IFM Electronic Efector150 User manual

Operating instructions

(Ex protection related part) for capacitive sensors

according to EU directive 94/9/EC annex VIII (ATEX)

group II, equipment category 3D

KI5**A / KI0**A

706246 / 00 10 / 2012

UK

2

Remarks for safe use in hazardous areas

Functions and features

• Use in hazardous areas according to the classification

II 3D

(group II, category 3D, apparatus for dust atmosphere).

Complies with the requirements of the standards EN 60079-0 and EN 60079-31.

• Marking

II 3D Ex tc IIIC T90°C Dc X IP65/67

• Permissible operating temperature of the application (proper usage):

Ta: -20°C...+60°C

Installation / Set-up

The units must only be installed, connected and set up by qualified staff. The qualified staff

must have knowledge of protection classes, regulations and provisions for apparatus in

hazardous areas.

Check whether the classification (see "Marking" above and marking on the unit) is suitable

for the application.

Installation remarks / Installation

• Adhere to the relevant national regulations and provisions.

• The relevant installation regulations must be adhered to. In particular, take into account the

requirements relating to the temperature limitation as regards the expected dust deposits.

• Avoid electrostatic charging on housings and cables.

• To avoid electrostatic charging steps must be taken to ensure the equalisation of potential

of metal parts (plug housing, fixing elements, etc.).

• Protect the units and the cables efficiently against damage.

• To avoid soiling, do not remove the dust caps from the cable glands or the plugs until

introducing the cables or attaching the socket.

• After the electrical connection has been made fully insert the terminal chamber onto

the sensor and tighten the nut onto the terminal chamber using a spanner (a/f 36 mm)

(tightening torque min. 10 Nm).

• Maintenance intervals are application-specific and therefore need to be defined by the

operator depending on the operating conditions.

• During maintenance, especially those parts on which the type of protection depends need

to be examined (e.g. integrity of the components of the cable gland, of the seals).

3

UK

Special conditions for safe operation

• For units with terminal chamber (cable gland) and cable units a sufficient strain relief must

be ensured or the cable must be firmly laid.

• Do not disconnect the cables from units with terminal chamber while live.

• The housing and housing parts made of plastic were tested in accordance with

EN 60079-0 for group II and for a low mechanical risk with an impact energy of 4 joules.

• Avoid direct radiation with high UV components (sunlight). Mount the unit in a protected

place.

• Where units require an additional fuse, this must be located outside the hazardous areas.

Maintenance / repair

The unit must not be modified nor can it be repaired. In case of a fault please contact the

manufacturer.

Data sheets, EC declaration of conformity and EC type test certificates are available from

the manufacturer on request.

Other manuals for efector150

3

Table of contents

Other IFM Electronic Accessories manuals

IFM Electronic

IFM Electronic Efector 300 SM7050 User manual

IFM Electronic

IFM Electronic Ecomat 100 CR2102 Application guide

IFM Electronic

IFM Electronic ID000A User manual

IFM Electronic

IFM Electronic Efector160 LK3 User manual

IFM Electronic

IFM Electronic efector 200 OT User manual

IFM Electronic

IFM Electronic LK7 User manual

IFM Electronic

IFM Electronic PI209 Series User manual

IFM Electronic

IFM Electronic efector100 GG507S User manual

IFM Electronic

IFM Electronic efector200 OT Series User manual

IFM Electronic

IFM Electronic Efector 200 User manual

IFM Electronic

IFM Electronic efector 200 OPU200 User manual

IFM Electronic

IFM Electronic VKV021 User manual

IFM Electronic

IFM Electronic PI7093 User manual

IFM Electronic

IFM Electronic VNB001 User manual

IFM Electronic

IFM Electronic EFECTOR200 OC Series User manual

IFM Electronic

IFM Electronic efector 300 SU8200 User manual

IFM Electronic

IFM Electronic efector 300 SM0505 User manual

IFM Electronic

IFM Electronic efector200 OW Series User manual

IFM Electronic

IFM Electronic Efector 500 PL2058 User manual

IFM Electronic

IFM Electronic efector150 User manual

IFM Electronic

IFM Electronic ecomat100 CR2101 Application guide

IFM Electronic

IFM Electronic efector160 LI214 Series User manual

IFM Electronic

IFM Electronic efector 300 SU8001 User manual

IFM Electronic

IFM Electronic efector100 GG507S User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit instruction manual