HP LaserJet 9000 User manual
I/O Card Installation Guide
D Class and R Class
HP 9000 Enterprise Servers
Part No. A3262-90007
Mfg. Part No. A3262-96127
Edition 4- November 1998
E1198
Printed in: USA
ii
Legal Notices
The information in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this manual,
including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. Hewlett-Packard shall not be held liable for errors
contained herein or direct, indirect, special, incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Restricted Rights Legend. Use, duplication or disclosure by the U.S. Government
is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in
Technical Data and Computer Software clause at DFARS 252.227-7013 for DOD
agencies, and subparagraphs (c) (1) and (c) (2) of the Commercial Computer
Software Restricted Rights clause at FAR 52.227-19 for other agencies.
HEWLETT-PACKARD COMPANY 3000 Hanover Street Palo Alto, California
94304 U.S.A.
Copyright Notices. ©copyright 1983-97 Hewlett-Packard Company, all rights
reserved.
Reproduction, adaptation, or translation of this document without prior written
permission is prohibited, except as allowed under the copyright laws.
Trademark Notices. UNIX is a registered trademark in the United States and other
countries, licensed exclusively through X/Open Company Limited.
Contents
iii
Who Should Use this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
1. I/O Card Installation Guide
I/O Card Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
I/O Card Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
I/O Card Installation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
I/O Card Installation Verification Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
2. R Class I/O Card Installation
I/O Card Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
I/O Card Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
I/O Card Installation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
I/O Card Installation Verification Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
iv
Contents
v
Printing History
The manual printing date and part number indicate its current edition. The printing
date will change when a new edition is printed. Minor changes may be made at
reprint without changing the printing date. the manual part number will change
when extensive changes are made.
Manual updates may be issued between editions to correct errors or document
product changes. To ensure that you receive the updated or new editions, you should
subscribe to the appropriate product support service. See your HP sales
representative for details.
First Edition: November, 1995
Second Edition: November, 1996
Third Edition: August, 1997
Fourth Edition: November, 1998
NOTE Reader Comments. We welcome your comments about our documentation. If you
have editorial suggestions or recommended improvements for this document, please
sending your letter to: Documentation Manager, M/S 5657, Hewlett-Packard
Company, 8000 Foothills Blvd., Roseville, CA 95747-6588 USA. Please include the
following information in your message:
• Title of the manual you are referencing.
• Manual part number (from the title page).
• Edition number or publication date (from the title page).
• Your name.
• Your company’s name.
SERIOUS ERRORS, such as technical inaccuracies that may render a program or a
hardware device inoperative, should be reported to your HP Response Center or
directly to a Support Engineer.
vi
Who Should Use this Guide
The procedures in this guide are intended to be performed by a person who is
qualified in the installation and servicing of computer equipment, and is trained to
recognize the hazards involved. Internal peripherals are installed in an area of the
product where energy levels considered hazardous may be produced.
1
1 I/O Card Installation Guide
I/O Card Installation Overview
To install I/O cards, you must turn off system power, and disassemble the system to
gain access to the cabinet interior. An overview of the procedure is given below:
A. Turn off power to the system.
B. Remove the front bezel.
C. Remove the side panel.
D. Remove the EMI cover.
E. Remove the I/O card retainer bracket.
F. Remove the I/O slot cover plate from bulkhead.
G. Set I/O card configuration.
H. Install HSC cards.
I. Install EISA cards.
J. Replace the I/O card retainer bracket.
K. Replace the EMI cover.
L. Replace the side panel.
M. Replace the front bezel.
N. Refer to I/O card-specific documents.
After completing all desired procedures, you should proceed to the I/O Card
Installation Verification section later in this chapter for procedures to verify that I/
O cards have been correctly installed.
Required Tools • Small flat-bladed screwdriver
• Torx driver, #15
• Torx driver, #10
• Phillips screwdriver.
2
I/O Card Installation Guide
I/O Card Installation Overview
Safety
Considerations
WARNING The installation procedures in this guide require opening the system cabinet,
which may expose you to high-energy (high-amperage) circuits, possible
ejection of molten metal, and exposed sharp edges in equipment chassis. Be
sure to remove all rings, watches, and other jewelry from fingers, wrists, and
arms before opening the system cabinet.
Electrostatic
Discharge
Precautions
Electrostatic discharge can damage the integrated circuits on printed-circuit boards.
To prevent such damage from occurring, be sure to observe the following
precautions when handling and installing boards:
1. Use a grounding mat and an anti-static wrist strap, such as those included in the
ESD Field Service Kit (HP P/N A3024-80004).
2. Wear the anti-static wrist strap to ensure that any accumulated electrostatic
charge is discharged from you body to ground.
3. Keep uninstalled printed-circuit boards in their protective anti-static bags until
you are ready to install them.
4. Handle printed-circuit boards by their edges after you have removed them from
their protective anti-static bags.
3
I/O Card Installation Guide
I/O Card Installation Procedure
I/O Card Installation Procedure
A. Turn Off Power
to the System 1. Set the computer front panel Power switch to the OFF position.
2. After the system has properly completed shutdown and internal DC power has
turned off, disconnect the power cord from the server cabinet.
4
I/O Card Installation Guide
I/O Card Installation Procedure
B. Remove the
Front Bezel 1. Unlock the front peripheral door using the key that was shipped with your
server.
2. Grab the bottom sides of the front bezel, and pull thebottom of the bezel slightly
out from the cabinet.
3. Carefully push the bezel up so that the top of the bezel comes loose from the top
of the cabinet, then pull the bezel away from the cabinet.
Other manuals for LaserJet 9000
9
Table of contents
Other HP Server manuals
HP
HP D7171A - NetServer - LPr User manual
HP
HP t510 Operating and maintenance manual
HP
HP D7171A - NetServer - LPr User manual
HP
HP Integrity NonStop X NS7 Technical manual
HP
HP Integrity rx1620 Operating manual
HP
HP PROLIANT BL45P User manual
HP
HP Integrity rx4640 User manual
HP
HP 9000 EPS20 User manual
HP
HP Compaq AlphaServer DS10 Installation guide
HP
HP D7171A - NetServer - LPr Parts list manual
HP
HP t5630 - Thin Client User manual
HP
HP 345646-001 - StorageWorks NAS 2000s External Storage... User manual
HP
HP ProLiant xw25p User manual
HP
HP 9000 rp4440 Installation and operation manual
HP
HP ProLiant BL490c - G6 Server User manual
HP
HP DL385 - ProLiant - G5 User instructions
HP
HP ProLiant DL160 Gen8 User manual
HP
HP ProLiant ML310e User manual
HP
HP 70001A User manual
HP
HP HPE ProLiant DL365 Gen10 Plus Server User manual
