i3 International Ax40W2 series User manual
Ax40W2/4/8-series
User Guide
Before attempting to connect or operate this product, read these instructions carefully.
Save this manual for future use.
CONTENTS
1. Warnings and operation notes..........................................3
2. Unpacking....................................................................5
3. Installation.....................................................................6
4.
Connecting your IP Camera to the SRX-Pro Server.....
....11
5. Advanced Camera Setup..................................................19
6. Specifications.................................................................36
2
i3-TRNG-CAMS-Ax40W.indd Rev. 141126
Ax40W-series User Guide
COPYRIGHT ©2013 by i3 International, Inc. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including but not limited to, photocopying,
recording, or by any information storage or retrieval system, without the prior
written permission of the copyright owner and the publisher.
Annexxus is a registered trademark of i3 International Inc.
Disclaimer
This quick start guide is provided as is, without warranty of any kind, expressed or
implied, including but not limited to performance, merchantability, or fitness for any
particular purpose. Neither i3 International Inc. nor its dealers or distributors shall be
liable to any person or entity with respect to any liability, loss, or damage, caused or
alleged to have been caused directly or indirectly by this information.
Furthermore, i3 International Inc. reserves the right to revise this publication, and to
make changes to the content at any time, without notice.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Address:
i3 International Inc.
780 Birchmount Road, Unit 16
Scarborough, ON M1K 5H4
Canada
Contact us:
Tech Support: 1.877.877.7241
Web Site: www.i3international.com
Table of Contents
1. Warnings and operation notes
2. Product Overview
3. Unpacking
4. Installation
5. Configuration
6. Advanced Camera Setup
7. Specifications
3Rev. 141126i3-TRNG-CAMS-Ax40W.indd
1. Warnings and operation notes
Please read this guide carefully before you install the camera. Keep this
guide for future reference.
Thank you for purchasing an i3 Ax40W-series Mini-dome (Wedge) Fixed camera.
If the system needs to be modified or repaired, contact a certified i3 International
Dealer/Installer. When serviced by unauthorized technician, the system warranty
will be voided. Should you have any problems or questions regarding our products,
contact your local i3 International Dealer/Installer.
1.1 Precautions
Installation and serving should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain
your warranty.
When installing your Ax40W camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• sources of powerful electromagnetic radiation such as radios or TV transmitters
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light
• unstable light sources as this may cause flickering
• temperatures below -10° Celsius or 14° Fahrenheit and above 40° Celsius or
104° Fahrenheit.
WARNING! The use of CSA certified/ UL Listed Class 2 power
adapter is required to ensure compliance.
WARNING! To reduce the risk of fire or electric shock, do not
expose the product to rain or moisture.
4
i3-TRNG-CAMS-Ax40W.indd Rev. 141126
1.2 Power Supply
When using 12VDC, ensure the supplied voltage meets the power consumption
requirements of this camera before powering the camera on. Incorrect voltage may
cause irreparable damage to the video camera and will effectively void the camera
warranty. The camera also comes with the built-in PoE power support.
1.3 Cleaning
• For maximum optical clarity, the camera or lens must remain clean. Use a soft,
dry cloth to remove finger prints and dust from the dome cover.
• Use a blower to remove dust from the lens.
• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened
with a small quantity of neutral detergent, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finish.
1.4 Servicing
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
1.5 Safety Instructions
Equipment to be used in a Network Environment 0 per IEC TR62101. The camera
is to be connected only to PoE network that complies with IEEE 802.3af without
routing to the outside plant.
WARNING! DO NOT connect both PoE and DC12V power connectors
at the same time. For DC power supply use, make sure the polarity is
correct to avoid malfunction and / or camera damage.
5Rev. 141126i3-TRNG-CAMS-Ax40W.indd
2. Unpacking
Check that the items received match those listed on the order form and packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing
box includes:
1. User Manual CD x1
2. Guide Pattern sticker x1
3. 2nd video monitor output BNC cable x1
4. Hex key x1
5. Plastic Anchor x2
6. Round Head Screw (Tapping Type) x2
7. Flat Head Screw (Machine Type 30L) x2
8. Wing (Butterfly) nut x2
9. Washer x2
10. Standard RJ45 Connector x2
11. Desiccant in a package x1
If any parts are missing or damaged, contact the dealer you purchased the camera
from.
Accessories (not to scale)
1
User Guide
IP Finder
2
FRONT
CABLE
90°
0°
270°
180°
54
3
10
67
8 9
11
6
i3-TRNG-CAMS-Ax40W.indd Rev. 141126
3. Installation
Use the appropriate brackets and equipment to mount the camera. After installing
the camera, your network camera should be accessed from your local network.
3.1 Camera Parts
Camera Dome
Camera Body - Side View
Camera Body - Top View
VIDEO OUT
RESET
DEFAULT
VIDEO OUT: Video output connector.
DEFAULT: Press and hold for 5 seconds to return to factory default.
RESET: Press to reboot system.
7Rev. 141126i3-TRNG-CAMS-Ax40W.indd
DC12V
POE/ETHERNET
3.2 Power Connectors
Connect the PoE or DC12V power connector.
PoE (IEEE 802.3af): Connect the RJ-45 connector to a PoE compatible network
device that supplied power through the Ethernet cable.
DC12V: Connect the DC12V power connector to a DC12V power.
WARNING! DO NOT connect both PoE and DC12V power connectors
at the same time. For DC power supply use, make sure the polarity is
correct to avoid malfunction and / or camera damage.
8
i3-TRNG-CAMS-Ax40W.indd Rev. 141126
3.3 Disassembling the Camera
Before you mount and adjust the camera,
follow these steps to disassemble the camera.
1. Using the hex key provided, loosen two
screws on the cover.
2. Remove the dome cover.
3.4 Attaching the Desiccant
1. Take the desiccant out of the package (#11 on Accessories list on page 5)
2. Peel the protective layer revealing the adhesive surface on the desiccant and
attach to the inside of the dome cover as shown in the diagram below.
Peel the
protective layer
on the desiccant
Attach
dessicant to
the inside
of the dome
cover
9Rev. 141126i3-TRNG-CAMS-Ax40W.indd
3.5 Mounting the Camera
Depending on mounting surface, you can use a combination of Plastic Anchors and
Tapping Screws or Machine Type Screws, Wing nuts and Washers.
1. Prepare the mounting surface. Adhere the Mounting Template (#2 on
Accessories list on page 5) to the surface.
2. Drill two screw holes on the mounting surface as well as one round hole
Ø30mm in diameter, according to the template.
3. If installing on solid surface, insert the Plastic Anchors (#6 on Accessories list)
into two holes.
4. Pass all the signal cables through the Ø30mm hole.
5. If installing on solid surface, secure the camera body to the mounting surface
with the Tapping Type Screws (#5 on Accessories list).
If installing on a T-bar ceiling, secure the camera body to the mounting surface
with the Machine Type Screws (#7 on Accessories list) below the mounting
surface and Wing Nut/Washer combo above the mounting surface (#8 & #9 on
Accessories list).
FRONT
CABLE
90°
0°
270°
180°
Ø
30mm
1
2
3
FRONT
CABLE
90°
0°
270°
180°
Ø
30mm
4
3
2
1
SOLID SURFACE MOUNTING T-BAR MOUNTING
10
i3-TRNG-CAMS-Ax40W.indd Rev. 141126
3.6 Adjusting the Camera Position
1. Loosen two screws, as shown in the picture below.
2. Adjust the lens to the desired shooting angle until the required view is achieved
3. Re-tighten the screws once the desired view is achieved.
Loosen two screws
before adjusting the lens
3.7 Completing the Installation
1. Re-attach the dome cover carefully
2. Re-tighten two screws that hold the camera dome cover. This completes the
installation.
Other manuals for Ax40W2 series
1
This manual suits for next models
10
Table of contents
Other i3 International Security Camera manuals
i3 International
i3 International Am42 Series User manual
i3 International
i3 International Ax49D User manual
i3 International
i3 International Ax45RM series User manual
i3 International
i3 International DB78BB User manual
i3 International
i3 International Ax63Z Series User manual
i3 International
i3 International Ax47R series User manual
i3 International
i3 International A 65W Series User manual
i3 International
i3 International Am52RM User manual
i3 International
i3 International Am52 Series User manual
i3 International
i3 International Ax68R User manual
i3 International
i3 International Ax51B User manual
i3 International
i3 International Ax50D User manual
i3 International
i3 International Ax61 series User manual
i3 International
i3 International i3F416U User manual
i3 International
i3 International Ax45RM series User manual
i3 International
i3 International Ax78R User manual
i3 International
i3 International i3R363 User manual
i3 International
i3 International Ax83C User manual
i3 International
i3 International i3-B731 User manual
i3 International
i3 International Ax47R series User manual
