ICP DAS USA M-7026 User manual



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1



M-7026

6-ch Analog Input, 2-ch Analog Output, 3-ch

Digital Input and 3-ch Digital Output Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7026.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7026 is a Modbus RTU based multifunction module with 6 analog inputs, 2

analog outputs, 3 digital inputs, and 3 digital outputs . It provides a programmable input

range on all analog inputs (+/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V, +/-20 mA or 0

~ +20 mA). The analog outputs are 12-bit at +/-5 V, +/-10 V, 0 ~ +20 mA or +4 ~ +20

mA. All digital outputs can be set as alarm outputs. Each analog input can be

configured for an individual range and provides a high overvoltage protection of 240

Vrms. Voltage and current inputs/outputs are jumper selectable.

2. Terminal Assignment



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2



3. Block/ Wiring Diagram



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3



4. Default Settings

The default settings for the M-7026 are:

・ Module Address: 01

・ Analog Input Type: Type 08, -10 V to +10 V

・ Analog Output Type: Type 3, -10 V to +10 V

・ Protocol: Modbus RTU

・ Baud Rate: 9600 bps

・ Checksum disabled

・ Engineering Units format

・ Filter set at 60 Hz rejection



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5



5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6



4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7



5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8



7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

・ Sub-function 04h of Function 46h, see user manual Section 3.3.2

・ Sub-function 06h of Function 46h, see user manual Section 3.3.4

・ Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

9



8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.



Other manuals for M-7026

Table of contents

Other ICP DAS USA Control Unit manuals

ICP DAS USA

ICP DAS USA M-7064 User manual

ICP DAS USA

ICP DAS USA DS-2200 Series User manual

ICP DAS USA

ICP DAS USA tPET-P2R2 User manual

ICP DAS USA

ICP DAS USA M-7024 User manual

ICP DAS USA

ICP DAS USA tSH-700 Series User manual

ICP DAS USA

ICP DAS USA tET-P2A2 User manual

ICP DAS USA

ICP DAS USA iWSN-110X Series User manual

ICP DAS USA

ICP DAS USA I-7080 User manual

ICP DAS USA

ICP DAS USA PM-3133i User manual

ICP DAS USA

ICP DAS USA LP-8 4 Series General instructions

ICP DAS USA

ICP DAS USA WISE-5801-MTCP User manual

ICP DAS USA

ICP DAS USA I-7063D User manual

ICP DAS USA

ICP DAS USA tM-AD5 User manual

ICP DAS USA

ICP DAS USA LP-8 21 Series User manual

ICP DAS USA

ICP DAS USA M-7002 User manual

ICP DAS USA

ICP DAS USA M-7041 User manual

ICP DAS USA

ICP DAS USA I-8094 Parts list manual

ICP DAS USA

ICP DAS USA M-7017R User manual

ICP DAS USA

ICP DAS USA M-7041D User manual

ICP DAS USA

ICP DAS USA I-8026W User manual

ICP DAS USA

ICP DAS USA I-8092F Parts list manual

ICP DAS USA

ICP DAS USA I-7083 User manual

ICP DAS USA

ICP DAS USA M-7033D User manual

ICP DAS USA

ICP DAS USA M-7033 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual