IFM Electronic Efector200 OL User manual

Operating instructions

Diffuse reflection sensor

701271 / 04 12 / 2010

Contents

Function and features��3

Electrical connection��3

Montage��4

Commissioning��4

Setting of the sensitivity with stationary objects ��5

Setting of the sensitivity with moving objects ��6

Setting of the maximum sensitivity ��7

Programming the output function ��7

Operation��8

Maintenance��8

Function and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switched signal�

Range (r): see type label (value referred to white paper 200 mm x 200 mm)�

Electrical connection

►Isolate power, then connect the unit�

►Connect the unit as follows:

AC/DC Relais

Sensor with terminals Sensor with connector































Insert a miniature fuse according to the technical data sheet, if specified�

Core colours (for sensors with cable connection): BN = brown, BU = blue,

BK = black, WH = white�

Programming of the output function by push button (see page 7)�

The units with cable gland have a removable terminal block with screw terminals

(screws are at the base of the terminal block)�

After connection of the wires the terminal block must be reinserted�

Check the unit for reliable function after a short cirucit�

Montage

1: LEDs red, green, yellow

2: Pushbutton

3: LED yellow

Align the photocell and fasten it to a mounting bracket�

Maximum range is only possible with precise alignment�

Commissioning

The diffuse reflection sensor is supplied ready to operate (plug and play) set at the

max� sensing range� This is sufficient if the diffuse reflection sensor can operate

with maximum excess gain (highest contrast)�

The following setting procedures should only be necessary in less straightforward

applications, for example if a background must be „tuned out“�

Setting of the sensitivity with stationary objects

►Activate the programming mode of the unit without object�

►Press for about 2 s until the red LED flashes�

> The red LED goes out; the yellow and green LEDs flash alternately�

> The unit is in the programming mode�

Setting with object�

►Press once�

> The yellow and green LEDs go out for approx� 1 s, then flash again alternately�

Setting without object�

►Press once�

> The yellow and green LEDs go out for approx� 1 s�

> After approx� 3 s the green LED is on�

> The unit is in the operating mode��

You can also proceed in reverse order: first setting without the object, then with

the object�

If the setting of the sensitivity is not possible (e�g� object signal and

background signal are about the same), the red LED flashes after step

3 for approx� 2 s� The unit then passes into the operating mode with the

sensitivity being unchanged�

If the setting button is not activated for 15 minutes during the programming

process, the unit passes automatically into the operating mode with the sensitivity

being unchanged�

Setting of the sensitivity with moving objects

►Activate the programming mode of the unit without object�

►Press for about 2 s until the red LED flashes�

> The red LED goes out; the yellow and green LEDs flash alternately�

> The unit is in the programming mode�

►During the measurement (approx� 1 s) allow at least two objects to move through

the sensing area of the lens�

►Press once�

> The yellow and green LEDs go out for approx� 1 s, then flash again alternately�

►During the measurement (approx� 1 s) allow at least two objects to move through

the sensing area of the lens�

►Press once�

> The yellow and green LEDs go out for approx� 1 s�

> After approx� 3 s the green LED is on�

> The unit is in the operating mode�

If the setting of the sensitivity is not possible (e�g� object signal and

background signal are about the same), the red LED flashes after step

3 for approx� 2 s� The unit then passes into the operating mode with the

sensitivity being unchanged�

Setting of the maximum sensitivity

• Go into the programming mode (step 1)�

• Align the unit so that no light is reflected�

• Press the setting button twice (see steps 2 and 3)�

Programming the output function

►Press for 10 s�

The red LED starts to flash fast after 2 s�

Then the yellow and green LEDs flash

alternately� After 8 s all LEDs go off,

the output function has changed from

light-on mode to dark-on mode (or vice

versa)�

Operation

Check the safe functioning of the sensor� Display by LEDs�

LED green lights Unit is ready for operation�

LED yellow lights Output is switched�

LED red lights Error in object detection, e�g� maladjustment,

soiling of the lenses�

LEDs yellow + red

Flash alternately, 2 Hz: output short-circuited�

Flash alternately, 1 Hz: internal malfunction,

(output is not switched)�

Maintenance

Keep the lens of the sensor free from soiling�

For cleaning do not use any solvents or cleaning agents which could damage the

plastic lenses�

This manual suits for next models

Table of contents

Other IFM Electronic Accessories manuals

IFM Electronic

IFM Electronic O1D100 User manual

IFM Electronic

IFM Electronic efector 190 DTE820 User manual

IFM Electronic

IFM Electronic efector 300 SU7000 User manual

IFM Electronic

IFM Electronic efectro 500 User manual

IFM Electronic

IFM Electronic efector 200 OJ51 Series User manual

IFM Electronic

IFM Electronic efector 300 SM7001 User manual

IFM Electronic

IFM Electronic efector200 OT Series User manual

IFM Electronic

IFM Electronic Efector 150 KG5070 User manual

IFM Electronic

IFM Electronic Efector 200 OI Series User manual

IFM Electronic

IFM Electronic PN7000 User manual

IFM Electronic

IFM Electronic Ecomat 100 CR2102 Application guide

IFM Electronic

IFM Electronic efector180 IX5010 User manual

IFM Electronic

IFM Electronic Efector 500 PL2058 User manual

IFM Electronic

IFM Electronic Efector 200 User manual

IFM Electronic

IFM Electronic KQ5 Series User manual

IFM Electronic

IFM Electronic efector 500 PM2055 User manual

IFM Electronic

IFM Electronic efector 300 SU8001 User manual

IFM Electronic

IFM Electronic efector160 LI51 User manual

IFM Electronic

IFM Electronic Efector 300 User manual

IFM Electronic

IFM Electronic Efector500 PF2058 User manual

IFM Electronic

IFM Electronic efector 300 SU8200 User manual

IFM Electronic

IFM Electronic efector200 OJ51 Series User manual

IFM Electronic

IFM Electronic efector 250 O2D2 Series Owner's manual

IFM Electronic

IFM Electronic efector 200 OPU200 User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit instruction manual

IFM Electronic efector200 OL User manual

Popular Accessories manuals by other brands