IFM Electronic ID000A User manual

704727 / 00 07 / 2010

UK

Operating instructions

Inductive sensors

ID000A / ID500A

2

Operating instructions (safety-related part ATEX)

Remarks for safe use in hazardous areas

Functions and features

• Use in hazardous areas according to the classification

II 3D

(group II, category 3D, apparatus for dust atmosphere).

The requirements of the standards EN 61241-1 and EN 61241-0 are met.

Shock test to EN 60947-5-2 with 0.5 joules.

• Marking

II 3D Ex tD A22 IP65 T90°C X Ta: -20...60°C ID000A / ID500A

Installation / Set-up

The units must only be installed, connected and set up by qualified staff. The qualified staff

must have knowledge of protection classes, regulations and provisions for apparatus in

hazardous areas.

Check whether the classification (see "Marking" above and marking on the unit) is suitable

for the application.

Installation remarks / Installation

• Adhere to the relevant national regulations and provisions.

• The relevant installation regulations must be adhered to.

• Avoid electrostatic charging on housings and cables.

• To avoid electrostatic charging steps must be taken to ensure the equalisation of potential

of metal parts (plug housing, fixing elements, etc.).

• Protect the units and the cables efficiently against damage.

• To avoid soiling, do not remove the dust caps from the cable glands until introducing the

cables.

• For units with cable gland: To ensure the required minimum protection, the clamping screw

of the cable gland must be firmly tightened (see technical data sheet for tightening torque).

• Maintenance intervals are application-specific and therefore need to be defined by the

operator depending on the operating conditions.

• During maintenance, especially those parts on which the type of protection depends need

to be examined (e.g. integrity of the components of the cable gland, of the seals).

3

UK

Special conditions for safe operation

• For units with terminal chamber (cable gland) and cable units a sufficient strain relief must

be ensured or the cable must be firmly laid.

• For test purposes, the housing and housing parts made of plastic were exposed to

mechanical stress of 0.5 joules (in accordance with EN 60947-5-2). The user must take

appropriate measures (e.g. installation conditions, use of a protective device, etc.) to

ensure that the units are not exposed to major mechanical stress/shocks.

• Avoid direct radiation with high UV components (sunlight). Mount the unit in a protected

place.

• Units of the type ID must be mounted on a flat surface and the entire bottom must lie

flat on the surface. When mounted with the ifm mounting sets E11121 or E11122, these

requirements are met.

Maintenance / Repair

The unit must not be modified nor can it be repaired. In case of a fault please contact the

manufacturer.

Data sheets and EC declaration of conformity are available from the manufacturer on

request.

This manual suits for next models

1

Table of contents

Other IFM Electronic Accessories manuals

IFM Electronic

IFM Electronic VNB001 User manual

IFM Electronic

IFM Electronic efectro 500 User manual

IFM Electronic

IFM Electronic Efector 150 KNM User manual

IFM Electronic

IFM Electronic LR3000 User manual

IFM Electronic

IFM Electronic O1D100 User manual

IFM Electronic

IFM Electronic O5E5 A Series User manual

IFM Electronic

IFM Electronic efector200 OJ User manual

IFM Electronic

IFM Electronic GM701S User manual

IFM Electronic

IFM Electronic efector 250 User manual

IFM Electronic

IFM Electronic efector 500 PI00 A Series User manual

IFM Electronic

IFM Electronic efector180 IX5010 User manual

IFM Electronic

IFM Electronic efector 300 SU8200 User manual

IFM Electronic

IFM Electronic LK1022 User manual

IFM Electronic

IFM Electronic efector 300 SU7000 User manual

IFM Electronic

IFM Electronic efector 800 VSE100 User manual

IFM Electronic

IFM Electronic EFECTOR 600 TW2000 User manual

IFM Electronic

IFM Electronic SB 4 Series User manual

IFM Electronic

IFM Electronic O1D155 User manual

IFM Electronic

IFM Electronic efector200 OT Series User manual

IFM Electronic

IFM Electronic SM6000 User manual

IFM Electronic

IFM Electronic efector 300 SM0505 User manual

IFM Electronic

IFM Electronic efector 500 PM2055 User manual

IFM Electronic

IFM Electronic PI209 Series User manual

IFM Electronic

IFM Electronic efector 300 SU9004 User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit instruction manual