ICP DAS USA M-7016 User manual

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7016

2-channel Strain Gauge Voltage Input &

Current Input Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7016d

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7016 supports full-bridge strain gauges and provides 2 Analog Input channels, 1

excitation voltage output channel, 1 Digital Input channels and 4 Digital Output channels.

The module provides a programmable input range (±15 mV, ±50 mV, ±100 mV, ±500

mV, ±1 V, and ±2.5 V) and each Analog Input channel can be individually configured.

Excitation voltage output can be in the range of 0 ~ +10 V, with a 40 mA driving

efficiency. Digital Output channels can also be set as high or low alarm outputs. The M-

7016 supports both the Modbus RTU and DCON protocols, which can be configured via

software, and all hardware specifications are the same as the I-7016.

2. Terminal Assignment

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default setting for M-7016/16D/16P/16PD :

•z Address : 01

•z Analog Input Type : Type 05, -2.5 to +2.5 V

•z Baudrate : 9600 bps

•z Checksum disable, engineer unit format, 60Hz filter

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

Sub-function 04h of Function 46h, see user manual Section 3.3.2

Sub-function 06h of Function 46h, see user manual Section 3.3.4

Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.

M-7016 2-ch Strain Gauge Voltage & Current Input DAQ Module - QuickStart (May/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Table of contents

Other ICP DAS USA Control Unit manuals

ICP DAS USA

ICP DAS USA M-7033 User manual

ICP DAS USA

ICP DAS USA I-7016D User manual

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O User manual

ICP DAS USA

ICP DAS USA 7188EN Installation guide

ICP DAS USA

ICP DAS USA M-7064 User manual

ICP DAS USA

ICP DAS USA LP-8 21 Series User manual

ICP DAS USA

ICP DAS USA ZT-257 Series User manual

ICP DAS USA

ICP DAS USA MDC-700 Series User manual

ICP DAS USA

ICP DAS USA iWSN-110X Series User manual

ICP DAS USA

ICP DAS USA tSH-725 User manual

ICP DAS USA

ICP DAS USA ET-87P2 User manual

ICP DAS USA

ICP DAS USA WF-2026 User manual

ICP DAS USA

ICP DAS USA M-7051 User manual

ICP DAS USA

ICP DAS USA I-8123W Setup guide

ICP DAS USA

ICP DAS USA LinPAC-51 Series User manual

ICP DAS USA

ICP DAS USA tSH-700 Series User manual

ICP DAS USA

ICP DAS USA GT-540P-3GWA-OEM1 User manual

ICP DAS USA

ICP DAS USA tET Series User manual

ICP DAS USA

ICP DAS USA SG-3784M User manual

ICP DAS USA

ICP DAS USA M-7002 User manual

ICP DAS USA

ICP DAS USA XP-8000-Atom-CE6 User manual

ICP DAS USA

ICP DAS USA DS-2200 Series User manual

ICP DAS USA

ICP DAS USA I-7055D User manual

ICP DAS USA

ICP DAS USA I-7016 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual