HP LaserJet 9000 User manual

Internal Peripherals Installation Guide

D Class and R Class

HP 9000 Enterprise Servers

Part No. A3262-90005

Edition 5

October 1998

E1098

Printed in: USA

Legal Notices

The information in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

manual, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard

shall not be held liable for errors contained herein or direct, indirect,

special, incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

Restricted Rights Legend. Use, duplication or disclosure by the U.S.

Government is subject to restrictions as set forth in subparagraph (c) (1)

(ii) of the Rights in Technical Data and Computer Software clause at

DFARS 252.227-7013 for DOD agencies, and subparagraphs (c) (1) and

FAR 52.227-19 for other agencies.

HEWLETT-PACKARD COMPANY

3000 Hanover Street

Palo Alto, California 94304

U.S.A.

rights reserved.

Reproduction, adaptation, or translation of this document without prior

written permission is prohibited, except as allowed under the copyright

laws.

Trademark Notices UNIX is a registered trademark in the United

States and other countries, licensed exclusively through X/Open

Company Limited.

Contents

iii

1. D Class Internal Peripherals Installation

Internal Peripherals Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Installation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Peripherals Installation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21

Peripherals Installation Verification Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

2. R Class Internal Peripherals Installation

Internal Peripherals Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Peripherals Installation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Peripherals Installation Verification Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Contents

Printing History

The manual printing date and part number indicate its current edition.

The printing date will change when a new edition is printed. Minor

changes may be made at reprint without changing the printing date. the

manual part number will change when extensive changes are made.

Manual updates may be issued between editions to correct errors or

document product changes. To ensure that you receive the updated or

new editions, you should subscribe to the appropriate product support

service. See your HP sales representative for details.

First Edition: October, 1995

Second Edition: May, 1996 (European, Localized)

Third Edition: May, 1996

Fourth Edition: August, 1998

Fifth Edition: October, 1998

NOTE Reader Comments. We welcome your comments about our

documentation. If you have editorial suggestions or recommended

improvements for this document, please write to us. You can reach us

through e-mail at: hardwaredocs@cup.hp.com or by sending your letter

to: Documentation Manager M/S 5657, Hewlett-Packard Company, 8000

Foothills Blvd., Roseville, CA 95747-6588 USA. Please include the

following information in your message:

• Title of the manual you are referencing.

• Manual part number (from the title page).

• Edition number or publication date (from the title page).

•Yourname.

• Your company’s name.

SERIOUS ERRORS, such as technical inaccuracies that may render a

program or a hardware device inoperative, should be reported to your HP

Response Center or directly to a Support Engineer.

Who Should Use this Guide

The procedures in this guide are intended to be performed by a person

who is qualified in the installation and servicing of computer equipment,

and is trained to recognize the hazards involved. Internal peripherals are

installed in an area of the product where energy levels considered

hazardous may be produced.

1-1

1 D Class Internal Peripherals

Installation

Internal Peripherals Installation

Overview

CAUTION If you are adding the Fast/Wide SCSI (Hot-Swap) option to a Model D2xx

server (step K in the list below), you must perform a full system backup

before starting the installation procedures.

NOTE Fast/Wide SCSI (Hot-Swap) disks are standard on Model D3xx servers,

and are available as an option on Model D2xx servers. The hot-swap disk

capability allows you to add Fast/Wide SCSI disks while power is on.

To install internal peripherals (other than Fast/Wide SCSI disks), you

must turn off system power, and open the server cabinet to gain access to

the cabinet interior. An overview of the procedures is given below:

A. Install Fast/Wide SCSI (hot-swap) disks.

B. Turn off power to the system.

C. Remove the front bezel.

D. Remove the side panel.

E. Remove the EMI cover.

F. Configure your peripheral, if necessary.

G. Select the peripheral slot in the cabinet.

H. Install the IDE floppy drive.

I. Install removable media drives (CD-ROM, DDS or quarter-inch tape

drives).

J. Install Single-Ended SCSI disks (Model D2xx only).

K. Install the Fast/Wide SCSI (hot-swap) disk option (Model D2xx only).

L. Replace the EMI cover.

M. Replace the side panel.

N. Replace the front bezel.

1-2 Chapter1

D Class Internal Peripherals Installation

Internal Peripherals Installation Overview

Aftercompletingthe installationprocedures, proceed to the Peripherals

Installation Verification section (located after the installation

procedures) for instructions on how to verify that internal peripherals

have been correctly installed.

Required Tools • Small flat-bladed screwdriver

• Torx driver, #15

• Torx driver, #10

• Phillips screwdriver

Safety Considerations

WARNING Turn off the system power and disconnect the power cable before

opening the system cabinet. Otherwise, personal injury may

occur.

Electrostatic

Discharge Precautions Electrostatic discharge can damage the integrated circuits on printed-

circuit boards. To prevent such damage from occurring, be sure to

observe the following precautions when handling and installing boards:

• Use a grounding mat and an anti-static wrist strap, such as those

included in the ESD Field Service Kit (HP P/N A3024-80004).

• Wear the anti-static wrist strap to ensure that any accumulated

electrostatic charge is discharged from you body to ground.

• Keep uninstalled printed-circuit boards in their protective anti-static

bags until you are ready to install them.

• Handle printed-circuit boards by their edges after you have removed

them from their protective anti-static bags.

Chapter 1 1-3

D Class Internal Peripherals Installation

Installation Procedures

A. Install Fast/Wide

SCSI Disks Fast/Wide SCSI disks (or Hot-Swap disks) can be installed while system

power is ON or OFF.

CAUTION You must follow proper hot-swap procedures before adding or replacing a

Fast/Wide SCSI disk. Refer to the Hot-Swap Procedure Guide for hot-

swap procedures and information before performing the following

installation procedure.

NOTE The hot-swap capability (up to five disks) is standard on Model D3xx

servers, and is available as a two-disk option on Model D2xx servers. To

add the optional hot-swap capability to your D2xx server, refer to the

procedure described in step K of this manual, then return to step A to

add the hot-swap disks.

1. Unlock the peripheral door using the key that was shipped with your

server. Open the peripheral door.

2. Pull out the latch of the disk so that it is in the open position.

3. Insert the disk into the peripheral slot.

1-4 Chapter1

D Class Internal Peripherals Installation

Installation Procedures

4. Push the disk all the way into the slot. The disk locking latch should

click shut when the disk is completely inserted. If it does not click,

gently push in the latch until you hear or feel the latch click into

place.

5. After installing all disks, close the peripheral door.

6. If no more peripherals are to be added, lock the peripheral door with

the key.

Other manuals for LaserJet 9000

Table of contents

Other HP Server manuals

HP ProLiant MicroServer User instructions

HP PROLIANT BL45P User manual

HP 376227-B21 - ProLiant InfiniBand 4x Fabric Copper... User manual

HP ProLiant 585G5 Quick guide

HP Sa3110 - VPN Server Appliance How to use

HP ProLiant TM200 Manual

HP Integrity BL890c - i2 Server Quick start guide

HP DL385 - ProLiant - G5 User instructions

HP ProLiant DL320e User manual

HP ProLiant XL730f Gen9 Server Operating instructions

HP T5125 - Compaq Thin Client Specification sheet

HP ProLiant ML310 Generation 5p User manual

HP ProLiant DL320 Generation 3 Manual

HP T5125 - Compaq Thin Client User manual

HP HPE XL270d Installation instructions

HP ProLiant BL685c G6 Manual

HP LC2000r - NetServer - 128 MB RAM User manual

HP T5720 - Compaq Thin Client Quick start guide

HP ProLiant DL560 User instructions

HP QUICKSPECS BL20P User manual

HP ProLiant DL360p User manual

HP Virtual Connect FlexFabric-20/40 F8 Module User instructions

HP Integrity BL870c User instructions

HP BladeSystem bc2000 - Blade PC User manual

Popular Server manuals by other brands

Dell

Dell PowerEdge R410 Getting started

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

Dell

Dell PowerEdge XE9640 Installation and service manual

Dell

Dell PS4100 Hardware

EtroVISION

EtroVISION EV3151 user manual

NEC

NEC Express5800/T110j System configuration guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

Dell

Dell PowerEdge 3YPMN Getting started guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual

Lenovo

Lenovo ThinkSystem SR635 V3 user guide

Dell

Dell PowerEdge HS5610 Installation and service manual