IFM MN7 S Series User manual

Original operating instructions
RFID-coded safety sensor
MN7xxS UK
80256459 / 00 01 / 2018

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������3
1�1 Symbols used ������������������������������������������������������������������������������������������������3
1�2 Warning signs used ���������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������4
2�1 Safety-related requirements regarding the application����������������������������������4
2�2 Radio equipment �������������������������������������������������������������������������������������������5
2�3 Interference of electronic and medical devices ���������������������������������������������6
3 Items supplied������������������������������������������������������������������������������������������������������6
4 Functions and features ����������������������������������������������������������������������������������������6
5 Function���������������������������������������������������������������������������������������������������������������7
5�1 Limit range and operating range��������������������������������������������������������������������7
6 Installation������������������������������������������������������������������������������������������������������������8
6�1 Actuating directions ���������������������������������������������������������������������������������������8
7 Electrical connection��������������������������������������������������������������������������������������������9
8 Programming �����������������������������������������������������������������������������������������������������10
9 Operation����������������������������������������������������������������������������������������������������������� 11
9�1 Switching state of the outputs���������������������������������������������������������������������� 11
9�1�1 The safe state������������������������������������������������������������������������������������� 11
9�1�2 The switched state������������������������������������������������������������������������������ 11
9�1�3 Cross fault / short circuit��������������������������������������������������������������������� 11
9�2 Interface classification ��������������������������������������������������������������������������������� 11
9�2�1 Identification key��������������������������������������������������������������������������������� 11
9�3 LED display �������������������������������������������������������������������������������������������������12
9�3�1 5-wire design ��������������������������������������������������������������������������������������12
9�3�2 8-wire design ��������������������������������������������������������������������������������������13
10 Technical data��������������������������������������������������������������������������������������������������14
10�1 Drawing������������������������������������������������������������������������������������������������������16
11 Troubleshooting �����������������������������������������������������������������������������������������������16
12 Maintenance, repair and disposal��������������������������������������������������������������������17
13 Terms and abbreviations����������������������������������������������������������������������������������17

3
UK
1 Preliminary note
The instructions are part of the unit� They are intended for authorised persons ac-
cording to the EMC, Low Voltage and Machinery Directive and safety regulations�
The instructions contain information about the correct handling of the product�
Read the instructions before use to familiarise yourself with operating conditions,
installation and operation�
Follow the safety instructions�
1.1 Symbols used
►Instructions
> Reaction, result
→Cross-reference
Important note
Non-compliance may result in malfunction or interference�
Information
Supplementary note�
LED lights green
LED lights red
LED lights orange
LED lights green, red or orange
LED flashes
LED off
1.2 Warning signs used
WARNING
Warning of serious personal injury�
Death or serious irreversible injuries may result�
14 Approvals/standards ����������������������������������������������������������������������������������������18
14�1 FCC Notices (USA, Canada)���������������������������������������������������������������������18

4
2 Safety instructions
• Follow the operating instructions�
• Improper use may result in malfunctions of the unit� This can lead to personal
injury and/or damage to property during operation of the machine� For this rea-
son note all remarks on installation and handling given in this document� Also
adhere to the safety instructions for the operation of the whole installation�
• In case of non-observance of notes or standards, especially when tampering
with and/or modifying the unit, any liability and warranty is excluded�
• If the sensor is damaged, the safety function cannot be guaranteed�
• Errors caused by damage cannot be detected by the sensor�
• The unit must be installed, connected and put into operation by a qualified
electrician trained in safety technology�
• The applicable technical standards for the corresponding application must be
complied with�
• For installation the requirements according to EN 60204 must be observed�
• In case of malfunction of the unit please contact the manufacturer� Tampering
with the unit is not allowed�
• Disconnect the unit externally before handling it� Also disconnect any inde-
pendently supplied relay load circuits�
• After installation, maintenance or repair of the system perform a complete
function check�
• Only use the unit under the specified operating conditions (→ 10 Technical
data)� In case of special operating conditions please contact the manufacturer�
• Use only as described below (→ 4)�
2.1 Safety-related requirements regarding the application
It must be ensured that the safety requirements of the respective application
correspond to the requirements stated in these instructions�

5
UK
WARNING
Failure of the safety function
When used outside of the defined environmental conditions, the safety-related
function of the sensor cannot be guaranteed�
►Use only in accordance with the defined environmental conditions (→ 10
Technical data)�
Use of the sensor in the vicinity of chemical and biological media (solid, liquid,
gaseous) as well as ionising radiation is not permitted�
Observe the following requirements:
►Only use cable glands, insulation material and connection wires that have an
appropriate protection rating�
►Adhere to ISO 14119 for interlocking devices associated with guards�
►Adhere to the principle of normally closed operation for all external safety
circuits connected to the system�
►The device must not be installed or operated in the environment of strong
magnetic fields�
►Do not use the device as an end stop�
►In case of faults within the sensor which result in the defined safe state: Take
measures to maintain the safe state when the complete control system contin-
ues to be operated�
►Sensors and actuators must be protected from strong shocks and vibrations�
Observe the permissible environmental conditions (→ 10 Technical data)�
►Annual function test (→ 12 Maintenance, repair and disposal)�
►Replace damaged units�
2.2 Radio equipment
In general, the device must not be used in the vicinity of petrol stations, fuel de-
pots, chemical plants or blasting operations�
►Do not transport and store any flammable gases, liquids or explosive substanc-
es near the unit�

6
2.3 Interference of electronic and medical devices
Operation of the unit can affect the function of electronic devices that are not
correctly shielded�
►Disconnect the device in the vicinity of medical equipment�
►Contact the manufacturer of the corresponding device in case of any interfer-
ence�
3 Items supplied
1 RFID-coded safety sensor, 1 RFID-coded actuator,
4 washers, 8 cover caps,
1 x original operating instructions, ident number 80256459�
If one of the above-mentioned components is missing or damaged, please contact
one of the ifm branch offices�
4 Functions and features
RFID-coded safety sensors detect the corresponding actuators (ID-tags) without
contact�
Coding levels according to EN ISO 14119:
Sensor type Performance Coding level
Coded Each sensor recognises each actuator of this type� low
Codable The sensor can be programmed for a specific actuator� low
Unique coding The sensor only detects the actuator with the corre-
sponding coding�
high
Safety-related function SF: The safe state (output stage switched off; Logic "0") is
achieved if the distance to the actuator is greater than or equal to the safe switch
off distance sar (→ 10 Technical data)�
►Observe the notes on installation (→ 6 Installation)�
The RFID-coded safety sensor has been certified by TÜVSüd�

7
UK
5 Function
ACT
IN
OUT
PWR
1
LED
2
Operating area
3
Switch-on distance sn (= 12 mm)
4
Limit range
5
Safe switch-off distance sar (= 16 mm)
5.1 Limit range and operating range
LED states when aligning the sensor with the actuator
Status Description LED
PWR
OUT
IN *)
ACT
ACT
IN
OUT
PWR
Actuator outside the limit area
4
Nominal voltage connected
> Inputs active
> Outputs deactivated
ACT
IN
OUT
PWR
Actuator within the actuating area
2
> Outputs activated
ACT
IN
OUT
PWR
Actuator leaves actuating area
2
and is in the
limit area
4
> Outputs remain active
ACT
IN
OUT
PWR
The distance of the actuator to the sensor is larger
than or equal to sar
5
> Outputs deactivated
*)LED [IN] is not on in case of MN700S and MN703S�

8
Approach curves of the sensors at www�ifm�com:
→ General information about mounting and operation
6 Installation
6.1 Actuating directions
The sensor recognises the actuator from three different directions
2
�
►When mounting the device, align the central marks
1
of the sensor and the actuator
in parallel to each other�
1
2
1
Reference marks (central mark)
2
Actuating direction
• The actuator must not touch the sensor during operation�
• Do not adjust the device using mechanical force�
• Only mount on a flat surface to avoid damage or changes of the sensing range�
When using several sensors, a minimum distance of 50 mm in each direc-
tion must be maintained�
►Fasten the sensor and the actuator with two screws each (M4, > 18 mm) (tight-
ening torque 0�8���2 Nm)�
Using less than two screws for each component is not permissible�
According to EN ISO 14119, the actuator must be fixed immovably�
Safety screws with one-way heads, rivets or the like are to be used�
After mounting, insert the supplied cover caps to make it more difficult to access
screws or rivets�

9
UK
7 Electrical connection
►Disconnect power� Also disconnect any independently supplied relay load
circuits�
Cable Connector
BK: black RD: red
BN: brown VT: violet
BU: blue WH: white
4
2 1
3
5
6
21
45
7
38
OS1
OS2
O3
IN1
IN2
+
L
L
BN
RD/WH
BK/WH
BK
BU
RD
OS1
OS2
O3
1
2
3
4
5
IN1
IN2
+
L
L
PVC cable, 6 x 0�5 mm² M12 connector, 5-pole
OS1
IN1
BN
BU
IN2
+
L
L
RD
VT
RD/WH
BK/WH
BK
VT/WH
IN2
OS2
IN1
O3 2
OS1
IN1
1
3
IN2
+
L
L
2
6
4
7
5
8
IN2
OS2
IN1
O3
IN3
2
PVC cable, 8 x 0�34 mm² M12 connector, 8-pole
1
Safety-related logic unit
2
Programmable Logic Controller (PLC)
3
Programming input (MN702S, MN705S)
In case of a single fault, the supply voltage must not exceed a maximum
of 60 V DC� (This requires the safe separation between power supply and
transformer SELV / PELV�)
The maximum permitted cable length is 50 m�

10
8 Programming
The programmable version of the sensor is provided with a special programming
input (IN3) that recognises the stored code in a new actuator�
The programming can be repeated as often as you like� After successful program-
ming, the sensor will only recognise the code of the most recently programmed
actuator�
The sensor may only be programmed by qualified staff�
LED Status Description
PWR
OUT
IN
ACT
Switch-on operation ►Connect the sensor to the nominal voltage�
> The device executes internal tests�
Operation Waiting for the input signal�
Operation Input signals available�
Waiting for actuator�
Programming
►Activate the programming input IN3 by con-
necting the nominal voltage (> 3 s)�
> Waiting for actuator�
Programming ►Hold the new actuator to the sensor�
> New code is successfully stored�
Programming ►Deactivate programming input IN3�
> Programming finished�
Switch-on operation Automatic restart
> The device executes internal tests�
LED green LED red LED orange
LED flashes LED green, red or orange LED off
►After successful programming, test if the new actuator is recognised and the
sensor functions properly�
This manual suits for next models
6
Table of contents
Other IFM Accessories manuals

IFM
IFM SBY2 Series User manual

IFM
IFM PN3 Series User manual

IFM
IFM Efector 500 PI2652 User manual

IFM
IFM O1D120 User manual

IFM
IFM O5D10 Series User manual

IFM
IFM Efector 100 GG712S User manual

IFM
IFM O5H5 Series User manual

IFM
IFM O2D54 Series User manual

IFM
IFM OGE7 Series User manual

IFM
IFM O1D100 series User manual































