HP D7171A - NetServer - LPr Installation and operation manual
HP Part Number 5967-5277
Printed in October 1998
HP NetServer LXr 8000
Memory Upgrade Guide
ii
Notice
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard
shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or
use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated to another language without the
prior written consent of Hewlett-Packard Company. Information in this
document is subject to change without notice.
PentiumTM is a U.S. trademark of Intel Corporation.
Hewlett-Packard Company
Network Server Division / MS 45S-LE
Technical Communications
10955 Tantau Avenue
Cupertino, CA 95104 USA
© Copyright 1998, Hewlett-Packard Company
iii
Audience Assumptions
This guide is for the person who installs, administers, and troubleshoots
LAN servers. Hewlett-Packard Company assumes that you are qualified
to service computer equipment and trained in recognizing hazards in
products with hazardous energy levels.
v
Contents
Preface......................................................................................................1
Introduction............................................................................................1
Purpose of this Guide............................................................................2
Related Documentation.........................................................................2
Tools You Need.....................................................................................2
1 Preparing for Installation....................................................................3
Verify Contents......................................................................................3
Prepare for Installation..........................................................................5
2 Installing Memory and Memory Boards .............................................7
Memory Configuration Guidelines.........................................................7
Removing the Memory Board..............................................................18
Installing DIMMs on the Memory Board..............................................21
Removing DIMMs From the Memory Board........................................23
Replacing the Memory Board..............................................................25
3 Warranty and Support........................................................................29
Hardware Warranty.............................................................................29
HP Repair and Telephone Support.....................................................30
1
Preface
Introduction
The HP NetServer LXr 8000 is an Intel-CPU based network server that
can use up to 8 GB of memory. This memory is situated on two boards
that communicate with the rest of the NetServer via the midplane
connector.
Each memory board can hold up to 4 GB of memory, arranged in four
banks of four buffered DIMMs. These DIMMs can be 64 MB or 256
MB, 50 ns EDO memory.
The standard configuration of memory is 256 MB on the primary (right)
board, as four 64 MB DIMMs in slots J1 through J4. Add memory four
DIMMs at a time. If you use both boards, each must have the same type
and number of DIMMs in the same slots.
2
Purpose of this Guide
This guide tells how to:
• Remove and reinstall the HP NetServer LXr 8000 memory board
for a memory upgrade
• Install DIMMs in the specified interleave configuration on the
memory board
• Remove DIMMs and downsize the memory configuration
Related Documentation
The following documents describe the HP NetServer LXr 8000:
•The HP NetServer LXr 8000 Installation Guide
•HP NetServer LXr 8000 Technical Reference Card
•HP NetServer Online Documentation CD-ROM
Tools You Need
To install this accessory kit, you need the following tools:
•An anti-static service kit (3M8501/8502/8503 or equivalent).
This kit includes a static-dissipating work surface, a chassis clip
lead, and a wrist strap.
3
1 Preparing for Installation
Verify Contents
CAUTION Do not remove the DIMM from its bag until you are
ready to install it. Make sure the bag remains sealed.
The DIMM is sensitive to humidity, so desiccant has
been packed in the bag containing the DIMM. When
the DIMM has been installed and the HP NetServer is
running, it is no longer sensitive to humidity.
Unpack the shipping box and verify that you received the contents listed
below for the Memory Upgrade Kit.
The upgrade kit includes:
•Four DIMM memory modules, either 64 MB or 256 MB buffered
EDO DIMMs (50 ns)
4
Figure 1-1. EDO DIMM
NOTE Be sure to keep the bag around the DIMM sealed until
you are ready to install it.
•HP NetServer Memory Upgrade Guide (this document)
Other manuals for D7171A - NetServer - LPr
117
This manual suits for next models
6
Table of contents
Other HP Server manuals
HP
HP ProLiant DL380p User manual
HP
HP ProLiant SL230s User manual
HP
HP ProLiant xw25p User manual
HP
HP D5970A - NetServer - LCII User manual
HP
HP 4700 Installation and user guide
HP
HP D7171A - NetServer - LPr User manual
HP
HP ProLiant ML110 User instructions
HP
HP ProLiant ML110 G6 Manual
HP
HP ProLiant WS460c G6 Workstation Blade User manual
HP
HP A4500A - VMEbus Single Board Computer 744... Owner's manual
HP
HP ProLiant DL320e Gen8 v2 User manual
HP
HP 16-way User manual
HP
HP HPE XL270d Installation instructions
HP
HP PROLIANT BL45P Manual
HP
HP T5720 - Compaq Thin Client Quick start guide
HP
HP AlphaServer TS15 User manual
HP
HP ProLiant DL160 Generation 6 Manual
HP
HP 70001A User manual
HP
HP D5970A - NetServer - LCII User manual
HP
HP ProLiant BL620c G7 User manual
