HP 9x9KS Series Quick start guide

CPU Upgrade Manual

Model 9x9KS and Series Kxx0

HP 3000 and HP 9000 Enterprise Servers

Part No. A2375-90012

Printed in U.S.A. March 1999

Edition 8, 0399

Legal Notices

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited

to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or direct, indirect, special, incidental or consequential damages

in connection with the furnishing, performance, or use of this material.

Restricted Rights Legend. Use, duplication or disclosure by the U.S. Government is subject to

restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the

Commercial Computer Software Restricted Rights clause at FAR 52.227-19 for other agencies.

HEWLETT-PACKARD COMPANY

3000 Hanover Street

Palo Alto, California 94304 U.S.A.

Reproduction, adaptation, or translation of this document without prior written permission is prohibited,

except as allowed under the copyright laws.

Trademark Notices. UNIX is a registered trademark in the United States and other countries, licensed

exclusively through X/Open Company Limited.

iii

Printing History

New editions of this manual incorporate all material updated since the previous edition. The manual

printing date and part number indicate its current edition. The printing date changes when a new edition

is printed. (Minor corrections and updates which are incorporated at reprint do not cause the date to

change.) The manual part number changes when extensive technical changes are incorporated.

February 1995...............................................................................................................................Edition 1

September 1995 ...........................................................................................................................Edition 2

January 1996.................................................................................................................................Edition 3

June 1996......................................................................................................................................Edition 4

July 1997 ......................................................................................................................................Edition 5

January 1998 ................................................................................................................................Edition 6

August 1998 ................................................................................................................................Edition7

March 1999...................................................................................................................................Edition 8

Change Narrative

• Edition 8 technical changes include minor changes and updates as required.

• Edition 7 technical changes include:

a. The addition of 989KS to the supported CPU table on page 1.

b. The addition of 929KS/020 to the NOTE on page 1 of Chapter 1.

c. Minor changes and updates as needed.

• Edition 6 technical changes include:

a. The addition of HP9000/K380/K580 information throughout the manual.

b. Minor changes and updates as needed.

Reader Comments

Reader Comments. We welcome your comments about our documentation. If you have editorial

suggestions or recommend improvements for this document, please write to us. You can reach us through

e-mail at: hardwared[email protected].com or by sending your letter to: Documentation Manager, M/S 5657,

Hewlett-Packard Company, 8000 Foothills Blvd., Roseville, CA 95747-5657 USA. Please include the

following information in your message:

• Title of the manual you are referencing.

• Manual part number (from the title page).

• Edition number or publication date (from the title page).

• Your name.

• Your company’s name.

SERIOUS ERRORS, such as technical inaccuracies that may render a program or a hardware device

inoperative, should be reported to your HP Response Center or directly to a Support Engineer.

Preface

This edition of the CPU Upgrade Manual contains technical information about HP 9000 and HP3000

Servers. The HP 9000 family of Servers includes the following models:

The HP 3000 family of Servers does not include CPU Module Product Numbers.

HP9000/Kxx0

Servers HP9000 Workstations CPU Module

Product No.

K100 N/A

K200 A2993A

K210 A2995A

K220 A3452A

K250 A3498A

K260 HP VISUALIZE K260-EG A3261A

K360 A5140A

K370 A3669A

K380 A4872A

K400 A2993A

K410 A2995A

K420 A3452A

K450 A3498A

K460 HP VISUALIZE K460-EG/XP A3261A

K570 A3669A

K580 A4872A

CPU Upgrade

Electrostatic Discharge

1CPU Upgrade

The Central Processing Unit (CPU) upgrade for the HP 3000 and HP 9000 system is accomplished by

adding CPU cards to the existing CPU card slots within the computer cabinet. The number of CPUs

supported on each system model is as follows:.

NOTE CPUs for HP 9000/K100 models are an integral part of the system board. There is

no CPU upgrade for these models.

929KS/020, 939KS, and 939KS/020 models support a single processor only.

Electrostatic Discharge

CPU cards and computer systems contain assemblies and components that are sensitive to electrostatic

discharge (ESD). Carefully observe the precautions listed in this section and use the ESD wrist strap,

ESD sheet, and ESD foam pad provided in the ESD kit (part number A3024-80004).

The following precautions can significantly reduce the risk of system failure or component damage due

to ESD.

• Always wear an anti-static wrist strap when working around a system or handling the CPU card.

• Treat all assemblies, components, cards, and connections as sensitive.

• When unpacking cards or components to the system, keep the item in it's conductive bag until it is

ready to be installed.

• Keep body movement to a minimum, this generates static electricity that causes ESD.

• Avoid working in carpeted areas.

• Try to select a work area where potential static sources are minimized.

Anti-Static Wrist Strap

The anti-static wrist strap is a bracelet-like strap that goes around either wrist. The other end of the strap

connects to a convenient metal surface on the computer cabinet.

Models

HP3000/

9x9KS

(except

989KS)

HP3000/

989KS HP9000/

K2x0 HP9000/

K360/K4x0 HP9000/

K370/380 HP9000/

K570/580

CPUs Supported 1 to 4 1 to 6 1 to 4 1 to 4 1 to 6 1 to 6

CPU Upgrade

CPU Configuration Rules

Anti-Static Mat

The anti-static mat can be either the conductive bag, the ESD sheet, or the ESD foam pad. The anti-static

mat does not have to be connected to the cabinet. It should be placed close to the computer while

performing the upgrade tasks.

CPU Configuration Rules

The rules for adding a CPU to a system are as follows:

1. The computer must have a CPU installed in slot 0 (zero).

2. All additional CPUs are added in sequential order (1, 2,... and so on).

Once the CPU card is added to the computer, it is automatically configured into the system during the

computer power on selftest process.

CPU Location

The CPU slots for both the HP 3000/9x9KS and HP 9000/K2xx and K4xx SPUs are the same. Figure 1-1

and Figure 1-2 shows the CPU locations for these systems. Figure 1-1, front view, shows the system with

the front bezel and bulkheads (or cover plates) removed. Figure 1-2, rear view, shows the system with the

back cover removed.

Figure 1-1 CPU Location, Front View (All Models)

Item 2 shows the location of CPU slots 0 and slot 1. Slot 0 is located next to the power monitor and Slot

1 is located next to the peripheral cage.

CPU Upgrade

CPU Location

Figure 1-2 CPU Location, Rear View 9x9KS, K2xx, K360, and K4xx (Except 979 and 989KS)

Item 3 shows the location of CPU slot 2 and slot 3 (see the note following). Slot 2 is located next to the

power supply and slot 3 is located to the left of CPU slot 2.

NOTE On HP3000/979KS/989KS and HP9000 models, the power supply and processor

covers conceal slots 2 and 3. Access to these slots requires removal of the power

supply.

Figure 1-3 CPU Location, Rear View K370/K570, K380/K580, and 979KS/989KS

Figure 1-3 shows the location of CPU slots 2 through 5. Slot 4 is located between slots 3 and 5. Slot 5 is

located next to the Kx70/Kx80 HP-HSC expansion slot.

CPU Upgrade

Tools required

To accomplish adding a CPU to the computer the following tools are required:

• A Torx #10 driver. (This is the preferred tool)

• A flat blade screw driver. (this can be used if a Torx driver is not available)

• A3204-80004 ESD Kit (included with the CPU Upgrade Kit)

Adding a CPU Card

Be sure to observe all ESD precautions. The suggested time to perform the upgrade is at a non-peak

usage time for the computer. You must also know how many CPUs are already in the computer, this will

determine if you add to the available front slot (1) or the rear slots (2 and 3). Once you have identified

which slot or slots to add to, reference the appropriate procedures for adding a CPU card.

Before starting the actual installation of a CPU card there are certain preparation procedures to perform:

1. Log Off all users and stop all active applications that may be running.

2. Perform a system backup of the entire Operating System and data base. If this is not feasible, perform

a backup of the data base. (This should be done at a scheduled interval as common practice for

protecting any new data or changes to the existing data base.)

3. Perform a system shutdown. Enter “/etc/shutdown -h” at the prompt.

4. Turn the computer key switch to the STANDBY position.

5. At the rear of the computer, unplug the power cord.

Adding CPU #1

1. Remove the computer key from the switch.

2. Reach down, under each front lower corner of the front Bezel (Figure 1-4), press the latch tabs (item

1) and pull the bottom of the front bezel away from the computer.

CPU Upgrade

Adding a CPU Card

Figure 1-4 Front Bezel Removal

3. The front bezel should unhinge from the top of computer with the bottom of the bezel angled away

from the computer.

4. With the Torx driver (or flat blade screw driver) remove the CPU/Memory cover plate (Item1, Figure

1-5) by loosening the four (two top and two bottom) captive screws.

Figure 1-5 CPU/Memory Cover Plate

5. Identify CPU slot 1 and carefully reach into the computer cabinet and remove the CPU connector

dust cover, on the system board, by grasping the extended tab and pulling it out.

6. Remove the protective dust cover from the CPU card and align the CPU card into slot 1. Be sure

the air guide and card components are on the right-hand side of the card during installation.

7. Insert the CPU card until it contacts the system board connector, then press firmly to seat the card.

8. Replace the CPU/Memory cover plate and tighten the four captive mounting screws.

9. Replace the bezel by angling the top of the bezel toward the computer while slipping the top edge

under and up into the top overhang of the computer.

10.Then push the bottom of the bezel onto the computer cabinet until the mounting tabs snap into place.

At this point, refer to the Installation Verification section to determine how to ensure that the computer

has configured the new CPU(s).

This manual suits for next models

Table of contents

Other HP Server manuals

HP ProLiant ML310G5 Installation instructions

HP ProLiant 400 Use and maintenance manual

HP ProLiant ML310e Gen Manual

HP D7171A - NetServer - LPr User manual

HP t5325 - Thin Client User manual

HP st5742 - Streaming Client User manual

HP A180 Technical manual

HP NetServer E60 User manual

HP ProLiant ML350p Gen8 User manual

HP ML350 - ProLiant - G2 User manual

HP Integrity rx2600 User manual

HP ProLiant ML115 G5 User instructions

HP T5700 - compaq thin client User manual

HP Pavilion t100 - Desktop PC Operating and maintenance manual

HP ProLiant DL160 Gen9 User manual

HP DL360 - ProLiant - Photon User manual

HP ProLiant DL180 G6 Assembly instructions

HP T5720 - Compaq Thin Client Manual

HP ML570 - ProLiant - G2 Operating and safety instructions

HP D5970A - NetServer - LCII User manual

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... User manual

HP hpe proliant dl20 gen9 User manual

HP cc2300 User manual

HP AlphaServer DS15 Specification sheet

Popular Server manuals by other brands

Dell

Dell PowerEdge R410 Getting started

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

Dell

Dell PowerEdge XE9640 Installation and service manual

Dell

Dell PS4100 Hardware

EtroVISION

EtroVISION EV3151 user manual

NEC

NEC Express5800/T110j System configuration guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

Dell

Dell PowerEdge 3YPMN Getting started guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual

Lenovo

Lenovo ThinkSystem SR635 V3 user guide

Dell

Dell PowerEdge HS5610 Installation and service manual