I3 International Ax45RM series User manual

Ax45RM/65RM-series

User Manual

Before attempting to connect or operate this product, read these instructions carefully.

Save this manual for future use.

CONTENTS

1. Warnings and operation notes..................................3

2. Unpacking................................................................5

3. Dimensions & Parts Identification...........................6

4. Installation...............................................................7

5. Connecting to the SRX-Pro Server.........................16

6. Advanced Camera Setup.........................................21

7. Specifications.....................................................54

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107

Ax45RM/65RM-series User Manual

No part of this manual may be reproduced or transmitted in any form or by any means,

electronic or mechanical, including but not limited to, photocopying, recording, or by

any information storage or retrieval system, without the prior written permission of the

Annexxus is a registered trademark of i3 International Inc.

Disclaimer

This quick start guide is provided as is, without warranty of any kind, expressed or

implied, including but not limited to performance, merchantability, or fitness for any

particular purpose. Neither i3 International Inc. nor its dealers or distributors shall be

liable to any person or entity with respect to any liability, loss, or damage, caused or

alleged to have been caused directly or indirectly by this information.

Furthermore, i3 International Inc. reserves the right to revise this publication, and to

make changes to the content at any time, without notice.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Address:

i3 International Inc.

780 Birchmount Road, Unit 16

Scarborough, ON M1K 5H4

Canada

Tech Support: 1.877.877.7241

Email: [email protected]

Web Site: www.i3international.com

3Rev. 161107

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd

1. Warnings and operation notes

Please read this guide carefully before you install the camera.

Keep this guide for future reference.

Thank you for purchasing an i3 Ax45RM/65RM-series IR Outdoor Dome Camera w/

Motorized Lens. If the system needs to be modified or repaired, contact a certified i3

International Dealer/Installer. When serviced by unauthorized technician, the system

warranty will be voided. Should you have any problems or questions regarding our

products, contact your local i3 International Dealer/Installer.

WARNING! To reduce the risk of fire or electric shock, do not

expose the product to rain or moisture.

Camera’s default IP address is 192.0.0.16

Camera’s default Subnet mask address is 255.255.255.0.

Default camera User Name: i3admin and default Password: i3admin

1.1 Precautions

Installation and servicing should be performed only by qualified and

experienced technicians to conform to all local codes and to maintain your

warranty.

When installing your Ax45RM/65RM camera, be sure to avoid:

• excessive heat, such as direct sunlight or heating appliances

• contaminants such as dust and smoke

• strong magnetic fields

• sources of powerful electromagnetic radiation such as radios or TV transmitters

• moisture and humidity

• areas with mechanical vibrations

• fluorescent lamps or objects that reflect light

• unstable light sources as this may cause flickering

• temperatures below -40°C (-40°F) and above 50°C (122°F)

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107

1.2 Power

This camera supports AC 24V and PoE (IEEE 802.3af Class 3). Max. load of 26W on AC

24V, 20W on PoE+ and 11W on PoE.

Incorrect voltage may cause irreparable damage to the video camera and will

effectively void the camera warranty. For PoE power, insert the RJ45 cable into

the RJ45 jack on the camera’s cable. Connect the other end of the RJ45 cable to

a compatible PoE switch/hub/router. Use RJ45 waterproof connector for outdoor

installations (not included).

1.3 Cleaning

• For maximum optical clarity, the camera or lens must remain clean. Use a soft, dry

cloth to remove finger prints and dust from the dome cover.

• Use a blower to remove dust from the lens.

• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a

small quantity of neutral detergent, then wipe dry.

• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may

damage the surface finish.

1.4 Servicing

To avoid electrical shock and to preserve the product warranty, DO NOT disassemble

the camera. Refer servicing to qualified personnel only.

1.5 Routine Maintenance

• The dome bubble is an optical part. Use a soft and dry cloth to remove any

fingerprints and dust.

• Clean the camera housing with a soft and dry cloth. For more stubborn marks, use

a cloth dampened with a small quantity of neutral detergent, then wipe dry.

• CAUTION: Do not use volatile solvents such as alcohol, benzene or

thinners, as they may damage the surface finish.

Please Note: Scan the QR code below or visit www.i3international.com to view and download the full User

Manual for this camera. Also available for download is the AnnexxusConfigurationTool or ACT program

used to locate and configure your cameras with your SRX-Pro software. This program is already installed

in SRX-Pro v3.3.3.69 and higher. Please contact our Technical Support team if you have any questions or

concerns regarding camera installation or you require software services or support. Technical support can

be reached by email at:

[email protected] or by phone toll free 1.877.877.7241.

QR Code to Complete

User Manual / ACT

5Rev. 161107

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd

2. Unpacking

Ensure that the items received match those listed on the order form and the packing

slip. In addition to this manual and a fully assembled camera, the dome camera

packing box includes:

1. Surface Mount template x1.

2. Rubber gasket x1. Use in all outdoor surface installations in combination with

surface Mount Template.

3. Security torx bit x1.

4. Flush Mount template x1.

5. Round Head Screw (Tapping Type) with O-ring x4.

6. Plastic Anchor x4.

7. 3-ft netowrk cable x1.

8. Long Machine Type screws x3 for flush mounting with back box installations.

9. Standard Rj45 connector x2.

*Note: Based on installation location and surface type, supplied screws and anchors

may not be adequate. Mounting hardware is site-specific and may need to be supplied

by the installer.

2.1 Accessories (not to scale)

Lens Direction

GUIDE PATTERN

CAMERA OUTLINE

CUT LINE

1234

56 7 8

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107

3. Dimensions & Parts Identification

This dome camera is suitable for both indoor and outdoor installation in commercial

and residential environment. With 3-axis mount support, it provides flexible installation

on a ceiling or wall, even on an angle. The dome camera is a fully integrated enclosure

with a back box, camera and lens.

910 11

147 mm (5¾”)

68 mm (2.67”)

94 mm (3.7”)

158 mm (6¼”)

63 mm (2.5”)

84 mm (3.3”)

63 mm (2.5”)

7Rev. 161107

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd

1. Back box. Camera’s back box comes with six (6) 90% pre-drilled hole dimples

with built-in O-ring. For surface mounting, complete drilling a minimum of two (2)

holes.

2. Camera module / second housing

3. Tilt bracket with locking screw

4. Inner liner / Shroud. Inner liner is attached to the camera module but can be

partially detached for easier lens adjustment.

5. IR board

6. Screws securing the dome bubble housing to camera module (x3, silver)

7. Dome bubble housing / Dome cover

8. Lexan bubble

9. 3/4” Top conduit hole. During installation, sealant must be used to maintain the

IP67 status.

10. 3/4” Side conduit hole. During installation, sealant must be used to maintain the

IP67 status.

11. Six (6) 90% pre-drilled hole dimples with built-in O-ring.

12. Reset/Default pin-hole button. Press for 1 second to reboot the camera. Press for

6 seconds to restore camera settings to factory defaults.

13. microSD Card slot for on-camera edge video storage. (microSD cards up to 64GB

supported, not supplied)

14. Mini USB port. Manufacturer use

only

15. Screws attaching camera module to the back box (x3, silver)

16. Screws to engage locking arms (x2, black)

4. Installation

Ax45RM/65RM camera series can be flush-, wall-, surface-, or T-bar ceiling mounted

without additional mounting accessories/brackets.

Start by marking out and preparing the mounting surface, then attach the supplied

mounting template to the mounting surface. Use the appropriate brackets and

equipment to mount the camera. Use supplied rubber gasket in all outdoor surface

installations to provide the seal between the mounting surface and the camera base.

Depending on the type of installation, additional mounting accessories may need to be

purchased.

After installing the camera, your network camera must be accessible from your local

network (LAN).

Optional Mounting Accessories:

• DB60 (Goose Neck Wall Bracket 3/4” NTP). Together with the optional DB60CPM

bracket, DB60 goose neck bracket has the capability of being corner or pole-

mounted.

• DB60CPM (Corner / Pole Mount bracket for DB60)

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107

4.1 Disassembling the Camera

Before mounting and adjusting the camera, follow

these steps to disassemble the camera.

1. Use the provided security Torx bit to loosen

three silver screws securing the dome

bubble housing to camera module (#6). Do

not completely remove the screws from the

dome bubble. Set the dome bubble aside.

2. Use Phillips screwdriver to loosen three

silver screws attaching camera to the

back box (#15)

3. Remove camera’s back box and set aside.

4.2 I/O Connectors (Reserved for future use

Once the camera’s back box has been

removed, Ax45RM/Ax65RM input/output

connectors will be revealed on the

camera’s module, including RJ45 Ethernet/

PoE connector, Audio and Alarm connectors

and AC24V power port.

9Rev. 161107

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd

1. I/O connectors reserved for future use.

2. AC 24V Port. Connect AC 24V power supply.

3. RJ45 Ethernet Connector / PoE. Connect RJ45 network cable for Ethernet/Internet

connectivity. PoE (Power over Ethernet) is supported.

Caution: Do not apply power until the camera is properly and securely mounted.

4. Orange LED. Flashing orange LED indicates data transmission between camera

and the Internet.

5. Green LED. Solid green LED indicates a current live connection.

Reserved Reserved

GND GND AO AI

GNDCOM

4.3 3-Axis lens position adjustment

Pan Adjustment

Rotate the lens base (max 354°) until satisfied with the field of view.

Note: Over-rotation past 354° will cause internal cables to become damaged,

disconnected, or twisted.

Horizontal Rotation

Firmly grasp the camera lens assembly and rotate counter-clockwise / clockwise (max

354°) until satisfied with the field of view.

Note: Over-rotation past 354° will cause internal cables to become damaged,

disconnected, or twisted.

Tilt Adjustment

Tilt the camera lens until satisfied with the field of view.

Once the desired view has been achieved, replace the camera liner until it snaps into

place.

10°~90°

±177°

Pan Adjustment

Horizontal Rotation

Tilt Adjustment

±177°

123

4 5 Reserved Reserved

i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107

Prepare the Mounting Surface:

1. Use the Flush Mounting Template to cut a

hole in the mounting surface.

Disassemble the Camera:

2. Disassemble the camera by removing the

dome bubble. Use the provided security Torx

bit to loosen three silver screws securing the

dome bubble to the camera’s mounting base.

4.4 Flush Mounting w/Locking Arms

Use this installation method for indoor installations only. This method is suitable for

drywall and T-bar installations only. It is possible to flush mount the camera and use

the back box. The Long Machine Type screws provided are used to secure the camera

to the back box through ceiling.

Important. Please Read:

• It is the installer’s responsibility to ensure that the mounting surface is

suitable for the chosen installation method.

• Based on installation location and surface type, supplied screws and

anchors may not be adequate.

• Mounting hardware is site-specific and may need to be supplied by the

installer.

GUIDE PATTERN

CAMERA OUTLINE

CUT LINE

Do not completely remove the screws from the bubble. Lift the dome bubble off

and set aside.

3. Loosen three silver screws attaching camera to the back box. Remove camera’s

back box and set aside. It will not be used in this type of installation.

Back box

not in use

for this

installation

Other manuals for Ax45RM series

This manual suits for next models

Table of contents

Other i3 International Security Camera manuals

i3 International

i3 International Ax63Z Series User manual

i3 International

i3 International Ax63Z Series User manual

i3 International

i3 International Ax52 Series User manual

i3 International

i3 International M77R2 User manual

i3 International

i3 International Ax63C Operating and maintenance instructions

i3 International

i3 International Ax41C1M User manual

i3 International

i3 International Ax47DC User manual

i3 International

i3 International Am73 User manual

i3 International

i3 International Ax40W2 series User manual

i3 International

i3 International Ax65W User manual

i3 International

i3 International Di721 User manual

i3 International

i3 International Ax47R4 User manual

i3 International

i3 International Di721 User manual

i3 International

i3 International Ax61 series User manual

i3 International

i3 International DB78BB User manual

i3 International

i3 International Ax47R series User manual

i3 International

i3 International A 65W Series User manual

i3 International

i3 International Ax46DC User manual

i3 International

i3 International Ax46 Series User manual

i3 International

i3 International Di210 User manual

i3 International

i3 International Ax85 User manual

i3 International

i3 International H59B2 User manual

i3 International

i3 International M71 User manual

i3 International

i3 International Am42 Series User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

i3 International Ax45RM series User manual

Popular Security Camera manuals by other brands