Human Touch HT-9200 Setup guide

X1103

October 17, 2010

REMOVING THE FOOT-AND-CALF MASSAGER

1. Using two people, gently tip the chair onto its side (Fig.1).

2. Use the remote control to deploy the foot-and-calf massager until the connector box becomes

accessible (about 75% full deployment) (Fig.2).

3. Power off the chair, then unplug it.

4. Using a nail clipper or other suitable instrument, cut the zip ties that secure the connector box

to the chair frame (Fig.2).

5. Using a Phillips-head screwdriver, remove the four screws that secure the connector box cover,

then remove the cover (Fig.3).

6. Disconnect the connectors (Fig.4)

7. Using a nail clippers or any other suitable instrument, cut the zip-tie that secures the massager harness

to the frame (Fig.5).

Tools Required: Phillips-head screwdriver, nail clippers or other instrument suitable for cutting zip ties, new zip ties. NOTE: SAVE ALL SCREWS FOR USE DURING REASSEMBLY.

REPLACING THE FOOT-AND-CALF MASSAGER

HT-820/9200

It is imperative that Human Touch® products are repaired in a manner that ensures product safety and regulatory compliance and that is fully consistent with the practices used

during the manufacturing process. Therefore, Human Touch requires that all product repairs are performed using only factory-new parts and in accordance with these repair

instructions. Failure to adhere to these instructions voids the product warranty and releases Human Touch from all liability for injury or product damage resulting from the repair.

SERVICE LEVEL: 3

(Fig.1)

Zip ties (Fig.2)

Connector box

(Fig.3)

Connectors

(Fig.4)

Zip-tie

(Fig.5)

8. Locate the two screws located inside the foot-and-calf massager’s rubber housing and remove them (Fig.6).

9. Using a Phillips-head screwdriver, remove the two screws that secure the fabric strip that holds the rubber housing in place, then remove the fabric strip (Fig.7).

10. Locate the five Phillips-head screws that secure the opposite side of the fabric strip that holds the rubber housing in place, then remove the screws and strip (Fig.8).

11. Using a Phillips-head screwdriver, remove the two screws that secure the two fabric strips that secure the foot-and-calf massager to the frame (Fig.9).

12. Pull the foot-and-calf massager forward to remove it from the chair (Fig.10).

(Fig.6)

Fabric strip

(Fig.7)

(Fig.8) (Fig.9) (Fig.10)

Foot-and-calf massager

Foot-and-calf

massager

INSTALLING THE FOOT-AND-CALF MASSAGER

1. Place the foot and calf massager into position on the frame.

2. Place the fabric strip that secures the foot-and-calf massager to the frame into position, then secure it using two Phillips-head screws (Fig.11).

3. Place the fabric strip that secures the top rubber housing into position then secure it using Five Phillips-head screws (Fig.12).

4. Place the fabric strip that secure the bottom rubber housing into position then secure it using two Phillips-head screws (Fig.13).

5. Replace the two screws inside the open slot in the rubber housing.

6. On the underside of the chair, reconnect the connectors.

7. Using the zip-tie, secure the calf massager harness to the frame (Fig.14).

8. Place the connectors into position inside the connector junction box (Fig.15), replace the junction box cover, then replace the four screws

to secure it (Fig.16).

9. Use a new zip tie to secure the connector box to the chair frame (Fig.17).

10. Using two people, gently return the chair to an upright position.

11. Plug in the chair, power it on, then verify that the new foot and calf massager is working properly.

(Fig.11)

Foot-and-calf

massager

(Fig.12)

Fabric strip

(Fig.13)

(Fig.15) (Fig.16)

Zip ties

(Fig.17)

Connector box

Connectors

Please send any questions or comments regarding these instructions to: [email protected]

Zip-tie

(Fig.14)

Other manuals for HT-9200

This manual suits for next models

Table of contents

Other Human Touch Massager manuals

Human Touch

Human Touch WholeBody 2.0 User manual

Human Touch

Human Touch HT-270 User manual

Human Touch

Human Touch iJoy-2310 User manual

Human Touch

Human Touch HT-Navitas Sleep User manual

Human Touch

Human Touch NOVO User manual

Human Touch

Human Touch ht 7450 User manual

Human Touch

Human Touch ht 5320 User manual

Human Touch

Human Touch IJOY HT-2720 User manual

Human Touch

Human Touch ht 125 Operating and safety instructions

Human Touch

Human Touch feel better HT-5020 User manual

Human Touch

Human Touch iJoy250 User manual

Human Touch

Human Touch HT-1650 User manual

Human Touch

Human Touch CITYclub ht3010 User manual

Human Touch

Human Touch HT-1650 User manual

Human Touch

Human Touch CIRQLATION HT-1340 User manual

Human Touch

Human Touch HT-3000 User manual

Human Touch

Human Touch ThermoStretch HT-7120 User manual

Human Touch

Human Touch HT-120 Operating instructions

Human Touch

Human Touch Novo XT2 User manual

Human Touch

Human Touch REFLEX SWING Pro User manual

Human Touch

Human Touch feel better HT-245PS User manual

Human Touch

Human Touch HT 2720 User manual

Human Touch

Human Touch ThermoStretch HT-7120 User manual

Human Touch

Human Touch WholeBody 2.0 User manual

Popular Massager manuals by other brands

ELEEELS

ELEEELS P2 instruction manual

Cenocco

Cenocco CC-9111 user manual

Panasonic

Panasonic EP790-C1 Service manual

Adler

Adler AD 2167 user manual

Taurus

Taurus Wellness TW-MC-M Assembly and operating instructions

Infinity

Infinity Syner-D Circadian Assembly guide

Hydas

Hydas LH-095 instruction manual

AEG

AEG FM 5567 instruction manual

OBH Nordica

OBH Nordica Shiatus Tunes manual

Hutech

Hutech Q9 user manual

Medisana

Medisana MM 825 user manual

SOLAC

SOLAC Therma Hydro Instructions for use

Invacare

Invacare Texas user manual

Casada

Casada Bismarck II manual

Fujiiryoki

Fujiiryoki Cyber-Relax EC-1700 user manual

Medisana

Medisana HM 886 instruction manual

HoMedics

HoMedics BA-C200 instruction manual

Repose

Repose Lynton user manual