IBM Aptiva 2190 Owner's manual
.
Hardware Maintenance Service
for Service Level A
Aptiva Type 2190
2190
.
First Edition (September 1999)
The following paragraph does not apply to any state or country where such
provisions are inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. References to IBM products, programs, or
services do not imply that IBM intends to make them available outside the
United States. This publication could include technical inaccuracies or
typographical errors. Changes are periodically made to the information herein;
these changes will be made in later editions. IBM may make improvements
and/or changes in the product(s) and/or the program(s) at any time. Address
comments about this publication to IBM Corporation, Dept. E23/962-2, 455
Park Place, Lexington, KY 40511-1856, USA. Information you supply may be
used by IBM without obligation. For copies of publications related to this
product, call toll free 1-800-IBM-7282 in the Continental U.S.A. In Canada,
call toll free 1-800-465-7999.
© Copyright International Business Machines Corporation 1999.
All rights reserved.
Note to U.S. Government Users – Documentation related to restricted rights –
Use, duplication or disclosure is subject to restrictions set forth in GSA ADP
Schedule Contract with IBM Corp.
Copyright IBM Corp. 1999 I
Contents
Notices ..................................................................................................... IV
Voltage Supply Switch Settings ..................................................................IV
Safety Information.......................................................................................V
Laser Compliance Statement............................................................... XXXIV
Trademarks ......................................................................................... XXXV
Preface............................................................................................... XXXVI
General Information................................................................................1-1
Introduction...............................................................................................1-2
Product Overview......................................................................................1-2
Hardware Interfaces..................................................................................1-6
CMOS Reset.............................................................................................1-8
Flash (BIOS) Update Procedure................................................................1-9
BIOS-contained Model Number and Serial Number..................................1-10
BIOS Setup Utility...................................................................................1-11
Working with the Setup Menus...........................................................1-11
Start Options.....................................................................................1-13
Advanced Setup................................................................................1-16
Plug and Play control.........................................................................1-17
Power Management Setup.................................................................1-19
ISA Legacy Resource........................................................................1-20
PC Health Status...............................................................................1-20
Set Password....................................................................................1-20
Specifications..........................................................................................1-22
Operating Requirements .........................................................................1-23
Special Tools..........................................................................................1-24
Check Procedures...................................................................................2-1
Introduction...............................................................................................2-2
Start .........................................................................................................2-3
Index of Symptoms, Messages, Error Codes, or Beeps..............................2-8
Troubleshooting......................................................................................2-23
Factory-Installed Storage Devices......................................................2-24
Factory-Installed Modem Card ...........................................................2-26
Audio (Not Supported by Diagnostics Program)..................................2-28
CD-ROM Drive ..................................................................................2-30
Memory.............................................................................................2-31
Keyboard...........................................................................................2-32
Mouse...............................................................................................2-33
Power Supply....................................................................................2-35
II
Monitor..............................................................................................2-38
Undetermined Problems ....................................................................2-40
Diagnostic Aids.......................................................................................3-1
Introduction...............................................................................................3-2
Power-On Self Test...................................................................................3-2
Diagnostics Tools......................................................................................3-3
Using Diagnostics Program from Recovery CD.....................................3-3
Diagnostics Program Features.............................................................3-4
Repairing Information............................................................................4-1
Removals and Replacements....................................................................4-2
Identifying the Parts of the System Unit.................................................4-3
Top Cover............................................................................................4-5
Adapter Cards .....................................................................................4-6
Diskette Drive ......................................................................................4-8
CD-ROM Drive.....................................................................................4-9
Hard Disk Drive..................................................................................4-10
System Board ...................................................................................4-11
Power Supply ....................................................................................4-13
Memory (DIMM).................................................................................4-14
Parts/Test Point Locations......................................................................5-1
Introduction...............................................................................................5-2
Aptiva Type 2190 System Board Layout ....................................................5-3
2190 System Board Jumper Settings....................................................5-4
2190 Processor Type Jumper Settings.................................................5-5
2190 System Board Connectors and Functions.....................................5-6
Power Supply Cable Connector Specifications...........................................5-7
Main Output Pin Assignment................................................................5-8
Factory-Installed Modem Card Layout......................................................5-10
Factory-Installed Modem Card Connector Functions...........................5-10
3.5-In. Hard Disk Drive Jumper Locations & Settings................................5-11
CD-ROM Drive........................................................................................5-12
CD-ROM Drive Rear Panel Connectors and Features.........................5-13
CD-ROM Drive Jumper Settings.........................................................5-13
DIMM Configurations...............................................................................5-14
System Board Connector Pin Signals ......................................................5-14
Monitor Port Signals ..........................................................................5-14
Serial Port Signals.............................................................................5-14
Parallel Port Signals ..........................................................................5-15
Mouse Port Signals............................................................................5-15
Keyboard Port Signals.......................................................................5-15
Diskette Drive Cable Connector Signals.............................................5-16
IDE Cable Connector Signals.............................................................5-17
III
Safety Inspection Guide..........................................................................6-1
General Guidelines ...................................................................................6-2
Parts Catalog...........................................................................................7-1
Assembly 1 : Aptiva Type 2190 System Unit..............................................7-2
Assembly 2 : Aptiva Type 2190 Diskette Drive, Hard Disk Drive..................7-5
Assembly 3 : Aptiva Type 2190 CD-ROM, Modem Card.............................7-6
Assembly 4 : Aptiva Type 2190 Keyboard and Mouse................................7-7
Appendix A. FRU Number Index
Appendix B. Online Support Information
Index
IV
Notices
References in this publication to IBM products, programs, or services do not
imply that IBM intends to make these available in all countries in which IBM
operates. Any reference to an IBM product, program, or service is not
intended to state or imply that only IBM’s product, program, or service may be
used. Any functionally equivalent product, program, or service that does not
infringe any of IBM’s intellectual property rights, or other legally protectable
rights, may be used instead of the IBM product, program, or service.
References in this publication to IBM products, programs, or services are
purely hardware-related and do not cover circumstances of software
problems. Evaluation and verification of operation in conjunction with other
products, program, or services, except those expressly designated by IBM are
the user’s responsibility.
IBM may have patents or pending patent applications covering subject matter
in this document. The featuring of these patents, pending or otherwise, in this
document does not give you any license to these patents. You can send
license inquires, in writing, to the IBM director of Commercial Relations, IBM
Corporation, Purchase, NY10577.
Voltage Supply Switch Settings
Your IBM Aptiva Personal Computer might have voltage switches, which must
be set correctly for your voltage supply. If your monitor or system unit has a
voltage switch, complete these steps to make sure each switch is set
correctly:
1. Determine the correct voltage switch setting for your area:
Voltage Supply Range Voltage Switch Setting
100-127 V 110 V
200-240 V 220 V
2. Locate the voltage switch on the back of your monitor or system unit. If the
setting shown on the switch is:
qCorrect: start setting up your IBM Aptiva computer.
qIncorrect: change the voltage switch setting.
V
Safety Information
DANGER
To avoid a shock hazard, do not connect or disconnect any cables or
perform installation, maintenance, or reconfiguration of this product
during an electrical storm.
To avoid shock hazard:
qThe power cord must be connected to a properly wired and earthed
receptacle.
qAny equipment to which this product will be attached must also be
connected to properly wired receptacles.
When possible, use one hand to connect or disconnect signal cables to
prevent a possible shock from touching two surfaces with different
electrical potentials.
Electrical current from power, telephone, and communications cables is
hazardous. To avoid shock hazard, connect and disconnect cables as
described following when installing, moving, or opening covers of this
product or attached devices.
VI
To Connect To Disconnect
1. Turn Everything OFF. 1. Turn Everything OFF.
2. First, attach all cables to devices. 2. First, remove power cord(s) from
outlet
3. Attach signal cables to receptacles. 3. Remove signal cables from
receptacles.
4. Attach power cord(s) to outlet. 4. Remove all cables from devices.
5. Turn device ON
Table of contents
Other IBM Desktop manuals
IBM
IBM 8841 - eServer xSeries 236 User manual
IBM
IBM 300 Series 6268 Owner's manual
IBM
IBM PC 300 User manual
IBM
IBM PC 300 Manual
IBM
IBM ThinkCentre 9212 User manual
IBM
IBM NetVista A20 User manual
IBM
IBM NetVista A30 User manual
IBM
IBM NetVista A22p User manual
IBM
IBM System/370 User manual
IBM
IBM 5110 Reference manual
IBM
IBM PCjr Owner's manual
IBM
IBM PC 300PL Types 6862 User manual
IBM
IBM 5100 Use and care manual
IBM
IBM X40i - NetVista - 2179 User manual
IBM
IBM NetVista A40 Setup guide
IBM
IBM 5110 Setup guide
IBM
IBM NetVista X40 Mounting instructions
IBM
IBM NetVista Technical document
IBM
IBM NetVista X40 User manual
IBM
IBM Aptiva 2140 Owner's manual
