ICP DAS USA EIP-2000 Series Installation guide
ICP DAS
EIP-2000 FAQ
FAQ Version 1.5
ICP DAS Co., Ltd.
2022-12-01
2
Table of Contents
Q1：How to connect to the Allen-Bradley PLC？ ................................................................................................ 3
Q2：How to use EDS file of EIP-2000 series？ .................................................................................................. 7
Q3: When I click the “Network Scan” button, and it pop-up a “Can not find any module” window. What should I
do?.................................................................................................................................................................... 11
Q4: The AI status we get from the EIP-2017/EIP-2019 is different with the real AI value. How do I solve this
problem? ........................................................................................................................................................... 11
Q5: If I forget the IP address of the EIP-2000 modules, how do I search them? ................................................ 12
Q6: I can't update the firmware with the Utility, how should I do? ...................................................................... 12
Q7: How to know the version of EIP-2000 modules hardware? ......................................................................... 12
Q8: How to find the compatible FW for EIP-2000 modules? .............................................................................. 13
Q9: Is there any LabVIEW sample to EIP-2000 modules? ................................................................................ 13
Q10: What is an EDS file? ................................................................................................................................ 14
Q11: Where can I download the EDS file of EIP-2000? ..................................................................................... 14
Q12: What is the Instance ID of EIP-2000 series? ............................................................................................ 14
Q13: What is the data length of the EIP-2000 series? ....................................................................................... 14
Q14: I can ping the EIP-2000 module, but I cannot use the EIP-2000 Utility for setting and communication
testing. How to solve this problem? ................................................................................................................... 15
Q15: If I forget the network settings of the EIP-2000 module, besides restoring the original factory settings, is
there any other solution? ................................................................................................................................... 17
Q16: When I cannot use the EIP-2000 Utility to scan the button, how can I configure or test the connection of
the EIP-2000 module? ...................................................................................................................................... 18
Q17: I can’t measure the current value when I change EIP-2017 to the Single-Ended mode. What can I do? .. 18
3
Q1：How to connect to the Allen-Bradley PLC？
A1：It is tested and confirmed that the EIP-2000 can be connected to the Allen-BradleyTM ControlLogix
Logix 5563 through the 1756-ENBT ControlLogix EtherNet/IP Module successfully. The configuration
software is RSLogix 5000. Please follow the steps below:
1.
Open RSLogix 5000 and create a new project.
Figure1-1. Create a new project.
2.
Select the PLC type and give the project a name.
Figure1-2. Set the PLC type and project name.
4
3.
Create a new module in the “Ethernet” item.
Figure 1-3. Create a new module.
4.
Select the “ETHERNET-MODULE” below “Communications” in the Select Module window.
5
Figure1-4. Select “ETHERNET-MODULE”.
5.
Configure the new module parameters. The I/O length of new module must be the same with the
length of EIP-2000 I/O data. The data assembly please refer to Table 1-1 and the instance ID
please refer to Table 1-2.
Figure1-5. The settings of EIP-2055
Table 1-1. Data Assembly of EIP-2000
Module
Data Assembly Byte
count
Description
EIP-2055
Input Assembly
34
1st Byte: DI status
2nd Byte: DO status read back
3rd~34th Byte: DI counters
Output
Assembly
2
1st Byte: DO status
2nd Byte: to set DI counters zero
EIP-2060
Input Assembly
26
1st Byte: DI status
2nd Byte: DO status read back
3rd~26th Byte: DI counters
Output
Assembly
2
1st Byte: DO status
2nd Byte: to set DI counters zero
EIP-2042
Input Assembly
2
1st Byte: DO status read back (DO0~DO7).
2nd Byte: DO status read back (DO8~DO15).
Output
Assembly
2
1st Byte: DO status (DO0~DO7).
2nd Byte: DO status (DO8~DO15).
6
EIP-2051
Input Assembly
66
1st Byte: DI status(DI0~DI7).
2nd Byte: DI status(DI8~DI15).
3rd~65th Byte: DI counters.
Output
Assembly
2
1st Byte: to set DI counters zero (DI0~DI7).
2nd Byte: to set DI counters zero (DI8~DI15).
EIP-2017
Input Assembly
31
1st ~ 16th Byte: AI status(AI0~7) for DIFF. or S.E.
mode.
17nd ~ 31th Byte: AI status(AI8~15) for S.E. mode
only.
Output
Assembly
22
1st Byte: Set value to the module.
2nd ~ 17th Byte: Set type code to AI0~AI15.
18th Byte: Filter selection of AI
19th Byte: Channel mode selection DIFF. or S.E.
20th Byte: AI representation
21th Byte: AI channel selection (AI0 ~ AI7)
22th Byte: AI channel selection (AI8 ~ AI15)
EIP-2019
Input Assembly
20
1st ~ 16th Byte: AI status(AI0~AI7).
17nd ~ 18th Byte: The Brocken wire status.
19rd ~ 20th Byte: CJC status.
Output
Assembly
21
1st Byte: Set value to the module.
2nd ~ 7th Byte: Set type code to Ch0~Ch7.
8th Byte: Filter selection of AI
9th Byte: Wire break detector
10th Byte: AI representation
11th Byte: Select AI channel to be short
12th Byte: CJC switch
13th Byte: CJC increment
14th ~ 21th Byte:CJC Offset
Table 1-2. Instance ID table of EIP-2000
Implicit Message Information of EIP-2000
Instance Instance ID Data length
Input(T->O) 65hex(101) Depends on modules.
e.g.34(EIP-2055)
Out(O->T) 66hex(102) Depends on modules.
e.g.2(EIP-2055)
Configuration 64hex(100)
7
Q2：How to use EDS file of EIP-2000 series？
A2：EDS file is a convenient way to make the connection between EtherNet/IP Scanner and Adapter.
All the EIP-2000 series EDS file can be download on our website:
http://www.icpdas.com/products/Remote_IO/can_bus/EtherNet_IP_series.htm
We provide the connection steps of Hilscher CIFX 50-RE with EIP-2055 EDS file. The configuration
software is SYNCON.net. Please refer to the steps below：
1.
Open SYNCON.net and create a new project.
Figure2-1 Create a new project.
2.
To find the “CIFX RE/EIM” item below “EtherNet/IP -> Master”, and drag the “CIFX RE/EIM” to the
busline.
Figure2-2 Select CIFX RE/EIM
8
3.
Click “Network” and select “Import Device Descriptions”.
Figure2-3 Import Device Descriptions
4.
To select the EDS file you download on our website of CD.
Figure2-4 Select EDS file
5.
To find the “EIP-2055 EDS V1.1” item below “EtherNet/IP -> Slave”, and drag the “EIP-2055 EDS
V1.1” to the busline.
Figure2-5 EIP-2055 EDS
9
6.
To configure CIFX RE/EIM and EIP-2055 in the same network area.
Figure2-6 Network Settings
7.
Right click the CIFX_RE/EIM and click “Download”.
Figure2-7 Download configurations.
10
8.
Right click the CIFX_RE/EIM again and click “Start Communication”.
Figure2-8 Start Communication
9.
The communication is complete. You can observe the I/O status on the Diagnostic window.
Figure2-9 I/O status observation
Other manuals for EIP-2000 Series
2
Table of contents
Other ICP DAS USA Control Unit manuals
ICP DAS USA
ICP DAS USA MN-3253 Series User manual
ICP DAS USA
ICP DAS USA PROFI-5045 User manual
ICP DAS USA
ICP DAS USA ZT-2055 User manual
ICP DAS USA
ICP DAS USA I-7016 User manual
ICP DAS USA
ICP DAS USA ET-2260 User manual
ICP DAS USA
ICP DAS USA ET-7065 User manual
ICP DAS USA
ICP DAS USA MDC-700 Series User manual
ICP DAS USA
ICP DAS USA ET-2260 User manual
ICP DAS USA
ICP DAS USA tPET-P2R2 User manual
ICP DAS USA
ICP DAS USA M-7033 User manual
ICP DAS USA
ICP DAS USA SG-3227 User manual
ICP DAS USA
ICP DAS USA ET-7H16M Series User manual
ICP DAS USA
ICP DAS USA DS-700 Series User manual
ICP DAS USA
ICP DAS USA I-7060D User manual
ICP DAS USA
ICP DAS USA M-7051 User manual
ICP DAS USA
ICP DAS USA PETL-7060 User manual
ICP DAS USA
ICP DAS USA tET Series User manual
ICP DAS USA
ICP DAS USA I-8092F Parts list manual
ICP DAS USA
ICP DAS USA PROFIBUS PROFI-2510 User manual
ICP DAS USA
ICP DAS USA ZT-2570 User manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
