.
Cable Connector Pin connection
L+ BN pin 1
L- BU pin 3
load BK pin 4
load *) WH *) pin 2 *)
Core colours BN = brown, BU = blue, BK = black
*) Seulement pour des appareils avec sortie antivalente.
UK
3
4 Operating and display elements
1: LED
2: [OUT o]
3: [OUT on]
4 Settings
4.1 The sensor is to switch when the object is detected
1
►Position the object.
► Press [OUT on] for 2 s.
> The sensitivity is set to the object.
> The LED flashes.
2
►Remove the object.
► Press [OUT off].
> The sensitivity is set without object.
> The LED goes out. The programming is finished.
4.2 The sensor is not to switch when the object is detected
► Position the object (see figure 1) and press [OUT off] for 2
s.
► Remove the object (see figure 2) and press [OUT on].
The settings can also be carried out first without object and then with object.
4
4.3 Programming unsuccessful
> LED flashes quickly, 8 Hz.
Possible causes
• Measured value difference too small.
• Max. programming time of 15 min. exceeded.
4.4 Setting of maximum sensitivity
►Align the sensor so that no light is reflected.
The sensor is to switch when the object is detected
► First press [OUT on] and then [OUT off].
The sensor is to switch when the object is not detected
► First press [OUT off], then [OUT on].
4.5 Locking or unlocking the buttons
The unit can be locked electronically to prevent unintentional settings.
► Press [OUT on] and [OUT off] simultaneously for
10 s.
> Acknowledgement is indicated by a change of the
LED status.
5 Operation
►Check whether the unit operates correctly.
> The LED lights when the switching output is switched.
6 Maintenance
►Keep the lens of the sensor free from soiling.
►For cleaning do not use any solvents or cleaning agents which could damage
the plastic lens.
Technical data and further information at www.ifm.com
UK
5
This manual suits for next models
1
Table of contents
Other IFM Accessories manuals
IFM
IFM Efector 160 LR70 User manual
IFM
IFM PI28 Series User manual
IFM
IFM O6P7 Series User manual
IFM
IFM SB1 Series User manual
IFM
IFM O2D54 Series User manual
IFM
IFM efector 200 OGH User manual
IFM
IFM OY Series User manual
IFM
IFM O5H5 Series User manual
IFM
IFM UGR500 User manual
IFM
IFM Efector 200 OG User manual
IFM
IFM LT80 Series User manual
IFM
IFM LR3009 User manual
IFM
IFM OGH User manual
IFM
IFM LI513 Series User manual
IFM
IFM efector200 OM User manual
IFM
IFM PN01 A Series User manual
IFM
IFM Efector 200 O4P5 Series User manual
IFM
IFM Efector 200 OJ User manual
IFM
IFM Efector 180 IX5030 User manual
IFM
IFM 402946 User manual
