IFM Electronic Efector 200 User manual

Operating instructions

Diffuse reflection sensor with

background suppression

OGH7xx

704076 / 03 06 / 2011

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure.

Visible laser light; CLASS 1 LASER PRODUCT.

IEC 60825-1 : 2007

Complies with 21 CFR 1040.10 except for deviations pursuant to Laser

Notice No. 50, dated June 2007.

Position of the product label Additional label

3 Functions and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range 20 ... 200 mm (on white paper 200 x 200 mm, 90 % remission)

4 Installation



1: LED

2: programming buttons

►Align the diffuse reflection sensor to the object to be detected.

►Secure it to a bracket.

Note:

The objects to be detected are to move transver-

sally to the lens of the sensor.

►In case of other directions of movement

it should be tested before whether safe

switching is guaranteed.

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of electri-

cal equipment must be adhered to.

►Voltage supply according to EN 50178.

►Disconnect power.

►Connect the unit as follows:

DC PNP











pin 1 = L+ ( 10...36 V DC )

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

DC NPN











pin 1 = L+ ( 10...36 V DC )

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

6 Settings

6.1 The sensor is to switch when the object is detected

►Position the object





►Press [OUT on] for 2 s.

> The sensitivity is set to the object.

> The LED flashes.

►Remove the object





►Press [OUT off].

> The sensitivity is set without object.

> The LED goes out. The programming is finished.

6.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off] for 2 s.

►Remove the object (see figure 2) and press [OUT on].

The setting can also be carried out first without object and then with object.

6.3 Setting of the maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

6.4 Programming unsuccessful

> The LED flashes quickly, 8 Hz.

• Measured value difference too small

• Max. programming time (15 min.) exceeded.

6.5 Electronic lock

Lock or unlock the buttons

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED status.

7 Operation

►Check whether the unit operates correctly.

> The LED lights when the switching output is switched.

8 Maintenance, repair and disposal

►Keep the front pane of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material.

►Do not try to open the module enclosure. There are no user - serviceable

components inside.

Technical data and further information at

www.ifm.com→Selectyourcountry→Datasheetdirect:

Other manuals for Efector 200

Table of contents

Other IFM Electronic Accessories manuals

IFM Electronic

IFM Electronic efector200 OC User manual

IFM Electronic

IFM Electronic Efector 200 OL Series User manual

IFM Electronic

IFM Electronic ID000A User manual

IFM Electronic

IFM Electronic efector 300 SU8001 User manual

IFM Electronic

IFM Electronic Efector 300 User manual

IFM Electronic

IFM Electronic efector 300 SU9001 User manual

IFM Electronic

IFM Electronic Efector 600 TC7430 User manual

IFM Electronic

IFM Electronic Efector 500 PN3 User manual

IFM Electronic

IFM Electronic LR3000 User manual

IFM Electronic

IFM Electronic LK1022 User manual

IFM Electronic

IFM Electronic efector200 O7H2 Series User manual

IFM Electronic

IFM Electronic LR2059 User manual

IFM Electronic

IFM Electronic efector200 OG Series User manual

IFM Electronic

IFM Electronic TUV NORD Efector 110 GM701S User manual

IFM Electronic

IFM Electronic efector150 User manual

IFM Electronic

IFM Electronic Efector 100 User manual

IFM Electronic

IFM Electronic VNB001 User manual

IFM Electronic

IFM Electronic LR2759 User manual

IFM Electronic

IFM Electronic LR8300 User manual

IFM Electronic

IFM Electronic Efector 150 KNM User manual

IFM Electronic

IFM Electronic Efector 200 Installation guide

IFM Electronic

IFM Electronic LR3000 User manual

IFM Electronic

IFM Electronic EFECTOR 500 PI26 User manual

IFM Electronic

IFM Electronic efector200 OT Series User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit instruction manual